USERS MANUAL WIRELESS MICROPHONE SYSTEM TALK INTRODUCTION WIRELESS Introduction Thank you for purchasing our product. This PLL synthesized wireless microphone system operates in UHF band frequency with 700 selectable channels. Please read this instruction manual carefully before operating the system. This manual covers the function and operation of the wireless microphone system. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-located or operating in conjunction with any other antenna or transmitter. Safety Do not spill liquid on the appliance and do not drop it on a hard concrete floor. Do not place the equipment near heat sources such as radiators, heating ducts, amplifier, etc. Do not expose the equipment to direct sunlight, extremely dust, excessive moisture, rain, mechanical vibrations, or shock. Take out the battery from transmitter, if the appliance has been not used for a longer period. This will avoid the damage resulting from a defective leaking battery. If the equipment is not going to be used for a long time, disconnect the AC adapter from the power outlet. Please note that if you turn the equipment off while leaving the AC adapter plugged in, it is not fully isolated from the power supply. WARNING: To reduce the risk of fire or electric shock, do not use the products near water and do not expose them to rain or moisture. No guarantee claims for the equipment and no liability for any resulting personal damage or material damage will be accepted if the equipment are used for other purpose than originally intended, if the equipment are not correctly connected or operated, or if the equipment are not repaired in an expert way. Environment Do not throw used batteries into a fire or garbage bin with domestic rubbish. Be sure to dispose of used batteries in accordance with local waste disposal rules. When disposing the equipment, remove the batteries, separate the case, circuit boards, and cables, and dispose of all components in accordance with local waste disposal rules. 1 Quick Start Guide 1. Connected Receiver Power Cable AUDIO OUT UNBALANCED LINE MIC SQ DC ONLY 12V 500mA BALANCED C D C A
/
R E T P A D A 2. Connect Mixer or Amplifier ANT B AUDIO OUT UNBALANCED LINE MIC DC ONLY 12V 500mA SQ ANT B ANT A AUDIO OUT UNBALANCED LINE MIC DC ONLY 12V 500mA SQ ANT A BALANCED BALANCED 3. Scan Free Channel VOLUME 10 9 8 12 11 1 52 6 7 2 4 3 VOLUME 2 4. Insert Batteries 5. SYNC P o w e r S y n c
-10 0
- 2 0 1.5V AA 1.5V AA 10 9 8 12 11 7 6 1 5 2 4 3 P o w e r S y n c
-10 0
- 2 0 1.5V AA 1.5V AA 1.5V AA 10 9 8 1.5V AA 2 1 3 12 11 4 7 5 6
< 1M Step 2 Hold S y n c P o w e r S y n c 10 0
- 2 0 1.5V AA 1.5V AA OR T A L K Hold T A L K Step 1 3 WIRELESS Receiver Front :
PRODUCT DESCRIPTION 1 2 3 4 5 6 1. Power Button. 2. LCD Display: Display channel, frequency and settings. 3. Button : Tap the channel forward / backward. 4. SYNC Button: Press the button to actuate the synchronization with transmitter. 5. SET Button: Press button to active the manual or auto-scan or preset mode. 6. Volume Controller: Adjust the receiver output level. LCD Display :
5 6 1 3 2 4 7 8 9 10 11 1. Manual: Use this mode to select free channel by manually. 2. Scan: Use this mode to set free channel by auto-scan function. 3. Preset: Use this mode to set multiple constructions by preset group. 4. SYNC: The synchronization process is actuated. 5. GP: Display selected preset group. 6. CH: Display selected preset channel. 7. CH: Display selected channel number. 8. FREQ.: Display selected frequency. 9. MUTE: Audio output is muted. 10. RF Bar: Display the reception status of RF signal. 11. AF Bar: Display the reception status of AF signal. 4 PRODUCT DESCRIPTION WIRELESS Rear :
ANT B AUDIO OUT UNBALANCED LINE MIC DC ONLY 12V 500mA SQ ANT A BALANCED 1 2 3 4 5 6 1 1. Antenna 2. Balanced XLR Audio Output 3. Unbalanced 6.35mm Audio Output 4. Mic/Line Switch: Use this to adjust audio output level for mic level (-20dB) or line level (0dB). 5. Squelch: Turn the knob to adjust or decrease the noise floor level. 6. Power Adapter connector 5 WIRELESS PRODUCT DESCRIPTION Handheld Microphone 7 5 K L A T 4 3 1.5V AA 1.5V AA 6 1 2 1. Power Button: Press for 2 seconds to power the microphone on or off. 2. Power LED: Indicate the power / low battery level status. LED Indicator Green Status Ready Flashing Green The synchronization process is actuated. Flashing Red Low battery power when less than 10 minutes operation 3. Talk Button: Push the button up to talk. Push the button down for mute. 4. SYNC Button: Press to actuate the synchronization process with the receiver. 5. LCD Display: Display channel number and battery power level. 6. Battery component: Insert two AA dry or rechargeable batteries into the compartment and make sure that the polarity of batteries is correct. 7. Grille: Protects the microphone capsule and helps reduce breath sounds and wind noise. 6 PRODUCT DESCRIPTION WIRELESS Bodypack Transmitter 4 2 3 1 5 P o w e r S y n c
-10 0
- 2 0 1.5V AA 1.5V AA 8 6 9 7 1. Power Button: Press for 2 seconds to power the microphone on or off. 2. Mute Button: With the transmitter on, a slight press for button will toggle between mute and unmute function. 3. Power LED: Indicate the power / low battery level status LED Indicator Green Status Ready Flashing Green The synchronization process is actuated. Flashing Red Low battery power when less than 10 minutes operation 4. MUTE LED: Blue LED light on in mute status. 5. SYNC Button: Press to actuate the synchronization process with the receiver. 6. LCD Display: Display channel number and battery power level. 7. Battery component: Insert two AA dry or rechargeable batteries into the compartment and make sure that the polarity of batteries is correct. 8. Mini XLR Connector: Connect to the lapel microphone or headset microphone. 9. Gain Switch: The switch sets the audio input to -20dB, -10dB, 0dB. 7 WIRELESS SYSTEM OPERATION Connecting the receiver Prior to setting up, please check that the transmitter and receiver are tuned to the same frequency or channel. Two or more transmitters operating in the same frequency can not be used at the same time and area. 1 2 AUDIO OUT UNBALANCED LINE MIC SQ DC ONLY 12V 500mA BALANCED C D C A
/
R E T P A D A ANT B AUDIO OUT UNBALANCED LINE MIC DC ONLY 12V 500mA SQ ANT A BALANCED ANT B AUDIO OUT UNBALANCED LINE MIC DC ONLY 12V 500mA SQ ANT A BALANCED AUDIO OUT 3 UNBALANCED LINE MIC DC ONLY 12V 500mA SQ BALANCED 4 VOLUME AUDIO OUT 5 UNBALANCED LINE MIC DC ONLY 12V 500mA SQ BALANCED Connected the provided DC power supply to the receiver power input with an appropriate AC power source. The LCD display will light and the receiver is on. Using a standard audio cable with 3-pin XLR connectors or 6.3mm phone plugs to connect the mixer or amplifier. Never use the balanced and unbalanced audio outputs at the same time! This may cause signal loss or increased noise. ANT A Set the audio output level for MIC: -20dB LINE: 0dB (Default Setting) Using the Volume Controller to adjust the AF audio level to the input of the amplifier or mixer. Default Setting: In minimum VOLUME position. Use squelch to eliminate or suppress the ambient RF noise. Defaulting Setting: In properly position. min. SQ VOLUME max. SQ VOLUME TALK TALK 8 SYSTEM OPERATION WIRELESS Setting up channel on receiver Manual Mode Setting interference-free channel by manual operation. Using the mode. button to select the MANUAL Press SET button for 2 seconds till LCD display is flashing. Press button to change the channel forward. Press the SET button to lock the setting. 9 WIRELESS Auto-Scan Mode SYSTEM OPERATION Set interference-free channel by automatic frequency scan function. Using the button to select the SCAN mode. Press SET button for 2 seconds till LCD display is flashing. to scan in forward direction, and Press button it will stop at the free-interference channel automatically. Press the SET button to lock the setting. 10 SYSTEM OPERATION WIRELESS Preset Mode Set multiple constructions by using preset channels. There are 4 preset groups. Excluding the interference from external, there are 8 preprogrammed channels can be operated simultaneously in each group. Using the button to select the PRESET mode. Press SET button for 2 seconds till LCD display is flashing. Press channel button to change the programmable group forward. Press the SET button to lock the group setting. Press channel button to change the programmable channel forward. Press the set button to lock the channel setting. NOTE:When there is any outside interference on the current preset group, please switch to use next preset group. If 4 preset groups are all under interference, please use auto-scan mode or manual mode to set up system. 11 WIRELESS SYSTEM OPERATION Set up the handheld microphone / bodypack transmitter Open the battery cover and insert batteries into the battery compartment conforming to the polarity (+)(-) marks. P o w e r S y n c
-10 0
- 2 0 1.5V AA 1.5V AA Unscrew the handheld Mic and open the battery cover to insert the battery into the battery compartment and confirm the marks of the polarity (+) (-). Connect to the lavalier microphone, headset microphone or guitar cable. 12 SYSTEM OPERATION WIRELESS 1.5V AA 12 11 10 9 8 7 6 1.5V AA P o w e r 1 5 2 4 3 S y n c 10 9 8 12 11 7 6 1 5 2 4 3
-10 0
- 2 0 1.5V AA Bodypack Handheld 1.5V AA P o w e r S y n c
-10 0
- 2 0 P o w e r S y n c
-10 0
- 2 0 1.5V AA 1.5V AA 1.5V AA 1.5V AA Press for 4 seconds to turn the Handheld/
Bodypack transmitter on. If the LED stays flashing , it indicates that the battery will out of power soon and should be changed. Adjust the audio input level.
0dB (Default Setting)
-10dB
-20dB
0dB
-10dB
-20dB NOTE: When you dont use this device for a long term period, please switch the power switch to off mode to save more electric power. 13 WIRELESS SYSTEM OPERATION Synchronizing a transmitter with a receiver Automatic frequency synchronization via remote channel for easy setup. First, switch the transmitter and the receiver on. Press and hold the SYNC button on your transmitter. The SYNC flashes on the receiver display panel. Press the SYNC button on the receiver front panel, the transmitter will set the same channel as receiver automatically. When using SYNC setting, the distance of receiver and transmitter is within 1 M.
< 1M Step 2 Hold S y n c P o w e r S y n c 10 0
- 2 0 1.5V AA 1.5V AA OR T A L K Hold T A L K Step 1 14 COLOR LABEL IDENTIFICATION WIRELESS Color Label Identification You can also stick the color label on the receiver and transmitter for quickly identify the pair system. TALK 15 WIRELESS BASIC CONNECTIONS Basic Connections To combine two receivers in a 19 standard rack by using 2 short L type metal racks and 2 metal connecting plates. L4 To mount a receiver in a 19 standard rack by using 2 long L type metal racks.
(L type long metal racks is an optional product, so please purchase extra in local shops.) L3 By using the antenna holder to install the UHF antenna in high place for better reception quality. Antenna Antenna AUDIO OUT UNBALANCED LINE MIC SQ DC ONLY 12V 500mA BALANCED Antenna Holder Antenna Holder 16 TROUBLE SHOOTING WIRELESS Trouble Shooting whether is set too high or too low. 17 WIRELESS SPECIFICATION System Performance Receiver Frequency Range Case Oscillator Modulation S/N Ratio Image & Spurious Rejection Receiving Sensitivity AF Response T.H.D. IF Frequency Dynamic Range Tone Signal Audio Output Power Supply Current Consumption Dimension(MM) WxHxD Weight
:
: Half 19 EIA Rack Metal Case
: PLL Synthesized
: FM
: 100dB, at 20KHz deviation and 60dBV antenna input
: 70dB minimum
: At 2V over 52dB S/N ratio
: 80Hz to 18KHz
: 1% (at 1KHz)
: 1st: 243.95MHz 2nd: 10.7MHz
: 100dB
: 32.768KHz
: Balanced & Unbalanced
: DC12V
: 26010mA
: 200x42x183
: 930g Handheld/Bodypack Transmitter Frequency Range Channel Select Display RF Power Output Frequency Stability Spurious Emission Gain Setting Mic Unit Battery Current Consumption Dimension(mm) WxHxD Weight
: 520-608 MHz, 614-617 MHz, 652-663 MHz
: SYNC with Receiver
: LCD displays status of channel, battery :
10mW (max.)
: 0.005%
: 60dB below carrier frequency Bodypack : 0dB, -10dB, -20dB (3 settings) Handheld : Uni-Direction dynamic unit or Uni-Direction electret condenser unit Bodypack: Lavalier Mic / Headset Mic
: 1.DC2.4V(1.2V x 2AA size rechargeable batteries) 2.DC3V (1.5V x 2AA size batteries)
: 12010mA Handheld : 260x54 Handheld : 234g Bodypack : 65x97x25 Bodypack : 86g 440-0100-02 18