User Manual For the LTE LTE-B LTE-B-BA LTE-BA GPS Tracker April 15, 2017 Date 2017-04-15 Revision Changes 1.0 Initial version Author Zeev R1.0 The information presented in this document is strictly confidential and contains trade secrets and other confidential information that are the exclusive property of M-Labs Technologies, LLC 2017 M-Labs Technologies LLC 1 / 15 3 2.1 Contents 1 Introduction ...................................................................................................................................... 5 2 Hardware Design ............................................................................................................................. 6 Basic Hardware ...................................................................................................................... 6 GPS .................................................................................................................................................. 7 GPIO ................................................................................................................................................ 7 LEDs ................................................................................................................................................ 7 UART ............................................................................................................................................... 7 USB .................................................................................................................................................. 8 Relay Driver ..................................................................................................................................... 8 Power and Battery .......................................................................................................................... 8 Timers ............................................................................................................................................. 8 Watchdog ........................................................................................................................................ 8 Accelerometer ................................................................................................................................ 8 2.2 Basic RF Performance ................................................................................................................. 8 Certification and Safety ........................................................................................................ 11 2.3 Software Features ......................................................................................................................... 11 3.1 Basic Software ...................................................................................................................... 11 3.2 Remote Update ........................................................................................................................ 11 3.3 Power Modes ........................................................................................................................... 11 3.4 AT Commands ........................................................................................................................... 12 Command Summary ..................................................................................................................... 12 3.5 Acked Mode ............................................................................................................................. 13 3.6 Event Report Format ................................................................................................................. 14 3.7 Reset ......................................................................................................................................... 14 3.7.1 Context Preservation .......................................................................................................... 14 3.8 Startup Banner ......................................................................................................................... 14 Test Method .................................................................................................................................. 15 Hardware .............................................................................................................................. 15 Software Test ........................................................................................................................ 15 Mechanical Structure (mm) .................................................................................................................. 16 FCC Statement ...................................................................................................................................... 17 RF Exposure Warning Statements: ........................................................................................................ 17 IC STATEMENT ....................................................................................................................................... 17 4.1 4.2 4 2017 M-Labs Technologies LLC 4 / 15 1 Introduction g device that combines GPS location with LTE The LTE is a self-contained vehicle trackin CAT1 cellular connectivity. It is primarily a location reporting device that responds to requests
(user, server) and events (timers, geo-fences). Data reports consist of a single record that contains all location data and system status. The device comes pre-configured from the factory. It is ready to use. The LTE appears to a user or a server application as an endpoint device. It can be queried, updated and configured either through a serial connection, an over the air IP connection, or through SMS messaging. The LTE presents itself over these connections as an enhanced cellular modem with attached functional elements. These elements include:
Input/outputs dedicated for ignition, relay, buzzer, and general purpose GPS location engine Accelerometer Serial UART port Timers Watchdog lockup protection Power management Event reporting Voltage monitoring Access to these elements and general purpose interfaces is done through an extended AT command set. Configuration parameters are stored to flash memory and are automatically used on the next power up event. For more details, please reference the AT Command document. Diagram 2017 M-Labs Technologies LLC 5 / 15
(
4G This LTE product is designed based on the Sequans Communications US130Q LTE E-UTRA LTE CAT 1, wireless data/SQN3223) baseband module, which includes an ARM CPU, 4M serial flash, LTE_B2&B4&B12 RF transceiver, and triple-band RF front end circuit. or VZ120Q Antennas for cellular and GPS are internal to the device. 2 Hardware Design 2.1 Basic Hardware Items US130Q LTE E-UTRA Baseband Module Cellular Network Interface Frequency Antenna GPS Antenna UIM requirement Battery Monitor Build in battery manager Interface Dedicate Timers Watchdog Motion Detect LED Battery Working Time Power switch Power Cable color Power Cable connector type Power Consumption 2017 M-Labs Technologies LLC Requirement Based on SQN3223 baseband chipset and SQN3241 RF 4G Transceiver Interrupt Mode Support for LTE B12, B4, B2 B2(MHZ):TX(1850-1910) RX(1930-1990) B4(MHZ): TX(1710-1755) RX(2110-2155) RX(728-746) B12(MHZ): TX(698-716) Internal Dual AntennasMain & Diversity
[B2&B4&B12]
Dedicate high performance ceramic antenna Support2FF SIM No Support: Hot Plug/Unplug Internal analog input Yes Debug UART Application UART USB 12V DC Input1A current, Ground Relay Drive (12V Output ,500mA current) Dedicated Output for buzzer control Ignition Input GPIO Yes External HW via MCU SupportedGPS/G-Sensor 2 LED Supported 1- RED; 1- Green Build in battery80MAH Lion 4 hours No 10 colors 10-pin connector
< 5Watts 6 / 15 The LTE provides support for specialized hardware features through extended AT commands. The features supported include the following:
GPS GPS location functionality is provided by the device GPS receiver. NMEA GPS records can be extracted in real time from the unit via the UART connection using special debug commands that are outside the scope of this document. GPIO One dedicated input, two dedicated outputs, and one general purpose IO are presented to the external environment on the main connector. They are capable of providing system interrupts to generate a report or drive logic levels to external devices. These lines are 2.8V logic level and are 16V tolerant. These pins default to input and are pulled down representing 0 when disconnected. They should be asserted to a known value if used. LEDs Two LED status indicators are provided to verify correct installation and operation. The status LEDs are color coded and directly convey the status of the cellular and GPS subsystems as described in the table below. Their valid operation also indicates operational status and power. LED Red Function GPS Green Cellular Connection Status On: GPS satellites acquired and Locked Flash Slow: GPS satellite search is in progress Off: No power or GPS subsystem fault On: Indicates LTE connection is made Flash Slow: LTE subsystem initialization in progress Flash Fast: LTE initialization but no data connection available Off: No power or LTE subsystem fault The LTE provides user control allowing the LEDs to be extinguished once installation is Tracker from untrained verified. This feature reduces power and further conceals the LTE parties wishing to defeat its operation. UART There are two UARTs provided. A debug UART port is provided for AT commands, data interaction and optionally for application specific control. A second, application UART is provided to be used as an expansion port for sensors and other peripherals 2017 M-Labs Technologies LLC 7 / 15 USB The USB port is provided for provisioning or debug. Relay Driver A 500mA sink capable output pin is provided. This pin is meant to drive a relay coil indented to interrupt the starter solenoid relay for the ignition circuit to a car. Power and Battery The battery monitor is internal analog input scaled such that the DC value of the power input pin to the LTE of the A/D and consequently covers a scale from 0 to 25.5 Volts. system is measured. This value is scaled to span the most significant 8 bits Timers Timers resident on the baseband chip generate periodic interrupts for power down wakeup, watchdog support, periodic report generation and other timer related functions. Watchdog SQN3223 chipset provides internal software Watchdog. The LTE device also includes an MCU that acts as a failsafe external watchdog. The MCU power cycles the system, if no activity is detected for 1 hour. Accelerometer The accelerometer can be used for motion detection and driver behavior monitoring. 2.2 Basic RF Performance Items TRP free space TIS free space Antenna loss Antenna Loss Board RF Specification LTE_B4 RX B4 Frequency range Sensitivity Dynamic range 2017 M-Labs Technologies LLC Remark Requirements B2/B4/B12: >= 20 dBm TRP free space Main: <= -91dBm TIS free space
<= -88dBm Div:
TRP-TX Power Conducted
<= -3dB RX receive sensitivity conducted
<= -3dB TIS 2110-2155MHZ
-99.5dBm (10MHZ_50RB_Downlink)
-23-99.5dBm 8 / 15 LTE_B4 TX 1710MHz1755MHz B4 Frequency range 10Hz Maximum Frequency error 23.38dBm Maximum output power Minimum control output power <-40dBm ACLR OBW IQ OFFSET UTRA2: 46.48 UTRA1: 41.21 UTRA2: 43.87 UTRA1: 40.51 8.87MHZ (10MHZ Nominal)
< -55.6dbc E-UTRA1:39.23 E-UTRA2:38.05 2017 M-Labs Technologies LLC 9 / 15 728MHz ~ 746MHz
-100dBm (10MHZ_50RB_Downlink)
-23 ~ -100dBm
<3%
EVM LTE_B12_RX Frequency range Sensitivity Dynamic range LTE_B12 _TX 699MHz ~ 716MHz Frequency range Maximum Frequency error 10Hz Maximum output power 23.29dBm Minimum control output power <-40dBm ACLR OBW IQ OFFSET EVM LTE_B2 _RX Frequency range Sensitivity Dynamic range LTE_B2 _TX Frequency range 1850-1910MHZ Maximum Frequency error 10Hz Maximum output power 23.28dBm Minimum control output power <-40dBm UTRA2: 45.48 UTRA1: 41.41 UTRA2: 44.87 UTRA1: 41.51 8.87MHZ (10MHZ Nominal)
< -54.7dbc
<3%
E-UTRA1:39.43 E-UTRA2:38.25
(1930-1990)MHZ
-100dBm (10MHZ_50RB_Downlink)
-23 ~ -100dBm ACLR OBW IQ OFFSET EVM UTRA2: 46.48 UTRA1: 41.51 UTRA2: 44.45 UTRA1: 42.51 8.87MHZ (10MHZ Nominal)
< -54.9dbc
<3%
E-UTRA1:39.49 E-UTRA2:38.29 2017 M-Labs Technologies LLC 10 / 15 GPS Frequency Support Sensitivity Tracking Time Requirement L1-band (1.57542GHz) Channels: 210 PRN 66 Search 22 Simultaneous tracking Sensitivity (UHIS):
Tracking: -156dBm Reacquisition: -153dBm Acquisition: -144dBm Acquisition time:
Hot: <2s Warm: <15s Cold: <60s Reacquisition: 2s - 10s Depends on signal level 2.3 Certification and Safety Items Drop Design Temperature Range Humidity:
Altitude:
Vehicle ISO Test FCC Certification Other Certifications ESD Requirement Operator Certifications Requirement 1.2 meter 6 direction standard drop test
-20 to 40C Operation
-50 to +100 C Storage 20% to 90% Operation 10% to 95% Storage
-500 to +18,000m ISO7637-2-2004; ISO7637-3-2007; ISO10605-2008;
ISO16750-2-2010 FCC 47 CFR Part 15 Industry Canada (optional) 10KV non-Conductive Verizon and/or PTCRB / AT&T (optional) 2017 M-Labs Technologies LLC 11 / 15 3 Software Features 3.1 Basic Software Items Network Interface IP Stack Upgrade Method Remote Update Power Modes AT Commands Report Drivers GPIOs LEDs Watch Dog Reset Startup Banner Requirement LTE B2, B4, B12 IPV4/IPV6 Remote update/ PC tool Supported including OMA DM Supported Supported Supported: 3000 records GPIOLEDGPSUART, USB Accelerometer Interrupt for Ignition Status, Buzzer, Relay GPS Status, Network Status Supported Soft reset, hard reset, GPS reset, RF reset Supported supports OTA field upgrades of the resident application. An over the air TFTP 3.2 Remote Update The LTE
(Trivial File Transfer Protocol) connection is made over an IP connection. A replacement file is then transferred from a server to the LTE and that file replaces the previous application image. Additionally the whole stack can be updated using an OMA- DM protocol. 3.3 Power Modes The LTE device supports several power modes that are set by AT commands. In full power mode the GPS is active and the cellular subsystem will maintain a persistent cellular connection whenever service is available. IP connection is maintained according to the configuration of the device. The device can be put in low power mode whenever it runs on a backup battery or if the external battery is low or if it is not moving. In low power mode the GPS is not running and the LEDs are off. The device would return to full power whenever an event occurs that triggers a report. Those events include:
IP change Periodic report GPIO change Battery threshold Heartbeat Watchdog 2017 M-Labs Technologies LLC 11 / 17 Power-up Trip start and stop Ignition Any hardware or software reset will return the device to full power mode. 3.4 AT Commands Extended AT commands are specific to the LTE device. They are closely based on commands that are as similar as possible industry common devices and are essentially subsets of standard LTE also available via the serial and USB interfaces. commands. Native AT commands supported by the SQN3223 modules are Command Summary The following commands are specific to the LTE. The commands listed are intended to be similar to counterparts found in other tracking products by the same vendor. 1. AT+IONAA: Set append mode 2. AT+IONACK: Set acknowledgement mode 3. AT+IONAPN: Set APN 4. AT+IONBIN: Read the factory core software version (read only) 5. AT+IONBZ: Buzzer setting 6. AT+IONCV: Configuration version 7. AT+IONDI: Set distance interval interrupt 8. AT+IONDTE: Set driving time events 9. AT+IONFR: Restore factory defaults 10. AT+IONGF: Set geo fence borders 11. AT+IONGFH: Set geo fence around current location 12. AT+IONGPIO: GPIO Read/Write 13. AT+IONGS: GPS State report 14. AT+IONHB: Heartbeat 15. AT+IONHC: Heading Change 16. AT+IONINFx: List system information segments 17. AT+IONIP: Set target server IP address and port number 18. AT+IONIPC: IP Change report 19. AT+IONIS: Ignition State 20. AT+IONLT: LEDs Timing and Intensity 21. AT+IONLPORT: Set the local IP port number 2017 M-Labs Technologies LLC 12 / 17 22. AT+IONNR: Set time before IP session is closed and restarted 23. AT+IONNW: Set watchdog timeout if no network found 24. AT+IONPM: Set auto power down mode 25. AT+IONRF: Report Format Binary 26. AT+IONRI: Set report timer interval 27. AT+IONRM: Report Mask 28. AT+IONRN: Queue report record for transmission 29. AT+IONRR: Set reset report 30. AT+IONRS: Reset setting - soft/hard, periodic 31. AT+IONSD: Set SMS response destination 32. AT+IONSI: Set interrupt 33. AT+IONSQ: Set queue length 34. AT+IONSR: Set relay driver (GP3) state high or low 35. AT+IONSV: Read the factory application software version (read only) 36. AT+IONTA: Tow Alert 37. AT+IONTID: CDMA tower ID and location data 38. AT+IONUA: Update application firmware OTA 39. AT+IONUC: Update configuration files OTA 40. AT+IONVO: Virtual Odometer 41. AT+IONVTO: Virtual Trip Odometer 3.5 Acked Mode UDP is not a 100% reliable connection and occasional reports or command/responses may be lost. Since all commands have responses, the server can repeat any command to which there is no response. In order to assure reliable reception of reports, LTE devices can be confi either in Normal or Acked mode to send the reports. In the Normal mode the reports are simply sent as is with no acknowledgment from the server. In the Acked mode every report sent is expected to be acknowledged by the server by sending back an ACK message back. If acknowledgement is not received within the specified timeout, the report is re-sent. If the report is not acknowledged after the specified number of attempts, it is queued. If acknowledgement is received after the report is queued (i.e. past timeout of the last attempt), it is ignored. g ured Report is not considered complete until its acknowledgement is received. Thus, if report X is sent and report X+1 is triggered while waiting for acknowledgement of X, report X+1 will be queued until such acknowledgement is received and only then sent. The LTE will attempt to re-send queued report(s) every time a new report is triggered. If there is more than one report 2017 M-Labs Technologies LLC 13 / 17 queued, the reports will attempt to be sent in the order of triggering and only once the report is acknowledged, the next report is attempted. This assures that reports are sent and received in order Acked mode assures that all reports are received, but adds overhead in time and data. Report that is not acknowledged is sent again and eventually will be queued and sent again. The number and frequency of re-tries is configurable via the Report Acknowledgement command. 3.6 Event Report Format Reports are encoded as binary hex. It is also echoed to the debug UART in ASCII format. 3.7 Reset There are a number of resets available on the device. Soft reset only restarts the software running on the device. Hard reset is caused by resetting the whole basband module via a reset pin. There is also an option to reset the GPS and the cellular sub-systems individually. 3.7.1 Context Preservation When a self-initiated reset is performed due to Network Watchdog or by the Reset command
(modes 0, 1), the context of the system is being preserved and is restored after the reset. The context includes all the periodic timers, the report queue, the odometer, etc. This allows reset of the unit as a troubleshooting or preventive measure without losing reports that are already in the queue or are pending on running timers. Note that the reset process may cause 1-2min of inaccuracy in the timers and should not be considered as very precise. 3.8 Startup Banner After a reset a startup banner is printed through the UART only. 2017 M-Labs Technologies LLC 14 / 17 4 Test Method 4.1 Hardware Test Item Baseband Function Test RF Test Description Power Input Test Power Consumption and Current Test Heat Dissipation Test UART Stability Test GPIO Level Test LED Stability Test Drop Down Test ESD Test High/Low Temperature Test Humidity Test RF Performance Test GPS Performance Test Antenna Performance Test 4.2 Software Test Test Environment Construct Message Test environment 1. USB dongle and PC as message server 2. Send message to LTE UDP Test environment 1. Connect dongle to PC and create dialup as ip server 2. LTE create IP connection to server UART Test environment 1. Connect LTE to PC with com serial cable 2. Open Terminal tool and send at command 3. Response can be shown at terminal window 2017 M-Labs Technologies LLC 15 / 17 Mechanical Structure (mm) 2017 M-Labs Technologies LLC 16 / 17 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter ISEDC Warning :
This device complies with Innovation, Science, and Economic Development Canadalicence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference,
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d' Innovation, Sciences et Dveloppement conomique Canada(Industrie Canada) applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Cet uipement est conforme aux limites d'exposition de la radiation dermins pour un environnement non contr? Cet uipement devrait re install?et re actionn?avec la distance minimum 20cm entre le radiator& votre corps.Cet etteur ne doit pas re Co-plac?ou ne fonctionnant en me temps qu'aucune autre antenne ou etteur. 2017 M-Labs Technologies LLC 17 / 17