am 46-1 Quick Start www.magorcorp.com How to connect the display wall:
Introduction PC
(Out) IN OUT RS-485 (IN) RS-485 (OUT) RS-485 (IN) RS-485 (OUT) RS-232 TO RS-485 RS-485 Cable RS-485 Cable Back Interface Sketch Map REMOTE RS485 IN RS485 OUT HDMI IN SERV-C REMOTE Infrared remote input SERV-C For service use(do not insert the IR Receive here) Remote Control Line 4 123 3.5 Note:1.VCC 2.IR-INPUT 3.LED 4.GND 2 M 1 How to load the supplied batteries into the remote control:
1. Remove the battery compartment lid on the back of the remote control. 2. Insert two AAA-sized batteries into the battery compartment, making sure the positive + and the negative - polarity line up correctly as indicated in the case. 3. Close the battery compartment lid. Introduction 2 3 Description of remote control buttons:
(standby) To turn the display on or off (standby). PICTURE To select one of the four preset picture settings
(STANDARD, BRIGHT, SOFT and PERSONAL) ASPECT To select the aspect ratio (4:3 and FULL). PRO. VOL. OK MENU EXIT INFO PROGRAM UP/DOWN To vertically scroll in menus, select menu options in menu controls. VOLUME UP/DOWN To change values in menus. To confirm a selection or enter submenu. To access the overview menu. To return to the previous menu. To close a menu or remove any display. To display status information of signal. NOTE:
The display has the feature of auto off without signal for 15minutes. AML 2 Menu Operation PICTURE B R I G H T N E S S C O N T R A S T C O L O R T E M P . S C A L E M O D E P I C T U R E M O D E B A C K L I G H T D E F A U L T M O N I T O R _ I D 5 0 4 0 5 0 N O R M A L F U L L S O F T O F F 4 OK SELECT EXIT MENU Follow the steps below to set the menu:
1. Press the MENU button on the remote control to display the onscreen menu. 2. Press the VOL. or OK button on the remote control to enter the PICTURE menu. 3. Press the PRO. or button on the remote control to scroll through the picture features and use VOL. or to adjust:
BRIGHTNESS: to adjust until the darkest parts of the picture become as bright as you want. 50 is the default status. CONTRAST: to increase or decrease the difference between the black portions and white portions of the picture. When contrast is increased, it helps sharpen the picture. 50 is the default status. COLOR TEMP.: to select NORMAL, WARM or COOL picture preferences. For NORMAL, whites will maintain their whiteness; COOL will make the whites bluish; and WARM will make the whites reddish. NORMAL is the default status. SCALE MODE: to select FULL or 4:3 aspect ratio. PICTURE MODE: to select a picture mode among STANDARD, BRIGHT, SOFT and PERSONAL. BACKLIGHT: to adjust the background light. DEFAULT: to make the three options of BRIGHTNESS, CONTRAST and COLOR TEMP. back to the default value. MONITOR_ID: to set an ID number for a certain display unit. 3 PC Operation Follow the steps below to operate on the display wall with a PC. The user interface appears as right. 1. Power On/off:turn on/off the display wall. 2. The display wall may consist of a maximum of 25 display units . Every unit should have its ID No.. If you click on Select ID, you can go on to select a certain ID No.;
If you select All, the operation will work on all the connected display units on the whole wall. If you select a certain ID No., the operation will work on the certain display unit. If you click on Set ID, there appears automatically a SET button on the right and you can go on to set an ID No. to the connected display unit by selecting a certain No. and then pressing the SET button to confirm. Note: the All function is not available. 3. Inside the COM frame, you can select a PC terminal to connect the display wall. Note: when a certain terminal is occupied, you cant use it. Only when it is released, you can use it by re-clicking on the the terminal. 4. Click on the MENU button to display the overview menu on the unit. 5. In the Adjusting frame, you can do the following operations:
Click to select a picture mode: standard, Soft, Bright or Personal;
Click and hold the mouse to move left or right to adjust the brightness of the picture. Click and hold the mouse to move left or right to adjust the contrast of the picture. Click and hold the mouse to move left or right to adjust the background light. Click to select a color temperature: Normal, Warm or Cool. If you want to restore all adjustments to the default status, just click on the Default button. 6. If there is any information feedback from the display units, it will appear in the display Info frame. Note: this function is not available. If there is information in the Display Infowindow ,press Clr ,it will be cleared. 7. While you are working on the PC, every time you move the mouse to a certain position like B.Light, there is some help information displayed in the Help Info frame. 4 Other Information NOTE 1:This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. NOTE 2:Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Bracket installation MESH AREA IS FOR BACK SUPPORT 5 Specification Main unit:
Working voltage: 110-240V~ 50/ 60Hz Ampere: 2.54A Power consumption: <2W (in standby mode) Screen size (diagonal): 116.8cm Dimensions (WXDXH): 1059mm X128mm X 612mm Environment:
Working temperature: 5 C~35 C Working humidity: 20%~80%
Storage temperature: -15 C~45 C Storage humidity: 10%~90%
Display mode: On-screen display OSD language: English Interface HDMI input:1920 1080P/60Hz Ver1.2 RS 485 in RS 485 out Remote in Character:
WEIGHT: NET: 25 Kg Brightness: 500 cd/m 2 Contrast ratio: 1800:1 Viewing angle : 178 Response time. G to G: 8ms Scanning frequency: 50/60 Hz Native resolution: 1920 1080p 6