2D Wireless Barcode Scanner Quick Guide FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following and on, the user measures:
measures:
Reorient or relocate the receiving antenna. Reorient or rel Increase the separation between the equipment and receiver. Increase the se Connect the equipment into an outlet on a circuit different from that to which the Connect the e receiver is connected. receiver is co Consult the dealer or an experienced radio/TV technician for help. Consult the de CANADIAN DOC STATEMENT CANADIAN DOC This digital appa This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set ou apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Communications. r Le prsent appa Le prsent appareil numrique nmet pas de bruits radiolectriques dpassant les limites applicable limites applicables aux appareils numriques de las classe B prescrites dans le RR Rglement sur le Rglement sur le brouillage radiolectrique dict par les ministre des Communica-
tions du Canada tions du Canada. CE MARKING AN CE MARKING AND EUROPEAN UNION COMPLIANCE Testing for compliance to CE requirements was performed by an independent Testing for comp laboratory. The unit under test was found compliant with all the applicable Directives, laboratory. The u 2004/108/EC a 2004/108/EC and 2006/95/EC. WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WASTE ELECTRI The WEEE directive places an obligation on all EU-based manufacturers and The WEEE direct importers to take importers to take-back electronic products at the end of their useful life. AA ROHS STATEME ROHS STATEMENT OF COMPLIANCE This product is compliant to Directive 2002/95/EC. This product is co NON-MODIFICA NON-MODIFICATION STATEMENT Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment rr RoHS WARNING AND CAUTION 1. Take any metals into contact with the terminals in connectors. 2. Use the scanner where any inflammable gases. If following condition occur, immediately power off the host computer, disconnect the interface cable, and contact your nearest dealer. 1. Smoke, abnormal odors or noises come from the scanner. 2. Drop the scanner so as to affect the operation or damage its housing. Do not do behavior below. 1. Put the scanner in places excessively high temperatures such as expose under direct sunlight. 2. Use the scanner in extremely humid area or drastic temperature 3. Place the scanner in oily smoke or steam environment such as cooking changes. range. 4. Be covered or wrapped up the scanner in bad-ventilated area such as under cloth or blanket. 5. Insert or drop foreign materials or water into scanning window or vents. 6. Using the scanner while hand is wet or damp. 7. Use the scanner with anti-slip gloves containing plasticizer and chemicals or organic solvents such as benzene, thinner, insecticide etc to clean the housing. Otherwise, it could not result fire and electrical shock but housing may be broken and injured. 8. Scratch or modify the scanner and bend, twist, pull or heat its interface cable. 9. Put heavy objects on interface cable. Do not stare the light source from the scanning window or do not point the scanning window at other peoples eyes or eyesight may be damaged by direct exposure under the light. Do not put the scanner on an unstable or inclined plane. The scanner may drop, creating injuries. Once the interface cable is damaged such as exposed or broken copper wires, stop using immediately and contact your dealer. Otherwise, it could result fire or electrical shock. Do Not BEEPER INDICATION Single short beep Single long beep Two beeps Two beeps (high-low) Two beeps (low-high) Three short beeps Three beeps
(low-medium-high) One short beep & one long beep (low-high) One short beep & one long beep (high-low) Seven beeps
(shuts down thereafter) LED INDICATION Flashing blue & green Flashing blue Solid blue 1 green flash 2 green flashes Solid red i. Wireless connection ii. Good read Power down Wireless disconnection Succesful configuration Good read (Memory Mode) Reads a barcode while disconnected Succesful configuration Power up Power off Low power (Battery life < 5%) Discoverable in BT HID Discoverable in BT SPP Connected Good read / Power up Disconnected Charging 2D Wireless Scanner Quick Guide (Rev1) P/N: 8013-0078000 GETTING CONNECTED (CRADLE MODE, USB) GETTING CONNECTED (CRADLE MODE, RS232) GETTING CONNECTED (BT HID) GETTING CONNECTED (BT SPP) The following steps apply to the scanner paired with a charging cradle whose bottom label is printed with USB HID:
The following steps apply to the scanner paired with a charging cradle whose bottom label is printed with RS232:
BT HID is compatible with iOS, Android and Windows and requires applications that accept keyboard data. Folllow below steps:
BT SPP is compatible with Android and Windows. A serial communi-
cation software is required for this profile. Follow below steps:
1. Plug the charging cradle to host device with an USB cable. 2. Power up the scanner by pressing the trigger. 3. Scan USB HID Cradle Mode (recommended) or USB VCP Cradle Mode. 1. Plug the charging cradle to host device with an RS232 cable. 2. Power up the scanner by pressing the trigger. 3. Scan RS232 Cradle Mode. 1. Power up the scanner by pressing the trigger. 2. Scan BT HID. 1. Power up the scanner by pressing the trigger. 2. Scan BT SPP, the scanner will emit two beeps with LED indicator flashing blue. USB HID Cradle Mode USB VCP Cradle Mode 4. The scanner will emit one short beep with LED indicator turning solid blue after successfully connecting to charging cradle. If the charging cradle fails to connect to the scanner, scan Disconnect, as seen in step 3 of Getting Connected (BT HID), unplug the cable from charging cradle and plug it back. The charging cradle will be able to connect to the nearest scanner when the cable is plugged. 5. To swap charging cradle, please follow step 1 ~ 3, and then scan Disconnect, as seen in step 3 of Getting Connected (BT HID), unplug the cable from the charging cradle you want to disconnect, and plug the cable to the charging cradle you want to connect. The charging cradle will be able to connect to the nearest scanner when the cable is plugged. RS232 Cradle Mode 4. The scanner will emit one short beep with LED indicator turning solid blue after successfully connecting to charging cradle. If the charging cradle fails to connect to the scanner, scan Disconnect, as seen in step 3 of Getting Connected (BT HID), unplug the cable from charging cradle and plug it back. The charging cradle will be able to connect to the nearest scanner when the cable is plugged. 5. To swap charging cradle, please follow step 1 ~ 3, and then scan Disconnect, as seen in step 3 of Getting Connected (BT HID), unplug the cable from the charging cradle you want to disconnect, and plug the cable to the charging cradle you want to connect. The charging cradle will be able to connect to the nearest scanner when the cable is plugged. BT HID 3. Press and hold the trigger until beeps with LED indicator flashing blue and green. Alternatively you may scan Disconnect. BT SPP 3. Pair with BarCode Scanner spp from the discovered device list. If the host is unable to find the scanner in the discovered device list, scan Disconnect. Disconnect 4. Pair with BarCode Scanner HID from the discovered device list. 5. The scanner will emit one short beep with LED indicator turning solid blue after successfully connecting to the host device. Disconnect 4. Enter serial communication software (TeraTerm, PuTTY, etc) and open the serial port occupied by the scanner. 5. The scanner will emit one short beep with LED indicator turning solid blue after successfully connecting to host device. DEFAULT CHECK VERSION BATTERY LIFE GENERAL SETTINGS SLEEP TIMEOUT BUZZER UPPER / LOWER CASE 30 SECONDS 1 MINUTE LOW VOLUME MEDIUM VOLUME ALL LOWER CASE ALL UPPER CASE 5 MINUTES 30 MINUTES HIGH VOLUME INVERT CASE AS IS VIBRATOR iOS TOUCH KEYBOARD NEVER
(Scanner Always On) IMMEDIATE
(Scanner Shuts Down) ON OFF TOGGLE iOS KEYBOARD
*Note: Alternatively, simply double-click the trigger. TERMINATOR MEMORY MODE KEYBOARD LAYOUT CR LF ENTER MEMORY MODE EXIT MEMORY MODE ENGLISH (US) ENGLISH (UK) ITALIAN JAPANESE TAB NONE UPLOAD MEMORY DATA CHECK MEMORY DATA COUNT GERMAN PORTUGUESE DUTCH GERMAN
(iOS KEYBOARD) CR + LF ERASE MEMORY DATA FRENCH SPANISH SWISS (GERMAN) SWISS (FRENCH) FCCWarningStatement Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecould voidtheusersauthoritytooperatetheequipment.Thisequipmenthasbeentestedandfoundto comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidential installation. This equipment generates uses and can radiate radio frequency energy and, if not installedandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradio communications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticular installation. If this equipment does cause harmful interference to radio or television reception, whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotryto correcttheinterferencebyoneormoreofthefollowingmeasures:
Reorientorrelocatethereceivingantenna. Increasetheseparationbetweentheequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris connected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp. Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowing twoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and
(2) this device must accept any interference received, including interference that may cause undesiredoperation. The device has been evaluated to meet general RF exposure requirement.