Advanced Smart Cruise Control System 1 I. System Information 1. Introduction The ASCC system operates the convenience feature automatically maintaining the distance by measuring the distance and speed of the lead vehicle with the radar in front of the car. Also, if the lead vehicle is stopped along the rear of the lead vehicle stops, and re-start feature provides at the start with Stop & Go function. 2. System Operation operation principle Absence of a lead vehicle Existing of a lead vehicle Stopping a lead vehicle Blinding a lead vehicle Cluster display state Cruise control at the drivers setting speed Driving the lead vehicle traveling speed maintaining a set following distance When auto stop and starting the lead vehicle within 3 seconds, automatically start. Accelerate to the target speed and then cruise control. 1) Normal Mode Control All of the speed/distance control can perform from 30 to 180 km/h speed range. The minimum target speed is 30km/h. If the lead vehicles speed is from 0 to 30km/h, the proper distance can be expected(or calculated/measured). 2) Stop mode Control When the lead vehicle is stopped, and then the vehicle would stop at a certain distance. If the stop duration is within 3 second, the vehicle automatically start, or not manually the resume/set switch turn on or the accelerator pedal is pressed. If the stopping maintain more than 5 minutes, the ASCC control will be released. 3) Overdrive Control Driver's accelerator pedal is pressed, the system will give acceleration priority to the judgment of the driver than the system decision. Then, the driver releasing the accelerator pedal, the target speed gradually slows down. 4) Overtaking Support Control The driver turn on the left blinker, the system internally set as the target distance one-step regardless of the display condition. Therefore, a slight acceleration can help to occur soft overtaking. 2 II. Specific System Structure 1. SCC 1) Function Monitoring front road condition(sensing function) Driver riding/getting off and monitoring car condition(ECU function) Calculating and output of the Required acceleration(ECU function) 2. Switch 1) Function ACSS system On/Off Target speed control Target distance control Operation ON/OFF ASCC-CC switching operation 3. Cluster 1) Function System On/Off System Alarm ASCC Operation State (lead vehicle, Break, Overtake, Stop modes) Display ASCC Driver Setting State (Target Speed/Distance) Display ASCC Auto-unlock/ Usage Condition Un-satisfaction ASCC Hazardous situation (lead vehicle breaking, Stop vehicle alert) Display 3 4. Instruction of the ASCC control using switch 1) ON/OFF Main Switch ON/OFF function In case of the Standby mode, CRUISE Ramp turn ON 2) SET/ Switch At the Stand by mode, Press SET Switch and then Control start. The target speed set 30 km/h when the car speed is from 0 to 30 km/h. When the car speed is over 30 km/h, the target speed is the same as current speed. If the SET switch is pressed under control, the target speed will be decreased. Press short period, the speed decrease 1km/h step. ex) 81807978 Press long period, the speed decrease at first 1km/h step then 10km/h step. ex) 77767060 3) RES/+ Switch At Standby mode, Press RES+ switch and then control start. After the OFF mode changed to Standby mode, the ASCC usage history have to be existed at least once. If the RES+ switch is pressed under control, the target speed will be increased. Press short period, the speed increase 1km/h step. ex) 7778798081 Press long period, the speed increase at first 1km/h step then 10km/h step. ex) 66677080 4) CANCEL Switch Released from the control condition 5) Distance setting switch Set the target headway distance(Initial value is level.4) Press the switch, the target headway distance value changed in the following order. level.4->level.3->level.2->level.1->level.4 In case of the car speed is 90km/h At level 1 (1sec.), Headway distance is 25m. At level 2 (1.3sec.), Headway distance is 32.5m At level 3 (1.6sec.), Headway distance is 40m At level 4 (2.1sec.), Headway distance is 52.5m If press the switch over 2 sec, the ASCC mode is switched the CC mode each other. 4 Notice:
This Device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)]. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) This device must accept any interference received, including interference that may cause undesired operation. Notice:
Changes or modifications made to this equipment not expressly approved by (manufacturer name) may void the FCC authorization to operate this equipment. 5 ForFCC ThisdevicecomplieswiththeFCCRules.Operationissubjecttothefollowing twoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevice mustacceptanyinterferencereceived,includinginterferencethatmay cause undesiredoperation. Anychangesormodificationsnotexpresslyapprovedbythepartyresponsible forcompliancecouldvoidtheauthorityto operateequipment. Thisdeviceanditsantennamustnotbecolocatedoroperatinginconjunction withanyotherantennaortransmitter. Endusersandinstallersmustbeprovidedwithantennainstallationinstructions andtransmitteroperatingconditionsforsatisfyingRFexposurecompliance. FCC RF Radiation Exposure Statement:
ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforan uncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwith minimumdistance80cmbetweentheradiator&yourbody. For IC This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1)This device may not cause interference;
and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body Dclaration d'exposition aux radiations:Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20 cm entre le radiateur et votre corps. Equipment Operating Information
- Minimum Operating Temperature : -40
- Maximum Operating Temperature : +85
"Hereby, MANDO Corp. declares that the radio equipment type Automotive Radar/MRR-20 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the internet address:
https://www.mando.com/ )"
Equipment RF Specification Product name Kind of product LRR-25 Automotive Radar Operating frequency range 76.125 GHz ~ 76.95 GHz Bandwidth Type(s) of Modulation
(e.g. BPSK, FSK, ASK, ) 825 MHz FMCW Number / Type of Antenna(s) 10(Tx :2 EA, Rx: 8 EA) / patch ANT Antenna Gain Tx1: 21 dBi, Tx2: 14 dBi, LRx: 18 dBi, SRx: 14 dBi Intended area of use Automobile Test sample information production unit Wired Interfaces Power supply:
Voltages CAN/LIN Cable Length: 2 m Battery Vnom Vmax Vmin
: 12 V
: 16 V
: 9 V Current consumption 500 ~ 600 mA Dimensions (in cm):
101.5 x 77 x 21.5 Weight:
240 g 3