all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.53 MiB | ||||
1 |
|
User Manual (additional) | Users Manual | 852.95 KiB | ||||
1 | Cover Letter(s) | |||||||
1 | Attestation Statements | |||||||
1 | Block Diagram | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 1.53 MiB |
Radio Powr Savr Installation Instructions Please Read Before Installing English 14 A 434 MHz (Occupancy / Vacancy) 14 A 434 MHz (Vacancy-Only) Wireless Battery-Powered Occupancy and Vacancy Sensors California Title 24 Compliant LRF2-OCRB-P 3 V LRF2-VCRB-P 3 V Compatible Products For a full list of compatible products visit www.lutron.com/occsensors Product Description Lutrons ceiling-mounted Occupancy and Vacancy Sensors are wireless, battery-powered, passive infrared (PIR) devices that automatically control lights via RF communication with a dimming or switching device. These Sensors detect the heat from people moving within an area to determine when the space is occupied. The Sensors then transmit the appropriate commands to the associated dimming or switching device to turn the lights on or off automatically, providing both convenience and exceptional energy savings. A 1 2
Easy-to-follow Instructions P/N 041-272B Important Notes 1. This Sensor is part of a system and cannot be used to control a load without a compatible dimming or switching device. Refer to the instruction sheets of the receiving device(s) for installation information. 2. Clean Sensor with a soft damp cloth only. DO NOT use any chemical cleaners. 3. The Sensor is intended for indoor use only. Operate between 32 F and 104 F
(0 C and 40 C). 4. DO NOT paint Sensor. 5. Use only high-quality lithium batteries, size CR123, 3 V
(ANSI-5018LC, IEC-
CR17345). DO NOT use rechargeable batteries. Using improperly rated batteries could damage the Sensor. NOTICE: DO NOT disassemble, crush, puncture, or incinerate batteries. DO NOT dispose of batteries in normal household waste. Please recycle, take to a proper battery disposal facility, or contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries. complex factors such as:
6. The range and performance of the RF system is highly dependent on a variety of Distance between system components Geometry of the building structure Construction of walls separating system components Electrical equipment located near system components WARNING: Entrapment hazard. To avoid the risk of entrapment, serious injury, or death, these controls must not be used to control equipment which is not visible from every control location or which could create hazardous situations such as entrapment if operated accidentally. Examples of such equipment which must not be operated by these controls include (but are not limited to) motorized gates, garage doors, industrial doors, microwave ovens, heating pads, etc. It is the installers responsibility to ensure that the equipment being controlled is visible from every control location and that only suitable equipment is connected to these controls. Failure to do so could result in serious injury or death. Key Features Low Maintenance. 10-year battery life. Convenient low-battery indicator. Multiple Devices. Up to 3 Sensors can work together to control lights for broader coverage in large spaces. Each Sensor may be added to a maximum of 10 receiving devices. Sensor Operation Occupancy Version The Sensor will automatically turn the lights on when the space is occupied and automatically turn the lights off after the space is vacated. Vacancy-Only Version The lights must be manually turned on* at the dimming or switching device. The Sensor will automatically turn the lights off after the space is vacated.
* There is a built-in 15-second vacancy grace period that begins when the lights are automatically turned off, during which the lights will automatically turn back on in response to motion. This grace period is provided as a safety and convenience feature in the event that the lights turn off while the room is still occupied, so that the user does not need to manually turn the lights back on. After 15 seconds, the grace period expires and the lights must be manually turned on. NOTE: For either Sensor version, the lights can also be manually turned off at any time by using the dimming or switching device directly. Technical Assistance For questions concerning the installation or operation of this product, call the Lutron Technical Support Center. Please provide exact model number when calling. U.S.A. and Canada (24 hrs / 7days) 1.800.523.9466 Mexico 8am 8pm ET
+1.888.235.2910 Other countries 8am 8pm ET
+1.610.282.3800 Fax +1.610.282.6311 www.lutron.com FCC Information NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modi cations not expressly approved by Lutron Electronics Co. could void the Increase the separation between the equipment and receiver. users authority to operate this equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Limited Warranty
(Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.) Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRONS LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CON NEC TION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PUR CHASE PRICE OF THE UNIT. This warranty gives you speci c legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply to you. Lutron, Maestro Wireless, and the Sunburst logo are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American National Standards Institute. IEC is a trademark of the International Electrotechnical Commission. 3M and Command are trademarks of 3M Company 2010 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. Printed in the U.S.A. 07/10 P/N 041-272 Rev. B Instructions Pre-Installation Before setting up the Sensor, the corresponding dimming or switching device(s) should be installed. Refer to that products installation sheet for instructions. Install a Sensor in as little as 15 minutes Twist and remove mounting bracket to insert battery. Battery Release Tab Set-Up In order for the Sensor to operate properly, it must rst be set up with a corresponding dimming or switching device. The procedure for setting up a Sensor with a Maestro Wireless (MRF2-only) Dimmer or Electronic Switch is detailed below. If setting up a Sensor with a different device, visit www.lutron.com/occsensors or consult the installation guide for that device for the correct set-up procedure. Setting up a Sensor with a Maestro Wireless Dimmer or Electronic Switch Place the Dimmer or Electronic Switch in set-up mode by pressing and holding the tap button for approximately 6 seconds until all LEDs on the device begin ashing. Release the tap button. Dimmer Switch Add the Sensor to the Dimmer or Electronic Switch by pressing and holding the Lights Off button on the front of the Sensor for approximately 6 seconds until the lens ashes brie y. The lights in the room will also ash 3 times, indicating the Sensor has been successfully added. The Dimmer or Electronic Switch will exit set-up mode automatically. The Lights On and Lights Off buttons should now switch the lights in the room on and off, respectively, when pressed. Repeat the above procedure to set up the Sensor with any additional devices. Setting the Occupancy Light Level (Occupancy version, dimming devices only) Set the Dimmer to the desired light level for entering the room. B 1 1.1 1.2 1.3 2 2.1 2.2 Save the occupancy light level by pressing and holding the Lights On button on the front of a Sensor that has been set up. After approximately 6 seconds, the lens will ash rapidly several times, indicating the light level has been saved. All Sensors set up with the Dimmer will now use the saved occupancy light level. C Sensor Placement and Coverage Before mounting the Sensor, please note the following:
The Sensor is designed for ceiling use only. DO NOT install on ceilings higher than 12 ft (3.7 m) or non-ceiling surfaces. Doing so may signi cantly inhibit the Sensors performance.
The Sensor should be installed in a location where it has a good view of all parts of the room. The Sensor requires line of sight to operate properly. If you cannot see the Sensor, it cannot see you. The Sensor cannot see through glass objects such as patio or shower doors.
DO NOT mount the Sensor within 4 ft (1.2 m) of HVAC vents, within 6 in (15 cm) of other RF devices, or within 4 ft (1.2 m) of light bulbs installed below the ceiling line.
The Sensor may be installed up to 60 ft (18.3 m) away from the associated dimming or switching device(s) if they are in direct line of sight. If there are walls or other barriers between the Sensor and receiving device(s), the Sensor should be located within 30 ft (9.1 m).
Whenever possible, avoid placing the Sensor in a location where it has a broad view outside the intended space. If this is unavoidable, the lens can be masked to block the view of undesired areas (refer to section I. Lens Masking).
The Sensors detection range is dependent on the ceiling height, as shown in the table below. Coverage Chart (for sensor mounted in center of room) Ceiling Height 8 ft (2.4 m) Max. Room Dimensions for Complete Coverage 18 x 18 ft (5.5 x 5.5 m) Radius of Coverage at Floor 13 ft (4.0 m) D 1 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 10 ft (3.0 m) 22 x 22 ft (6.7 x 6.7 m) 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 14.5 ft (4.4 m) 16 ft (4.9 m) 19 ft (5.8 m) Temporary Mounting Methods If you are uncertain about correctly positioning the Sensor, the following temporary mounting and testing procedures are recommended to verify proper performance before permanently installing the Sensor. Temporary Mounting: Drop Ceiling Use this procedure if the Sensor will be mounted on a ceiling tile. The ceiling tile mounting wire is provided for both temporary and permanent mounting of the Sensor to drop ceilings composed of multiple tiles. It is designed to allow temporary mounting, testing, and repositioning (if necessary) of the Sensor without damaging a ceiling tile. Once the Sensors nal position has been chosen, the mounting wire can be twisted to lock the Sensor in place permanently. 1.1 Insert the ceiling tile mounting wire through the two smaller holes in the mounting bracket and replace the mounting bracket. 1.2 Temporarily mount Sensor to a ceiling tile by inserting the wire legs through the tile, making sure the Sensor is ush to the tile. Note: Do not twist wire legs together until G. Permanent Mounting Methods. 1.3 1.4 1.5 2 Perform the Sensor coverage and wireless communication tests as described in sections E. Testing Sensor Coverage and F. Testing Wireless Communication. If the Sensor does not perform satisfactorily from this location, it may be moved to another location by pulling the Sensor straight down and repeating steps 1.2 and 1.3. If the Sensors performance is satisfactory, it should be permanently attached to the ceiling tile, as described in section G. Permanent Mounting Methods. Temporary Mounting: Solid Ceiling Use this procedure if the Sensor will be mounted on a solid, continuous ceiling surface such as drywall, plaster, concrete, or wood. One 3M Command adhesive strip is provided for temporarily mounting and testing the Sensor on smooth, solid ceiling surfaces. This strip is designed for easy, damage-free removal and is not reusable. This strip should not be used for permanently mounting the Sensor (see section G. Permanent Mounting Methods ). Carefully follow the removal instructions below to ensure the ceiling is not damaged during removal. NOTE: DO NOT use the adhesive strip on ceiling tiles, as it will likely cause damage to the tile upon removal. 2.1 Peel the red Command Strips liner off and apply to the at side of the mounting bracket as shown in the diagram. Press rmly. NOTE: DO NOT cover the brackets screw holes because they will be used to mark screw hole locations on the ceiling. NOTE: Leave the removal tab exposed past the edge of the bracket so it can be accessed for removal later. 2.2 2.3 2.4 2.5 2.6 3 3.1 Identify a location on the ceiling where the Sensor will have a good view of the room. Remove the black wall side liner from the adhesive strip. Position the mounting bracket on a clean, dry, dust-free ceiling and press rmly for several seconds. Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise direction until the Sensor locks into place. Perform the Sensor coverage and wireless communication tests as described in sections E. Testing Sensor Coverage and F. Testing Wireless Communication. Removing Temporary Mounting Strip Remove the Sensor from the mounting bracket by twisting in a counter-clockwise direction. If the Sensor coverage and wireless communication tests have been successfully completed, use the mounting bracket as a template to mark the screw hole locations with a pencil. 3.2 To remove the bracket from the ceiling, grasp the removal tab on the adhesive strip and pull the tab VERY SLOWLY straight across the ceiling, stretching the strip until the bracket releases from the ceiling. Discard the strip. NEVER pull the strip at an angle, as it may break or damage the ceiling surface. NOTE: Pull very slowly. NOTE: Do not pull at an angle. E Testing Sensor Coverage 1 With the Sensor mounted on the ceiling, press and release the Test: Sensor button on the front of the device. The lens will glow brie y, indicating the test mode has been entered. NOTE: There is a warm-up period of approximately 90 seconds after the batteries are installed before the test mode can be activated. If the button is pressed during this time, the lens will ash continuously until the warm-up period is complete, and then the test mode will be automatically entered. 2 3 4 5 F 1 2 3 Con rm the coverage area by walking through the space and observing the lens. The lens will glow solid every time motion is detected. If the lens remains off during motion, the Sensor cannot detect motion at that location. Press and release the Test: Sensor button again to exit the test mode. If the button is not pressed, the test mode will automatically time out 15 minutes after being enabled, or 5 minutes after the last detected motion if the room is vacated. If the Sensor has signi cant trouble detecting motion during the test, it should be moved to another location and retested. If the Sensor still has poor detection from the new location, refer to the Troubleshooting section. NOTE: If the Sensor is detecting motion in areas that are not desirable, such as hallways or adjacent rooms, refer to section I. Lens Masking. If Sensor detection is satisfactory during this test, perform the wireless communication test as described in section F. Testing Wireless Communication. Testing Wireless Communication This test should be performed to verify that the Sensor has been correctly set up with the corresponding dimming or switching device and that there is proper wireless communication from the chosen Sensor location. If the lights in the room are not on, turn them ON manually at the dimming or switching device. Press and release the Lights Off button on the front of the Sensor. The lights should turn OFF. Press and release the Lights On button on the front of the Sensor. The lights should turn ON. If the lights do not respond correctly, refer to the Troubleshooting section. G 1 1.1 1.2 2 2.1 2.2 2.3 2.4 Permanent Mounting Methods Permanent Mounting: Drop Ceiling After the Sensor has been temporarily mounted, leave the Sensor in place on the tile and either take the tile down or remove an adjacent tile to gain access to the legs of the mounting wire on the back of the tile. Twist the wire legs together tightly so the mounting bracket remains snug against the tile. Then replace the tile. Permanent Mounting: Solid Ceiling Drill two 3/16 in (4.6 mm) pilot holes for the provided screw anchors. Press the anchors into the holes and tap ush with a hammer. Place the at side of the mounting bracket against the ceiling and install the two provided screws using a hand screwdriver. NOTE: Do not over-tighten. Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise direction until the Sensor locks into place. H Advanced Set-Up (Optional) The Sensor features several advanced set-up modes. For the majority of installations, the default settings will provide the best performance and you will not need to utilize the advanced set-up. The Occupancy version of the Sensor has three adjustable advanced set-up modes:
Timeout, Auto-On, and Activity. The Vacancy-Only version has only two modes
(Auto-On not available). The default settings are listed below. I Default Settings:
Timeout 30 min 15 min 5 min Auto-On Always Low light Disable Activity Timeout: 15 minutes Auto-On: Always (Occupancy version only) Activity:
Low Activity Advanced Set-Up Modes Timeout The Sensor will turn the lights off if no motion occurs for the duration of the timeout period. There are four available timeout settings: 1, 5, 15, and 30 minutes. Auto-On (Occupancy version only) The automatic-on functionality of the Sensor can be adjusted to control how the lights respond upon initial occupancy. There are three available settings: Always, Low light, and Disable. Always: The lights will always turn on. Low light: The lights will only turn on automatically upon entry if there is not already suf cient ambient light in the room. Disable: This setting converts the Sensor to vacancy mode. The lights will not automatically turn on but will still automatically turn off after vacancy. The lights must be manually turned on by using the associated dimming or switching device. NOTE: The 15-second vacancy grace period is active in this mode. Refer to the Sensor Operation section at the beginning of this document for more details. Activity The sensitivity of the Sensor can be adjusted based on the expected level of activity within the room. There are three available activity settings: Low Activity, Medium Activity, and High Activity. Low Activity: This is the most sensitive setting and will detect very slight motions. This is the recommended setting, as it will work well for nearly all applications. It is ideal for spaces where occupants will often be seated for long periods of time. Medium Activity*: This setting is slightly less sensitive than the Low Activity setting and can be used for spaces that experience normal activity. High Activity*: This is the least sensitive setting and can be used for spaces that will generally only experience large motions, such as foot traf c.
* The Low Activity setting is the default and will perform best for most applications. Rarely, if the Sensor is placed near external noise sources such as heating vents, air conditioning vents, or light bulbs, it may turn the lights on without occupancy or keep the lights on too long after vacancy. If this occurs, changing the sensitivity to Medium Activity or High Activity should resolve the problem. Advanced Set-Up Operation The advanced set-up is accessed by using the buttons on the back of the Sensor. Check Settings To display the current setting, press and release the desired button. An LED will illuminate brie y, indicating the current setting. Change Settings The standard settings for Timeout, Auto-On, and Activity are changed using the procedure described below in the left column. The procedure for selecting a 1-minute timeout is slightly different and described below in the right column. Standard Modes 1 To adjust a setting, press and hold the desired button until the LED corresponding to the current setting begins ashing rapidly, indicating the setting can now be adjusted. 2 Each subsequent button press of less than 2 seconds will increment to the next available setting. Pressing any of the other buttons will have no effect. 3 To save the selected setting, press and hold the button until the LED turns on solid. This indicates the saved setting. 1-Minute Timeout*
1 To select a 1-minute timeout, press and hold the timeout button for approximately 10 seconds until all 3 LEDs begin ashing rapidly. 2 To save the 1-minute timeout setting, press and hold the timeout button until all 3 LEDs turn on solid, indicating the 1-minute timeout has been saved.
* The 1-minute timeout is intended for use in high-
activity, brie y occupied areas only (e.g., closet, laundry room, etc.). Do not use this setting in areas that experience minor motion or extended occupancy
(e.g., of ce, bathroom, etc.), as the lights may unexpectedly turn off. Lens Masking (Optional) Whenever possible, the Sensor should be installed in a location where it cannot easily see into areas outside the intended space, such as hallways or adjacent rooms. If this situation cannot be avoided, portions of the lens may be masked with the provided labels to block the Sensors view of the undesired areas. Note: Apply mask to outside of lens only; do not disassemble sensor. It is recommended to remove the Sensor from the mounting bracket before applying the masking labels. NOTE: The Sensor can be screwed onto the mounting bracket in several different orientations. Be sure to note the Sensors orientation before taking it down and replace the Sensor in the same orientation to ensure the intended area gets blocked. Outer lens sections correspond to the detection regions furthest away from the Sensor, while inner sections correspond to regions closer to the Sensor. Be careful when applying the labels to avoid creating gaps between adjacent masked sections. The Sensor may detect motion through inadvertent gaps. Lens sections shown in white are masked with labels Lens Mask Lens sections shown in gray have not been masked Hallway falls within Sensors coverage area. Troubleshooting Symptom Lights do not turn ON when space is occupied. Lights turn OFF while space is occupied. Lights stay ON after space is vacated. Lights turn ON when walking past room. Behavior of lights does not match Sensor settings. Sensor lens does not glow in response to motion during Sensor coverage testing. Lens does not stop glowing during Sensor coverage testing even when there is no motion. Lights do not respond correctly during wireless communication testing. Sensor lens ashes and lights do not turn ON when space is occupied. Possible Causes Solution Sensor is not correctly added to dimming / switching device(s). Sensors Auto-On setting is set to Low light or Disable. The lights were recently turned off manually and the timeout has not yet expired. Sensor does not have full view of room. Sensor is outside wireless range of dimming/switching device. Battery has been installed incorrectly. Dimming/switching device has been improperly wired. Light bulb(s) burned out. Breaker is off or tripped. Sensors timeout is too short for this application. Sensor does not have full view of room. Lens mask is improperly applied. Sensors activity setting is too low. Sensors timeout has not yet expired. An external noise source such as an HVAC vent is interfering. Battery has been installed incorrectly. Sensor coverage extends beyond room perimeter. The intended setting was not saved. Multiple Sensors are added to a dimming/switching device and their settings do not match. Sensor cannot see motion due to obstruction. Room is too big or oddly shaped. Battery has been installed incorrectly. An external noise source such as an HVAC vent is interfering. Sensor is not correctly added to dimming / switching device. Sensor is outside wireless range of dimming/switching device. Battery has been installed incorrectly. Dimming/switching device has been improperly wired. Light bulb(s) burned out. Breaker is off or tripped. Battery is low. Sensor is in test mode. Refer to section B. Set-Up. Refer to section H. Advanced Set-Up. For more details, refer to Frequently Asked Questions at www.lutron.com/occsensors Refer to section C. Sensor Placement and Coverage. Refer to section C. Sensor Placement and Coverage or F. Testing Wireless Communication. Refer to section A. Pre-Installation. Refer to the instruction sheet of the receiving device or call Lutron Technical Support Center at 800.523.9466. Refer to section H. Advanced Set-Up. Refer to section C. Sensor Placement and Coverage. Refer to section I. Lens Masking. Refer to section H. Advanced Set-Up. Refer to section H. Advanced Set-Up. Try moving Sensor to a new location or reducing sensitivity. Refer to section C. Sensor Placement and Coverage or H. Advanced Set-Up. Refer to section A. Pre-Installation. Refer to section C. Sensor Placement and Coverage or I. Lens Masking. Refer to section H. Advanced Set-Up. Refer to section H. Advanced Set-Up. Move Sensor to another location. Refer to section C. Sensor Placement and Coverage. Multiple Sensors may be necessary for full room coverage. For more details, refer to Frequently Asked Questions at www.lutron.com/occsensors Refer to section A. Pre-Installation. Try moving Sensor to a new location or reducing sensitivity. Refer to section C. Sensor Placement and Coverage or H. Advanced Set-Up. Refer to section B. Set-Up. Move Sensor closer to dimming/switching device and retry test. Refer to section F. Testing Wireless Communication. Refer to section A. Pre-Installation. Refer to the instruction sheet of the receiving device or call Lutron Technical Support Center at 800.523.9466. Replace battery. For more details, refer to Frequently Asked Questions at www.lutron.com/occsensors Remove sensor from test mode. Refer to section E. Testing Sensor Coverage.
1 | User Manual (additional) | Users Manual | 852.95 KiB |
Radio Powr SavrTM Wireless Occupancy and Vacancy Sensors 369432 Rev A 1 04.08.11 Wireless Ceiling Mount Sensor Lutrons ceiling-mounted occupancy/vacancy sensors are wireless, battery-powered passive infrared (PIR) sensors that automatically control lights via RF communication to compatible dimming and switching devices. These sensors detect the heat from people moving within an area to determine when the space is occupied. The sensors then wirelessly transmit the appropriate commands to the associated dimming and switching devices to turn the lights on or off automatically. They combine both convenience and exceptional energy savings along with ease of installation. Features Wireless occupancy sensor has 3 settings available:
Auto-On/Auto-Off, Auto-On Low-Light/Auto-Off, and Manual-On/Auto-Off Auto-On Low-Light feature will only turn lights on automatically if there is less than approximately 1 fc
(10 lux) of ambient light Vacancy model available to meet CA Title 24 requirements 10-year battery life design Passive infrared motion detection with exclusive Lutron XCTTM Technology for fine motion detection 360 coverage ranges from 324 sq ft (98 m() to 676 sq ft
(206 m() (depending on mounting height) Multiple ceiling-mount methods available for different ceiling materials RoHS compliant Simple and intuitive adjustments available for Timeout, Auto-On, and Activity settings Front accessible test buttons make setup easy Lens illuminates during test mode to verify ideal locations Multiple sensors can be added for extended coverage refer to product specification submittal of receiving device to determine system limits Models Available:
LRF2-OCR2B-P-WH*
434 MHz Occupancy/Vacancy Sensor LRF2-VCR2B-P-WH*
434 MHz Vacancy Sensor
*WH (white) Compatible RF Devices:
For use with Lutron products only Communicates to the following wireless Lutron systems:
- Maestro Wireless (MRF2)
- GRAFIK Eye QS Wireless
- Energi Savr NodeTM QS (with QS Sensor Module on QS Link)
- Quantum (with QS Sensor Module on QS Link)
- RadioRA 2
- HomeWorks QS S p e c i f i c at i o n S u b m i t ta l Job Name:
Model Numbers:
page Job Number:
Radio Powr SavrTM Specifications Standards FCC certified IC certified COFETEL certified RoHS compliant Environment Temperature: 32 F to 104 F (0 C to 40 C) For indoor use only Power Operating voltage: 3 V-
Operating current: 14 A nominal Requires one CR 123 lithium battery 10-year battery life design Non-volatile memory (saved changes are stored during power loss) Sensor Coverage Test Front accessible test button Lens illuminates orange in response to motion during test mode and is visible from 60 ft (18 m) Wireless Communication Test Front accessible test button Turn loads on and off Dimensions Wireless Occupancy and Vacancy Sensors 369432 Rev A 2 04.08.11 Timeout Options 1 minute *
5 minutes 15 minutes **
30 minutes Auto-On Options (Occupancy Version Only) Always ** - Sensor turns lights ON and OFF auto-
matically. Low light - Sensor turns lights ON automatically only in low ambient light conditions. Sensor turns lights OFF automatically. Disable - Lights must be turned ON manually from dimming or switching device. Sensor turns lights OFF automatically. Activity Options
) Low Activity ** (
Medium Activity (
High Activity (
)
)
** - intended for use in high-activity, briefly occupied areas only
* - default settings 1.13 in
(28.7 mm) 3.57 in
(90.7mm) 2.85 in
(72.4 mm) S p e c i f i c at i o n S u b m i t ta l Job Name:
Model Numbers:
Job Number:
0.887 in
(22.5 mm) page Radio Powr SavrTM Range Diagrams Sensor Coverage with an 8 ft (2.4 m) Ceiling Ceiling Wireless Occupancy and Vacancy Sensors 369432 Rev A 3 04.08.11 8 ft
(2.4 m) Ceiling height Floor 15 ft
(4.6 m) 12 ft
(3.7 m) 9 ft
(2.7 m) 6 ft
(1.8 m) 3 ft
(0.9 m) 0 ft
(0 m) 3 ft
(0.9 m) 6 ft
(1.8 m) 9 ft
(2.7 m) 12 ft
(3.7 m) 15 ft
(4.6 m) Occupant Radius of Coverage at Floor Sensor 18 x 18 ft (5.5 x 5.5 m) Maximum Room Dimensions for Complete Coverage when mounted on an 8 ft (2.4 m) Ceiling 13 ft (4.0 m) Radius of Coverage at Floor when mounted on an 8 ft (2.4 m) Ceiling Sensor Coverage Chart (for sensor mounted in center of room) Ceiling height Maximum room dimensions for complete oor coverage Square feet 8 ft (2.4 m) 9 ft (2.7 m) 18 18 ft (5.5 5.5 m) 324 ft2 (30.2 m2) 20 20 ft (6.1 6.1 m) 400 ft2 (37.2 m2) 10 ft (3.0 m) 22 22 ft (6.7 6.7 m) 484 ft2 (44.9 m2) 12 ft (3.7 m) 26 26 ft (7.9 7.9 m) 676 ft2 (62.4 m2)
* Multiple sensors can be added for extended coveragerefer to product specification submittal of receiving device to determine system limits. S p e c i f i c at i o n S u b m i t ta l Job Name:
Model Numbers:
page Job Number:
Radio Powr SavrTM Wireless Occupancy and Vacancy Sensors 369432 Rev A 4 04.08.11 Installation Overview Sensor Placement The sensors ability to detect motion requires line of sight of room occupants. The sensor must have an unob-
structed view of the room. DO NOT mount behind or near tall cabinets, shelves, hanging fixtures, ceiling fans, etc. The sensor cannot see through glass objects such as patio or shower doors. Hot objects and moving air currents can affect the sensors performance. To ensure proper operation, the sen-
sor should be mounted at least 4 ft (1.2 m) away from light bulbs below the ceiling line and HVAC vents. The sensors performance depends on a temperature differential between the ambient room temperature and that of room occupants. Warmer rooms may reduce the sensors ability to detect occupants. The sensor should be mounted within 60 ft (18 m) line of sight or 30 ft (9.1 m) through walls, of the associated dimming and switching receiving devices. Mounting Mounting of any RF devices on or in close proximity to a metal surface (e.g. directly on fixture with metal housing, metal-backed ceiling tile) will drastically reduce the effective range of radio signal transmission or reception. All RF devices must be mounted on non-conductive materials to ensure proper performance. Temporary mounting is recommended to test sensor coverage and wireless communication before permanently installing the sensor. Drop ceiling (compressed fiber ceiling tile) The ceiling tile mounting wire is provided for both temporary and permanent mounting of the sensor to ceiling tiles. It is designed to allow temporary mounting, testing, and repositioning (if necessary) of the sensor without damaging a ceiling tile. Once the sensors final position has been chosen, the mounting wire should be twisted to lock the sensor in place permanently. Instalacin Espaol Installation English Installing the Ceiling Mount Adapter Cut mounting hole Cut a 3 in to 3 in (76 mm to 76 mm) diameter hole to insert the ceiling mount adapter. the sensor. Solid ceiling (Drywall, plaster, concrete, or Wood) Temporary mounting: One double-sided adhesive strip is provided for temporarily mounting and testing 1 Instalacin del adaptador de montaje en cielo raso Corte un ori cio de montaje Corte un ori cio de 76 mm a 76 mm (3 pulg. a 3 pulg.) de dimetro para insertar el adaptador de montaje en cielo raso. Permanent mounting: Screws and anchors (for drywall or plaster) provided to mount sensor. 3 in to 3 in Recess mount
(76 mm to 76 mm) Ceiling mount clamps internally to ceiling tile. Sensor twist-locks into mount, sits flush with ceiling (as shown below) Opening is 3" in diameter Insert ceiling mount adapter Purchased as a separate kit: LRF-CRMK-WH Insert the ceiling mount adapter into the hole and rotate brackets outwards by turning screws. Inserte el adaptador de montaje en cielo raso Inserte el adaptador de montaje en cielo raso en el ori cio y gire los soportes hacia afuera apretando los tornillos. 76 mm to 76 mm
(3 in to 3 in) 2 Note: No need to access top of ceiling. Nota: No se requiere acceso a la parte su-
perior del cielo raso. Clamp adapter to ceiling S p e c i f i c at i o n S u b m i t ta l 3 Fije el adaptador al cielo raso page Using a Philips screwdriver, hand-tighten the brackets, clamping the adapter to the ceiling. Do not overtighten. Model Numbers:
Job Name:
Utilice un destornillador Phillips para ajustar a mano los soportes y jar el adaptador al cielo raso. No ajuste demasiado. Job Number:
Radio Powr SavrTM Lens Masking Wireless Occupancy and Vacancy Sensors 369432 Rev A 5 04.08.11 Whenever possible, the sensor should be installed in a location where it cannot easily see into areas outside the intended space, such as hallways or adjacent rooms. If this situation cannot be avoided, portions of the lens may be masked with the provided labels to block the sensors view of the undesired areas. Lens sections shown in gray have not been masked Lens sections shown in white are masked with labels Lens label masking sheet S p e c i f i c at i o n S u b m i t ta l Job Name:
Model Numbers:
page Job Number:
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2011-04-20 | 431 ~ 437 | DSC - Part 15 Security/Remote Control Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2011-04-20
|
||||
1 | Applicant's complete, legal business name |
Lutron Electronics Company Inc
|
||||
1 | FCC Registration Number (FRN) |
0006220891
|
||||
1 | Physical Address |
7200 Suter Road
|
||||
1 |
Coopersburg, PA
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@ccsemc.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
JPZ
|
||||
1 | Equipment Product Code |
0079
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
R****** S******
|
||||
1 | Title |
Senior Project Engineer
|
||||
1 | Telephone Number |
610 2********
|
||||
1 | Fax Number |
610 2********
|
||||
1 |
b******@lutron.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Underwriters Laboratories Inc.
|
||||
1 | Name |
B****** D********
|
||||
1 | Physical Address |
1285 Walt Whitman Rd.
|
||||
1 |
Melville, New York 11747
|
|||||
1 |
United States
|
|||||
1 | Telephone Number |
631-5********
|
||||
1 | Fax Number |
631-4********
|
||||
1 |
b******@us.ul.com
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Underwriters Laboratories Inc.
|
||||
1 | Name |
B****** D****
|
||||
1 | Physical Address |
1285 Walt Whitman Rd.
|
||||
1 |
Melville, North Carolina 11747
|
|||||
1 |
United States
|
|||||
1 | Telephone Number |
631-5********
|
||||
1 | Fax Number |
631-4********
|
||||
1 |
b******@us.ul.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSC - Part 15 Security/Remote Control Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Occupancy/Vacancy Sensor | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
UL LLC
|
||||
1 | Name |
B****** D****
|
||||
1 | Telephone Number |
631-2******** Extension:
|
||||
1 | Fax Number |
516-4********
|
||||
1 |
R******@us.ul.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15.231 | 431.00000000 | 437.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC