FCC ID: JPZ0134 Wireless Dimmer

1 Turn power OFF at circuit breaker 2 Determine wiring configuration Please read before installing. English English N O F F O Dimmer Dimmer 120 V~ 50 / 60 Hz 2A For lights controlled from one location:

Dimmer Fully wrap the wires around the screw and tighten (A), or strip insulated wires to 1/2 in (13 mm) and insert into the push-in terminals (B). Solid copper wire only. WARNING: ELECTRIC SHOCK HAZARD. May result in Serious Injury or Death. Turn off power at circuit breaker or fuse before installing. IMPORTANT 1. CAUTION: Use only with permanently installed fixtures with dimmable screw-in LED, dimmable self-ballasted compact fluorescent, halogen, or incandescent lamps. Use only to control the primary side of permanently installed transformer supplied low-voltage lighting, or in combination with incandescent lamps. To reduce the risk of overheating and possible damage to other equipment DO NOT use to control receptacles, fluorescent lighting fixtures, non-ballasted or externally ballasted compact fluorescent lamps, motor operated appliances or transformer supplied appliances. 2. Neutral is required for all load types. 3. Install in accordance with all national and local electrical codes. 4. When no grounding means exist within the wallbox, the NEC 2011, Article 404.9 allows a dimmer without a grounding connection to be installed as a replacement, as long as a plastic, noncombustible wallplate is used. For this type of installation, twist a wire connector onto the green ground wire or remove the green ground wire on the dimmer and use an ap pro pri ate wallplate such as Claro or Satin Colors series wallplates by Lutron. 5. Protect the dimmer from dust and dirt when painting or spackling the wall. 6. This dimmer is not compatible with standard 3-way or 4-way switches. Use only with Lutron companion dimmers listed above. 7. In any 3-way / 4-way circuit use only one dimmer with up to 8. Maximum wire length between the dimmer and the farthest companion 4 companion dimmers. dimmer is 150 ft (45 m). 9. Operate between 32 F and 104 F (0 C and 40 C). 10. It is normal for the dimmers to feel warm to the touch during operation. 11. Clean the dimmer with a soft damp cloth only. Do not use any chemical cleaners. For disinfecting, please refer to App Note #758 (048758), Cleaning Recommendations for Lutron Products at www.lutron.com. 12. For indoor use only. Ground wire

(bare or green) Dimmer Blue Silver Black Brass Green Ground Line / Hot 120 V~

50 / 60 Hz Neutral 2B Brass Neutral Blue Silver Black Load/Light Line/Hot Green wire Ground wire

(bare or green) Load OR 5 in-lbs (0,55 Nm) A 12 / 14 AWG

(2.5 1.5 mm2) OR B 1/2 in

(13 mm) 14 AWG ONLY

(1.5 mm2) For lights controlled from two locations:

NOTE: Dimmer must be wired on the load side. Connect Neutral to the dimmer. Up to four companion dimmers may be used. For additional wiring assistance go to www.lutron.com/wiringwizard NOTE: Only one dimmer can be used per circuit. Different-

colored screw IMPORTANT:

Tag or mark the common wire on both existing devices. This is usually connected to a darker (or different) colored screw than the others. This does NOT include the ground screw. Companion Dimmer

. Brass Blue A Black Marked wire Dimmer Brass Blue Silver A Black Neutral Marked wire Ground wire

(bare or green) Green wire Ground wire

(bare or green) Line/Hot To breaker Load To light Ground wire

(bare or green) Green wire NOTE: Dimmer MUST be on the load side. NOTE: DO NOT install dimmer on the line side. Companion Dimmer Dimmer Dimmer Companion Dimmer Brass Brass Blue Brass Blue Silver Black Brass A Green Ground Green Load Ground Blue Black Line / Hot 120 V~

50 / 60 Hz Neutral Blue Silver Black Line / Hot 120 V~

50 / 60 Hz Neutral Black A Green Ground Green Load Ground OR 2021 Lutron Electronics Co., Inc.

** For more information please go to www.lutron.com/wiringwizard

(continued on next page) 250 W LED / CFL 500 W Inc. / Hal. / ELV 400 VA MLV Companion Dimmer (for 3-way wiring) 120 V~ 50 / 60 Hz 8.3 A Find the right LED lutron.com/LEDfinder Help Use our mobile friendly self-paced installation tool:

www.lutron.com/wiringwizard Find more product information:

www.lutron.com/support

- Videos

- Frequently Asked Questions

- Online Chat (8 am 5 pm EST) Call us:

U.S.A. | Canada | Caribbean 1.844.LUTRON1 (588.7661) (24/7) Mexico

+1.888.235.2910 Others

+1.610.282.3800 www.lutron.com/support Limited Warranty:

www.lutron.com/TechnicalDocumentLibrary/Warranty.pdf For FCC/IC information:

Please visit: www.lutron.com/fcc-ic Lutron, Claro, and Satin Colors are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. All product names, logos, and brands are property of their respective owners. 2C For lights controlled from three or more locations:

NOTE: Dimmer must be wired on the load side. Connect Neutral to the dimmer. Up to four companion dimmers may be used. For additional wiring assistance go to www.lutron.com/wiringwizard NOTE: Only one dimmer can be used per circuit. Companion Dimmer Companion Dimmer Dimmer IMPORTANT:

Tag or mark the common wire on existing 3-way devices. This is usually connected to a darker

(or different) colored screw than the others. This does NOT include the ground screw. A Brass C Blue Black Hot Marked wire Different-

colored screw Ground wire

(bare or green) C D Blue Black Brass B A A Brass Marked wire Neutral B Blue D Silver Line / Hot Black B 120 V~

50 / 60 Hz Neutral Line/Hot To breaker Load To light Ground Ground Ground Green wire Ground wire

(bare or green) Ground wire

(bare or green) Green wire Ground wire

(bare or green) Green wire Companion Dimmer Companion Dimmer Dimmer C D Blue Brass Blue A Brass Brass Black A Black B Blue Silver Black Green Green Green Load 3 Mount all devices using the provided screws and attach wallplate FCC / IC / IFT Information This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron ElectronicsCo., Inc. could void the users authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. The user should avoid prolonged exposure within 7.9 in (20 cm) of the antenna, which may exceed FCC/ISED radio frequency exposure limits. This Class B digital apparatus complies with Canadian ICES-003. 4 Turn power ON at circuit breaker N O F F O

MODEL NUMBER RATINGS Dimmer for permanently installed lighting xtures only Atenuador para luminaries permanentemente instalados Gradateur pour luminaires installs de faon permanente Assembled in Mexico Ensamblado en Mxico Assembl au Mexique USA/CAN: 1.844.LUTRON1 En Mxico: +1.888.235.2910 TF Pat. / Brevets: lutron.com/patents Pat. / Brevets: lutron.com/patents FCC ID: JPZ0134 IC: 2851A-JPZ0134 HVIN: DDM1 a 2 3 6 9 1 0 0 5 50019632 Rev. A 01/2021 Size: 2.30 in x 0.99 in Color: Black Die Cut: Magenta (do not print)

Date: 9/2/2021 UL LLC 12 Laboratory Dr. Research Triangle Park, NC 27709 USA To whom it may concern:

I, the undersigned, hereby authorize UL LLC to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL LLC as our representative, we still recognize that we are responsible to:

a) fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC;

b) supply any and all information needed for the evaluation of the products for which certification is sought;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized;

e) discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification;

f) use certification only to indicate that products are certified in conformity with specified standards;

g) endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety;

h) comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements;

i) comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers;

j) ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements;

k) provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCBs or the FCCs market surveillance requirements;

l) keep a record of all complaints relating to products compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies;

m) inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until further written notice from the applicant. Sincerely Yours, Daniel J. Schlegel Standards Compliance Supervisor Lutron Electronics Co., Inc.

Date: 9/2/2021 Attn: FCC Office of Engineering and Technology / UL Verification Services TCB Subject:

Request for Confidentiality FCC ID:

JPZ0134 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Antenna Specification Model Differences Letter Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until a period of 180 days after the grant date:

External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Daniel J. Schlegel Standards Compliance Supervisor Lutron Electronics Co., Inc.

Date:

8/23/2021 Attn:

FCC Office of Engineering and Technology / UL Verification Services TCB Subject:

Request for Withdrawl of Application FCC ID:

JPZ0134 To Whom It May Concern:

Lutron Electronics Co., Inc. hereby requests for a withdrawl of the FCC Registration Number JPZ0134. Lutron requests this action as the product covered under this Grant has not yet made availible for sale anywhere in the world and has not been sold with the FCC grant assigned. As the product has not been made availible for sale the short-term confidentiality expiration would lead to business sensitive information being made availible to the public before the actual marketing of newly authorized devices Please direct any questions concerning this request to the technical Contact Daniel J Osle dosle@lutron.com or (610) 282- 7867 for further information. Best Regards, Daniel J. Schlegel Standards Compliance Supervisor Lutron Electronics Co., Inc.

Date: 2/12/2021 UL LLC 12 Laboratory Dr. Research Triangle Park, NC 27709 USA To whom it may concern:

I, the undersigned, hereby authorize UL LLC to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL LLC as our representative, we still recognize that we are responsible to:

a) fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC;

b) supply any and all information needed for the evaluation of the products for which certification is sought;

been granted;

c) make claims regarding certification only in respect of the scope for which certification has d) not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized;

e) discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification;

f) use certification only to indicate that products are certified in conformity with specified standards;

g) endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety;

h) comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements;

i) comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers;

j) ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements;

k) provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCBs or the FCCs market surveillance requirements;

l) keep a record of all complaints relating to products compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies;

m) inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until further written notice from the applicant. Sincerely Yours, Daniel J. Schlegel Standards Compliance Supervisor Lutron Electronics Co., Inc.

Date: 2/12/2021 Attn: FCC Office of Engineering and Technology / UL Verification Services TCB Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Subject:

Request for Confidentiality FCC ID:

JPZ0134 To Whom It May Concern:

Schematic Diagram Block Diagram Theory of Operation Antenna Specification Model Differences Letter Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until a period of 180 days after the grant date:

It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. External Photos Internal Photos Test Setup Photos User Manual Best Regards, Daniel J. Schlegel Standards Compliance Supervisor Lutron Electronics Co., Inc.