Installation Instructions Please Read Before Installing Overview The STRD-1B, -2B, -3B,
-3BRL, -4B, -4FS, -4S, -4SIR,
-5B, -5FS, -5BRL, -6B, -6BRL, and -7B keypads are for use with HomeWorks systems. The keypad buttons are pro-
grammed with a personal computer using the HomeWorks Utility. Up to 32 keypads, each with a unique address, can be assigned to each HomeWorks RF Processor. Designer-style RF seeTouchTM Keypads STRD-1B, -2B, -3B, -3BRL, -4B, -4FS, -4S,
-4SIR, -5B, -5FS, -5BRL, -6B, -6BRL, -7B 120 V ~, 50/60 Hz, 0.2 A STRD-1B*
STRD-3BRL*
STRD-3B*
STRD-2B*
STRD-4B*
STRD-4FS*
STRD-4S*
STRD-4SIR*
STRD-5B*
STRD-5FS*
STRD-5BRL*
STRD-6B*
STRD-6BRL*
STRD-7B*
Installation 1. Turn power OFF at fusebox or circuit breaker. Danger - Locate and remove fuse or lock circuit breaker in the OFF position before proceeding. Wiring with power ON may result in personal injury. 2. Prepare wires. When making wire connections, follow the recommended strip lengths and combinations for the sup-
plied wire connectors. Note: Wire connectors provided are suitable for copper wire only. Small:
Strip insulation 3/8 in. (10 mm) for 14 AWG (2.5 mm2). Strip insulation 1/2 in. (13 mm) for 16 AWG (1.5 mm2). Use to join one 14 AWG supply wire with one 16 or 18 AWG (1.0 mm2) control wire. 3. Wiring: See Wiring Diagram. 4. Push all wires back into the wallbox and loosely fasten the control to the wallbox using the keypad mounting screws pro-
vided. Do not pinch the wires. 5. Attach Lutron Claro or Satin Colors wallplate adapter and wallplate. a. Loosely install keypad mounting screws. b. Tighten wallplate adapter mounting screws snug. c. Tighten keypad mounting screws until wallplate adapter is flush to wall (do not over-tighten). d. Snap wallplate onto wallplate adapter, and verify that buttons are not submerged. e. If buttons are submerged, loosen keypad mounting screws appropriately. 6. Restore power. Small
* Wallplate/Adapter purchased separately. Important Notes Codes: Install in accordance with all local and national electri-
cal codes. Environment: Ambient operating temperature:
0-40C, 32-104F, 0-90% humidity, non-condensing. Indoor use only. Wallplates: Lutron Claro and Satin ColorsTM wallplates are rec-
ommended for best color match and clean aesthetic appear-
ance. Do not paint controls or wallplates. Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning solutions. Wallboxes: Lutron recommends using 3-1/2 in. (89 mm) deep wallboxes for easier installation. RF Device Placement: RF Keypads must be located within 30 ft. (9 m) of an RF Signal Repeater or an RF Processor. RF Keypads will not function until they are addressed and pro-
grammed using the HomeWorks Utility. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 Made and printed in the U.S.A. 02/03 P/N 043-146 Rev. A Mounting Diagram Wiring Diagram Keypad Mounting Screws Button Kit Adapter Mounting Screws Hot/Live Black 120/127 VAC 50/60 Hz White Wallbox Keypad Neutral Wallplate/Adapter purchased separately. Troubleshooting Guide RF Keypads will not function until they are addressed and pro-
grammed using the HomeWorks Utility. Symptom LEDs don't light up when buttons are pressed. Cause and Action Power not present at keypad Circuit breaker OFF. Turn ON breaker. Wiring error. Check wiring to be sure it agrees with installation instructions. Button presses on keypad cause the key-
pad to quickly flash all its LEDs simultane-
ously. Keypad has not been addressed. Address the keypads using the HomeWorks Utility. Button presses on keypad cause the key-
pad to slowly flash all its LEDs simultane-
ously. Keypad has an address, but has not had programming uploaded. Upload to the system using the HomeWorks Utility. Keypad cannot be addressed. Keypad is out of RF communications range. LEDs light when button is pressed, but the system response is not correct. Move RF Signal Repeater or RF Processor to within 30 feet (9 m) of key-
pad. Improper programming Check programming in HomeWorks Utility. Technical and Sales Assistance If you need assistance, call the toll-free Lutron Technical Support Center. Please provide exact model number when calling.
(800) 523-9466 (U.S.A., Canada and the Caribbean) Other countries call:
Tel:
Fax:
Visit our Web site at www.lutron.com
(610) 282-3800
(610) 282-3090 FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the seperation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the users authority to operate this equipment. LIMITED WARRANTY Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within two years after purchase. For warranty serv-
ice, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. After the two year period, a pro-rated warranty applies to this product until eight years after the purchase. For more information regarding this warranty contact your Lutron representative. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIM-
ITED TO TWO YEARS FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REIN-
STALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROP-
ER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRONS LIA-
BILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limita-
tions on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. These products may be covered under one or more of the following U.S. patents: 4,835,343; 4,889,999; 5,170,068; 5,237,207; 5,736,965;
5,838,226; 5,848,054; 5,905,442; 5,982,103; D436,930; D453,742; D456,783; D461,782; D465,460; D465,770; D466,090; D466,091; D466,484 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, Claro and HomeWorks are registered trademarks and Satin Colors, seeTouch and the HomeWorks Logo are trademarks of Lutron Electronics Co., Inc. 2003 Lutron Electronics Co., Inc.