Designer-Style RF Slim-Button Keypads HRD-5KP, -5RL, -10KP, -10RL 120 V , 0.5 A, 50/60 Hz HRD-5KP HRD-5RL HRD-10KP HRD-10RL Installation Instructions Please Read Before Installing Overview The HRD-5KP, -5RL, -10KP, and -10RL keypads are for use with HomeWorks systems. The keypad buttons are programmed with a personal computer using the HomeWorks Utility. Up to 32 keypads, each with a unique address, can be assigned to each HomeWorks RF Processor. Important Notes Codes: Install in accordance with all local and national electrical codes. Environment: Ambient operating temperature:
0-40C, 32-104F, 0-90% humidity, non-condensing. Indoor use only. Wallplates: Lutron Claro and Satin ColorsTM wallplates are recommended for best color match and clean aes-
thetic appearance. Do not paint controls or wallplates. Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning solutions. Wallboxes: Lutron recommends using 3-1/2 in. (89 mm) deep wallboxes for easier installation. RF Device Placement: RF Keypads must be located within 30 feet (9 m) of an RF Signal Repeater or an RF Processor. RF Keypads will not function until they are addressed and programmed. See the HomeWorks Utility online help. 1 5. Attach Lutron Claro or Satin ColorsTM wallplate adapter and wallplate. a. Loosely install keypad mounting screws. b. Tighten wallplate adapter mounting screws snug. c. Tighten keypad mounting screws until wallplate adapter is flush to wall (do not over-
tighten). d. Snap wallplate onto wallplate adapter, and verify that buttons are not submerged. e. If buttons are submerged, loosen keypad mounting screws appropriately. 6. Restore power. Installation 1. Turn power OFF at fusebox or circuit breaker. Danger - Locate and remove fuse or lock circuit breaker in the OFF position before proceeding. Wiring with power ON may result in personal injury. 2. Prepare wires. When making wire connections, fol-
low the recommended strip lengths and combina-
tions for the supplied wire connectors. Note: Wire connectors provided are suitable for copper wire only. Small:
Strip insulation 3/8 in. (10 mm) for 14 AWG (2.5 mm2). Strip insulation 1/2 in. (13 mm) for 16 AWG (1.5 mm2). Use to join one 14 AWG supply wire with one 16 or 18 AWG (1.0 mm2) control wire. Small 3. Wiring: See Wiring Diagram (page 3). 4. Push all wires back into the wallbox and loosely fasten the control to the wallbox using the keypad mounting screws provided. Do not pinch the wires. Mounting Diagram Keypad Mounting Screws Adapter Mounting Screws Wallbox Included:
Keypad Wire Connectors (3) Wallplate and Adapter are purchased separately. Mounting Screws (2) 2 Wiring Diagram Hot/Live Black 120/127 VAC 50/60 Hz Neutral White Green Earth/Ground Troubleshooting Guide RF Keypads will not function until they are addressed and programmed. See the HomeWorks Utility online help. Symptom LEDs don't light up when buttons are pressed. Cause and Action Power not present at keypad Circuit breaker OFF. Turn ON breaker. Wiring error. Check wiring to be sure it agrees with installation . Button presses on keypad cause the keypad to quickly flash all its LEDs simultaneously. Keypad has not been addressed. See the HomeWorks Utility online help for setup details. Button presses on keypad cause the keypad to slowly flash all its LEDs simultaneously. Keypad has an address, but does not have a valid programming database. See the HomeWorks Utility online help for programming details. Keypad cannot be addressed. Keypad is out of RF communications range. Move RF Signal Repeater or RF Processor to within 30 feet of keypad. LEDs light when button is pressed, but the system response is not correct. Improper programming Check programming in HomeWorks Utility. 3 FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the seperation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the users authority to operate this equipment. Industry Canada Information The term IC: before the radio certification number only signifies that Industry Canada tech-
nical specifications were met. Technical and Sales Assistance If you need assistance, call the toll-free Lutron Technical Support Center. Please provide exact model number when calling.
(800) 523-9466 (U.S.A., Canada and the Caribbean) Other countries call:
Tel: (610) 282-3800 Fax:
(610) 282-3090 Visit our Web site at www.lutron.com Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 Made and printed in the U.S.A. 7/03 P/N 043-099 Rev. A LIMITED WARRANTY Lutron will, at its option, repair or replace any unit that is defective in materials or manufac-
ture within two years after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. After the two year period, a pro-rated warranty applies to this product until eight years after the purchase. For more infor-
mation regarding this warranty contact your Lutron representative. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PUR-
CHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES. LUTRONS LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limi-
tation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This product may be covered by one or more of the following U.S. patents: 4,835,343;
4,889,999; 5,170,068; 5,736,965; 5,838,226; 5,848,054; 5,905,442; 5,982,103; D344,068;
D378,814 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, Claro, and HomeWorks are registered trademarks and Satin Colors and the HomeWorks logo are trademarks of Lutron Electronics Co., Inc. 2003 Lutron Electronics Co., Inc.