Installing your dimmer 1 Turn power off at circuit breaker!
2 Remove existing switch from wall Installation for lights with one wall switch (single pole) Remove the switch and pull it away from the wall. Do not remove outside side sections on dimmers at the end of gang. N O N O F F O F F O WARNING: SHOCK HAZARD May result in serious injury or death. Turn off power at circuit breaker or fuse before installing. Remove the wallplate from switch. 1 2 3 4 Disconnect all three wires* from the switch. 5 6 Ground 7 Important note:
Some lights have one wall switch, while others have two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). Weve included instructions for lights with one wall switch (called a single pole). If your light has more than one switch (called a 3-way), please visit www.casetawireless.com/3way for complete installation instructions and how-to videos. 3 Remove side sections (if necessary) 4 Connect the dimmer Bend back and forth. 3 2 1 Ground 1 Connect the bare copper (or green) ground wire from the wallbox to the green wire on the dimmer using a wire connector. 2 Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector. 3 Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector. Each dimmer has inside side sections removed. Dimmer at middle has all side sections removed. Important note:
Removing side sections reduces the dimmers maximum wattage rating. See the chart below for maximum wattage information. Maximum* wattage derating chart
(120 V~ 50/60 Hz) Side sections removed None 1 side 2 sides LED & CFL 150 W 150 W 150 W or*
Incandescent &
Halogen 600 W 500 W 400 W 5 Mount the dimmer Use the screws provided. 1 2 6 Attach the wallplate Attach the adapter to the dimmer using the screws provided and snap on the wallplate. 1 2 3 snap
(If you installed the dimmer next to other dimmers or switches, youll need to install a wallplate with the correct size/number of openings to accommodate all the devices.) 7 Turn power on at circuit breaker N O N O F F O F F O CAUTION Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent,lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances. Codes Install in accordance with all national and local electrical codes. Grounding When no grounding means exist in wallbox, the National Electrical Code (NEC) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox. FCC/IC Information This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Informations FCC/IC Cet appareil est conforme la partie 15 des rgles de la FCC et des standards CNR exempt de licence d'Industrie Canada. Le fonctionnement est sous rserve des deux conditions suivantes : (1) Cet appareil ne doit pas provoquer dinterfrence. (2) Cet appareil doit accepter toutes les interfrences, y compris les interfrences qui pourraient provoquer un fonctionnement indsirable. Les modifications qui nont pas t expressment approuves par Lutron Electronics Co., Inc. peuvent annuler le pouvoir de lutilisateur dutiliser cet quipement. REMARQUE : Cet quipement a t test et est conforme aux limites dun appareil numrique de Classe B en vertu de la partie 15 des rgles de la FCC. Ces limites sont conues pour fournir une protection raisonnable face aux interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre une nergie de frquence radio et, sil nest pas install et utilis conformment aux instructions, il peut provoquer des interfrences nuisibles aux communications radio. Cependant, il ny a aucune garantie que des interfrences ne surviendront dans une installation particulire. Si cet quipement provoque des interfrences nuisibles pour la rception radio et tlvisuelle, ce qui peut tre dtermin en allumant et en teignant lquipement, il est recommand que lutilisateur tente de corriger ces interfrences en utilisant une ou plusieurs des mesures suivantes :
- Rorientez ou repositionnez lantenne rceptrice
- Augmentez la sparation entre lquipement et le rcepteur
- Connectez lquipement une prise lectrique se trouvant sur un circuit diffrent de celui o le rcepteur est connect
- Demandez laide du vendeur ou dun technicien radio/TV expriment Cet appareil numrique de classe B est conforme la norme ICES-003 du Canada. Phillips-head screwdriver Ground P/N 0302038 REV A
* If your switch has more than 3 wires attached, see Installing Casta Wireless in a 3-way switch application video at www.casetawireless.com/3way
* For maximum wattage information when mixing light bulb types see www.casetawireless.com/ganging Works with energy efficient dimmable light bulbs:
Using your Casta Wireless kit (sold separately) With a smartphone or tablet (Bridge required, sold separately) Without a smartphone or tablet (Bridge not required) Using your controls Warranty For warranty information, please visit www.casetawireless.com/warranty The CastaT Wireless dimmer can be controlled from a smartphone when used with the Lutron Smart Bridge. If you are using the dimmer and remote control with the Lutron Smart Bridge follow the instructions below. Note: If you are using the dimmer and remote control with another manufacturers bridge, please refer to that manufacturers instructions for set-up. 1 Press and hold off button on dimmer Download the Lutron app Search for Lutron Caseta Pairing the dimmer and Pico remote control 1 Press and hold off button on dimmer Lutron Lutron Smart Bridge Lutron app Hold for 6 seconds until LEDs start blinking Changing the favorite light level on the Pico remote control
(sold separately) You can use the round favorite button on the Pico remote control to recall a favorite light level. Weve set it to 50%, but you can change it to any level you like. Favorite 3 Set desired light level on dimmer In-wall dimmer On Darker Off FASS Front Accessible Service Switch Troubleshooting Symptoms Light does not turn on or in-wall dimmer LEDs do not light up. Light does not respond to Pico remote control. www.casetawireless.com/LutronApp Lutron 2 Press and hold off button on remote Launch the Lutron app 2 Press and hold off button on remote Hold for 6 seconds until lights flash 3 times. Lutron The Lutron app will walk you through setting up your devices. x3 4 Press and hold favorite button on remote Replacing light bulbs using FASS Pull the FASS switch out on the in-wall dimmer to remove power at the light socket. Brighter On Favorite Darker Off 3 Press and hold off button on remote Use the Lutron app to complete ALL remaining steps Add devices Pico remotes Dimmers Shades Control three ways Schedule your lights Connect while away Repeat steps to pair other Pico remote controls. Hold for 6 seconds until LEDs blink twice on in-wall dimmer. New favorite level is now saved. Pico remote control (sold separately) Important notes:
1. For indoor use only. 2. Operate between 32 F (0 C) and 104 F (40 C). x2 For advanced features, tips for using CastaTM Wireless dimmers with CFLs and LEDs, the complete CastaTM Wireless product line, and more, please visit www.casetawireless.com/features Device Ratings In-wall dimmer DS-6WCL 120 V~ 50/60 Hz Wireless quick-start guide In-wall dimmer Welcomeand thank you for purchasing a Casta Wireless in-wall dimmer. In order to control your lights from an app or remote, youll need to replace an existing switch with a Casta Wireless in-wall dimmer. Before you install the dimmer, please watch the installation video at www.casetawireless.com/support We hope you enjoy the convenience of Casta Wireless!
Double your warranty Love Casta Wireless dimmers? Have ideas for making them better? Tell us what you think and well extend your warranty by 1 year. www.casetawireless.com/register Contents supplied In-wall dimmer
(DS-6WCL) Wire connectors (3) Screws (2) Tools youll need Flat-head screwdriver Pliers LEDup to 150 W CFLup to 150 W Halogenup to 600 W Incandescentup to 600 W NOTE: You can mix and match dimmable LED and CFLs, as well as halogen and incandescent light bulbs, with Casta Wireless dimmers. Dimmable LED and CFL light bulbs vary in their dimming performance. If youre using these bulbs and they flicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance. For a complete list of compatible dimmable LEDs and CFLs, please visit www.casetawireless.com/bulblist Compatible light bulbs include:
Cree BA19-08027OMF-12DE26-1U100 CR6-575L EcoSmart ECS BR30 W27 FL 120 ECS 20 WW FL 50WE 120 Feit A19/OM/LED Philips 9290002295 Sylvania LED12A19/DIM/O/827 LED21PAR38/DIM/P/930/FL30 Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. Probable cause and action Light bulb(s) burned out. Breaker is OFF or tripped. Light not properly installed. Wiring error. FASS switch on the dimmer is in the Off position. The dimmer failed to pair with Pico remote control; see Pairing the dimmer and Pico remote control. The dimmer is already at the light level the Pico remote control is sending. The Pico remote control is outside the 30 ft (9 m) operating range. The Pico remote control battery is low. The Pico remote control battery is installed incorrectly. Verify bulbs are marked dimmable and visit www.casetawireless.com/
lowend for information on adjusting the dimmer for best bulb performance. Bulbs turn off while being dimmed. Bulbs turn on at high light level but do not turn on at a low light level. Bulbs flicker or flash when dimmed to a low light level. Go to www.casetawirless.com/support for additional troubleshooting suggestions. Lutron, the Lutron logo, FASS, Casta, Smart Bridge and Pico are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. All other product names, logos, and brands are property of their respective owners. 2021 Lutron Electronics Co., Inc P/N 0302038 REV A