Maranteciivg Transmitters ML-1401V, -1402V, -1404V, -1431V, -1432V, -1434V Instructions for MAC Lift Models: ML-2401V, -2402V, -2404V, -2431V, -2432V, -2434V, -3431 FEATURES Figure 1. Battery Compartments Marantecs family of state-of-the-art transmitters is -
. : . A. Midi tailored for discerning homeowners. Each transmitter transmitter Battery nent is custom encoded and ergonomically designed SS Cover to be an integral part of your garage door opener Programming 12V (type 23) system. Marantec offers 3 styles to suit your personal preference: the Midi (1-, 2- or 4-channel), the Mini 3-hole Terminal
(1-, 2- or 4-channel), and the Micro (1-channel), the smallest transmitter of its kind. B. Mini
. Transmitter 1. Installing the Battery <> :
"_ Battery Midi (Figure 1. A) and Mini (Figure 1. B) SS compartment
@ Remove battery compartment cover (back of transmitter) 12V (type 23A) by using small screwdriver or coin. Battery M@ Insert the provided 12V battery (type 23A) as shown. q Ss hole Terminal M Replace battery compartment cover. SEZ Micro (Figure 1. C) Micro transmitters come with batteries already installed. When ergramming BY (type CR1025) replacing batteries follow the steps below: SZ Programming
. Se Cable mM Remove battery compartment cover (front of transmitter). C. Micro Insert two 3V batteries (type CR1025) as shown. Transmitter
@ Replace battery compartment cover. Note: Replace batteries with same type only. ~ 4s 2. Using the Transmitter Terminal <_ Compartment Cover M To open or close garage door, press and hold button (Midi and Mini transmitters have indicator lights that will start blinking). When garage door begins to move, release button. To stop garage door during travel, press and hold button until door stops, then release button.
@ To continue garage door travel after stopping it, press A. Midi or Mini Transmitter and hold button. Figure 2. Mounting Plates 3. Transmitter Mounting The transmitters can be conveniently mounted inside your car using the mounting plate, or the mounting plate and visor clip (Midi and Mini Transmitters only). Mounting Plate (Figure 2.) The mounting plate enables you to mount the transmitter easily to the dash or other convenient area.
@ Secure the mounting plate to area of preference using velcro (not provided) or other means. Snap the transmitter into the mounting plate, which will hold it firmly in place. Micro Transmitter Micro Mounting Plate Transmitters Instructions (continued) 3. Transmitter Mounting (continued) Figure 3. Visor Clip and Mounting Plate, Visor Clip (Midi and Mini Transmitters: Figure 3.) Midi and Mini Transmitters The visor clip permits easy mounting of the transmitter to a visor.
@ Attach visor clip to mounting plate. M@ Snap transmitter into mounting plate. Affix complete assembly to visor. 4. Multiple Transmitters Each transmitter comes factory programmed with random codes. 1-channel transmitters have one random code, 2-channel transmitters have 2 different random codes, one per button, and 4-channel transmitters have 4 different random codes, one per button. Transmitters that accompany a power head have at least one code that already matches that power head. Transmitters that are purchased separately as accessories have random codes that must be changed in order to match the code of the active transmitter you are already using. Below are instructions for trans-
ferring an active code from a button on one transmitter Visor Clip to a button of your choice on another transmitter.
@ Remove battery compartment covers (as shown previously in Figure 1) of both transmitters, the one with the active code and the new transmitter that needs to receive the active code.
@ Connect programming cable to both transmitters. Line up either end of stripped cable so 3 wires align with terminals, then firmly insert cable. See Figure 4.
@ Press and hold button on transmitter with the active code
((L) in Figure 4). Midi and Mini transmitters have indicator lights that will blink to show that code transfer is ready. While keeping the transmitter (L) button pressed, press and hold the button on the new transmitter (R) that you want to transfer the active code to. Figure 4. Multiple TransmittersCode
@ Code transfer will occur in approximately 2 seconds. If the Transfer new transmitter (R) is a Midi or a Mini, the indicator light will illuminate continuously to show that transfer is complete. All buttons can be released. Code transfer is completed. Transmitter with Active Mi Cable can be removed and the covers replaced. Code
@ Both transmitters can now be used to operate the same door. New Transmitter Note: For multi-button transmitters, be sure to carry out this procedure for all the buttons you desire to use. Light Illuminates Continuously Press First Press Second Keep Pressed Release when Light illuminates Continuously FCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 8030012 1998 Ali rights reserved. 0600