Sivoia QS Wireless Cellular Shade Automated shade with wireless (RF) control Installation and Programming Guide
(please read before installing) English Start Here 1. Review components 2. Install mounting brackets 3. Install batteries 4. Install the shade in the brackets 5. Removing the shade from the brackets 6. Programming options 5 Removing the shade from the brackets Use a flathead screwdriver to unclip the shade as shown. 1 Review components Included:
e 6 Programming Mounting brackets Endcaps Mounting screws Cellular shade Batteries not included Rechargable batteries Tools required:
Phillips-head screwdriver Cordless drill
(optional) RadioRA 2 For assignment and programming without RadioRA 2 design and programming software, refer to the RadioRA 2 setup guide, available at www.lutron.com/radiora2 Otherwise, use the RadioRA 2 Essentials or Inclusive software to assign and program your cellular shades. e HomeWorks QS Use the HomeWorks QS design and programming software to assign and program your cellular shades. Standalone Proceed to steps 7 and 8 to assign and program your cellular shades with standalone controls. 2 Install mounting brackets 7 Assigning controls Mount the left and right brackets 2 inches in from each end of the shade. Note: Mount additional brackets evenly between the end brackets and clear of the cord lift. Inside mount Outside mount Open Preset Close or 7.1 Enter shade setup mode:
LED Tap shade button -
shade LED turns on solid green 7.2 Assign control:
Hold Close (6 seconds) Close Open 3 Install batteries Shade LED blinks for 2 seconds Open Refer to the battery holders for proper battery alignment. Preset Close 4 Install the shade in the brackets Open Preset Click the shade into place as shown below. Close Open Close Open Close Side view Open Close Open Close Open Close Open Preset Close Open Preset Close Open Close Open Close Open Close Open Preset Close Open Preset Close 8 Set the limits Note: Shade limits must either be set with a Pico or with RadioRA2 or Homeworks QS design and programming software. 8.1 Enter shade setup mode:
Tap shade button - Shade LED turns on solid green e 8.2 Enter limit setup mode:
e Hold Open AND Raise (3 seconds) FCC Information Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/
TV technician for help. Shade LED blinks for 2 seconds, then remains on. 8.3 Adjust limits:
Press Raise or Lower Shade LED remains on solid green. Open Close Open Close 8.4 Save and exit:
To set the upper limit: Hold Open (6 seconds) To set the lower limit: Hold Close (6 seconds) Close Open Shade LED blinks for 2 seconds, then turns off. Open Close Open Close 9 Restore factory defaults (optional) Tap 3 times, hold 3 seconds, tap 3 times. Open Close Open Preset Close Open Preset Close Open Preset Close Open Preset Close Open Note:
Changes or modifications not expressly approved by Lutron Electronics Co. could void the users authority to operate this equipment.
* This device complies with Part 15 of the Preset Close Open Close FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful Open Close interference and
(2) This device must accept any Open Preset interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Close Open Close Open Close For more information:
www.lutron.com/
technicaldocumentlibrary/
window%20systems%20 warranty.pdf Open Close Contact the Lutron Technical Support Center at the numbers provided below or your local Lutron sales representative with questions concerning the installation or operation of the System or this Warranty, or to make a warranty claim. Please provide the exact model number when calling. Close Open or Open Preset Close Open Preset Close Open Preset Close Open Preset Close Shade LED blinks for 2 seconds after hold, then for 5 seconds after second triple-tap. Troubleshooting Open Preset Symptom Open Close Preset Close or or 10 Open Close Open Close Shade does not go all the way down Open Preset Close Open Preset Close Shade hangs unevenly Open Close Open Preset Close Open Limited warranty Preset Solution Fabric needs to relax
(close shade for 24 hours then reset the lower limit) Reset the lower limit Ensure that fabric is not pinched in the mounting brackets Close Number of years from date of shipment Percentage of cost of replacement parts credited by Lutron Up to 5 More than 5 but not more than 8 More than 8 100%
50%
0%
Lutron, the Sunburst logo, Sivoia, RadioRA, HomeWorks, and Pico are registered trademarks of Lutron Electronics Co., Inc. Worldwide Headquarters | USA Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 USA TEL: 1.610.282.3800 FAX: 1.610.282.3090 Technical Support:
1.800.523.9466 or 1.610.282.6701 Toll Free: 1.888.LUTRON EMAIL: shadinginfo@lutron.com WEB: www.lutron.com/
shadingsolutions Europe Headquarters |
United Kingdom Lutron EA Ltd 6 Sovereign Close London, E1W 3JF, UK TEL: +44.(0)20.7702.0657 FAX: +44.(0)20.7480.6899 Technical Support: +44.
(0)20.7480.6899 FREEPHONE: 0800.282.107 Asian Headquarters |
Singapore Lutron GL Ltd 15 Hoe Chiang Road
#07-03 Singapore, 089316 TEL: +65.6220.4666 FAX: +65.6220.4333 Technical Support: 800.120.4491 2011 LUTRON Electronics Co., Inc. P/N 045-355 REV. A