FCC ID: JPZ0140 Smart Switch

Installation for lights with one wall switch (single-pole) Wireless quick-start guide Installing your switch 1 Turn power off at circuit breaker!

In-wall switch Welcomeand thank you for purchasing a Casta Wireless Diva Smart in-wall switch. In order to control your lights from an app or remote, youll need to replace an existing switch with a Casta Wireless Diva Smart in-wall switch. We hope you enjoy the convenience of Casta Wireless!

N O N O F F O F F O P/N 0302039 REV A WARNING: SHOCK HAZARD May result in serious injury or death. Turn off power at circuit breaker or fuse before installing. 2 Remove existing switch from wall Remove the wallplate from switch. 1 2 Remove the switch and pull it away from the wall. Double your warranty Love Casta Wireless products? Have ideas for making them better? Tell us what you think and well extend your warranty by 1 year. www.casetawireless.com/register Contents supplied In-wall switch

(DS-5ANS, DVRF-5NS) Jumper wire Wire connectors (5) Screws (2) Tools youll need Flat-head screwdriver Pliers Phillips-head screwdriver Contractor note:

For wiring diagrams, please visit www.casetawireless.com/wiring 3 4 Important note:

Some lights have one wall switch, while others have two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). Weve included instructions for lights with one wall switch

(called a single pole). If your light has more than one switch (called a 3-way), please visit www.casetawireless.com/3way for complete installation instructions and how-to videos. Disconnect all three wires* from the switch. 5 6 Ground 7 Note the hot and load wires Neutral connection required Ground

* If your light has more than one switch (called a 3-way), please visit www.casetawireless.com/3way 3 Ganging and Derating Double Gang Triple Gang 4 Connect the switch 6 Attach the wallplate Attach the adapter to the switch using the screws provided and snap on the wallplate. Important note:

Removing side sections does not reduce the switchs maximum wattage rating. See the chart below for maximum load information. Maximum load derating chart (120 V~ 50/60 Hz) Model Load Type DS-5ANS LED, & Fluorescent 1 DS-5ANS Incandescent, Halogen, & ELV Single gang Double gang Triple gang 5 A 5 A 5 A or 600 W 600 W 600 W or DS-5ANS MLV 2 600 VA 600 VA 600 VA DS-5ANS General Purpose Fan or 3 A 3 A 3 A 1 The in-wall switch is ULR Listed for use with all magnetic and electronic fluorescent ballasts. 2 The maximum lamp wattage is determined by the efficiency of the transformer, with 70%85% as typical. For actual transformer efficiency, contact either the fixture or transformer manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of the in-wall switch. 3 2 4 1 Ground 1 Connect the bare copper (or green) ground wire from the wallbox to the green wire on the switch using a wire connector. 2 Connect the load wire from the wallbox to the red wire on the switch using a wire connector. 3 Connect the hot wire from the wallbox to the black wire on the switch using a wire connector. 4 Connect the neutral wire from the wallbox to the white wire on the switch (neutral connection required). 1 2 3 snap

(If you installed the switch next to other switches or dimmers, youll need to install a wallplate with the correct size/number of openings to accommodate all the devices.) 7 Turn power on at circuit breaker N O N O F F O F F O 5 Mount the switch Use the screws provided. 1 2 CAUTION Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent,lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances. Codes Install in accordance with all national and local electrical codes. Grounding When no grounding means exist in wallbox, the National Electrical Code (NEC) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox. FCC/IC Information This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Informations FCC/IC Cet appareil est conforme la partie 15 des rgles de la FCC et des standards CNR exempt de licence d'Industrie Canada. Le fonctionnement est sous rserve des deux conditions suivantes : (1) Cet appareil ne doit pas provoquer dinterfrence. (2) Cet appareil doit accepter toutes les interfrences, y compris les interfrences qui pourraient provoquer un fonctionnement indsirable. Les modifications qui nont pas t expressment approuves par Lutron Electronics Co., Inc. peuvent annuler le pouvoir de lutilisateur dutiliser cet quipement. REMARQUE : Cet quipement a t test et est conforme aux limites dun appareil numrique de Classe B en vertu de la partie 15 des rgles de la FCC. Ces limites sont conues pour fournir une protection raisonnable face aux interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre une nergie de frquence radio et, sil nest pas install et utilis conformment aux instructions, il peut provoquer des interfrences nuisibles aux communications radio. Cependant, il ny a aucune garantie que des interfrences ne surviendront dans une installation particulire. Si cet quipement provoque des interfrences nuisibles pour la rception radio et tlvisuelle, ce qui peut tre dtermin en allumant et en teignant lquipement, il est recommand que lutilisateur tente de corriger ces interfrences en utilisant une ou plusieurs des mesures suivantes :

- Rorientez ou repositionnez lantenne rceptrice

- Augmentez la sparation entre lquipement et le rcepteur

- Connectez lquipement une prise lectrique se trouvant sur un circuit diffrent de celui o le rcepteur est connect

- Demandez laide du vendeur ou dun technicien radio/TV expriment Cet appareil numrique de classe B est conforme la norme ICES-003 du Canada. Supported Loads (120 V~) DS-5ANS LEDup to 5 A Incandescent / Halogenup to 600 W MLVup to 600 VA ELVup to 600 W Fluorescentup to 5 A General Purpose Fanup to 3 A Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. To use your Casta Wireless Diva Smart kit (sold separately) With a smartphone or tablet (Smart Bridge required, sold separately) Without a smartphone or tablet

(Smart Bridge not required) The Casta Wireless Diva Smart switch can be controlled from a smartphone when used with the Lutron Smart Bridge. All devices must be within 30 ft (9 m) from the Lutron Smart Bridge. Using your controls Troubleshooting Symptoms Light does not turn on or in-wall switch LED does not light up. Probable cause and action Red and black wires on the switch are reversed. (See steps 4.2 and 4.3 on the previous page) Lutron Pairing the switch and Pico remote control 1 Press and hold off button on the switch Lutron Smart Bridge Lutron app On Off Hold for 6 seconds until LED starts blinking FASS Front Accessible Service Switch Light does not respond to Pico remote control. In-wall switch Replacing light bulbs using FASS Pull the FASS out on the in-wall switch to remove power at the light socket. Light bulb(s) burned out. Breaker is OFF or tripped. Light not properly installed. Wiring error. FASS on the switch is in the Off position. The switch failed to pair with Pico remote control; see Pairing the switch and Pico remote control. The switch is already at the light level the Pico remote control is sending. The Pico remote control is outside the 30 ft (9 m) operating range. The Pico remote control battery is low. The Pico remote control battery is installed incorrectly. 2 Press and hold off button on remote Hold for 6 seconds until lights flash 3 times. x3 Pico remote control (sold separately) Go to www.casetawireless.com/support for additional troubleshooting suggestions. On Off Repeat steps to pair other Pico remote controls. Important notes:

1. For indoor use only. 2. Operate between 32 F (0 C) and 104 F (40 C). For advanced features, tips for using Casta Wireless products with LEDs, the complete Casta Wireless product line, and more, please visit www.casetawireless.com/features Warranty For warranty information, please visit www.casetawireless.com/warranty Device Ratings In-wall switch DS-5ANS, DVRF-5NS 120 V~ 50/60 Hz Lutron, the Lutron logo, Casta, Diva, FASS, and Pico are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. All other product names, logos, and brands are property of their respective owners. 2022 Lutron Electronics Co., Inc

SECTION 1 -SIZE SIZE OF LABEL:

Width: 0.73 in 2.33 in Lengrth:

FLEXCON PRODUCT INFORMATIO THE.R lLfihn SELECT21940 Description:

Product THERMLfilm SELECT 21940 is a UL-recognized/CSA-accepted, printable, with an aggressive, rel ease liner. white polye ter coated acrylic adhesive, permanent 2.0 mil gloss topcoated and backed with a roll fom1 thermal transfer THERMLfi.lm PM 200 \l, ...................... .............................. 2.0 mil gloss white polyester high-performru1ce label applications. design ed for

Date: March 16, 2022 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Ge. BEC Incorporated 970 E. High Street Pottstown PA 19464 To whom it may concern:

I, the undersigned, hereby authorize BEC Incorporated to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by BEC Incorporated on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. In authorizing BEC Incorporated as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

7200 SUTER ROAD TELEPHONE 610 282-3800 COOPERSBURG, PA 18036-1299 FAX 610 282-3769 LUTRON ....:0::

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

D take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, fo AWe Daniel J. Schlegel Standards Compliance Supervisor Lutron Electronics Co., Inc. 7200 SUTER ROAD TELEPHONE 610 282-3800 COOPERSBURG, PA 18036-1299 FAX 610 282-3769

LUTRON Ji fhilie 7200 SUTER ROAD TELEPHONE 2-3800 COOPERSBURG, PA 18036-1299 FAX 610 282-3769 ELECTRONICS CO., ING roaalaaleralver=it(e)atcmOne) eal aatrctsd(e) a]

7435 Oakland Mills Road Columbia MD 21046 30-Mar-22 Subject: Long Term Request for Confidentiality JPZ0140

|DY=:[mes) mre) mn Viele l= lanl This letter is to formally request long term confidentiality, per the FCC Rules 47 CFR 0.457 rTaXe MOM Solo Mm Co) maal=]icler-licmelmmlalioliner-lielamvelelsaliic-ve mcomial-MOxelanalcs1(elamomel-M UI =)emIKelan ed0]e) (om abj el-xeut(e) a For all models in this submission, the following items are Lutron Electronics Co., Inc. oro) alice(=salirclmiavielsanr=ltce)amar-1mnalet-yaol-mice)tamelele)|(om|atcyel-tei (eam enm ole)(- alii: |mece)ag) ol ih1Ke]E-MCol e) ge) (101 our business. 1. Schematic 2. Operation Description 3. Bill of Materials 4. Block Diagram Siar lal @cele mel cele meee) ere lilel 4) Sincerely, iel J. Sch cS} Flare f=] 0 kM Oxo) an) o]it-larercMolel =a ce) m 610 28

LUTRON ELECTRONICS CO., INC. Communications Commission Federal 7 435 Oakland Columbia MD 21046 Mills Road March 30th

, 2022 Subject:

Short Term Request for Confidentiality-

FCC ID: JPZ0140 Dear Sir or Madam:

This letter and 0.459, public is to formally for materials request or information inspection. short term confidentiality, per the FCC Rules 47 CFR 0.457 submitted to the Commission from to be withheld Lutron For all models in this submission, information submitted Commission September to the 2022. Electronics be withheld Co., Inc. requests from public or 30th of inspection until that materials Photos 1.Internal 2.External Photos 3.Test Setup Photos 4.User Manual Thank you for your cooperation. Sincerely, D Standards Compliance Supervisor