R 433,42 MHz User manual :
ARCO / ARCO 2 / ARCO 5 ARCO 10 / ARCO 20 9 1
. 4 0
. 2 1 _ 4 0 v e r Dear Customer, thank you for purchasing a MASTER S.p.A. product. This guide contains all the information you will need concerning the use of this product. Read the instructions carefully and keep them for further consultation. ARCO is designed to be coupled with MASTER S.p.A. receivers. All other use beyond the field defined by MASTER S.p.A. is forbidden. This, as well as the breach of the instructions given in this guide, shall release MASTER S.p.A. from any liability and shall annul the product warranty. Water, humidity, heat sources, accidental falls can damage the device. Do not use abrasive products or solvents to clean the product. Package contents
- 1 transmitter ARCO5 - ARCO10 - ARCO20
- 1 CR2032 lithium battery
- 1 wall bracket
- 2 dowels
- this manual This transmitter complies with FCC (Federal Communications Commission) Part 15. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operatio. Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC ID:
2ASK4ARCO All products and technical specifications given in this document are subject to variation without notice. Unless previously and specifically authorised by the manufacturer, the device must be used exclusively with receivers produced by the same manufacturer. The manufacturer shall not be liable for damage resulting from improper, incorrect or unreasonable use. MASTER S.p.A. via S.Pertini 3, 30030 Martellago (VE) www.mastermotion.eu Disposal At the end of the product life cycle, dispose of the device in compliance with local regulations. This product could contain substances that are harmful to human health and in the environment: do not dispose of domestic waste. the product Technical specifications
- Power supply:
- Operating temperature:
- Operating frequency:
- Operating frequency band:
- Max radiated power, e.r.p. :
n 1 CR2032 lithium battery 0 C / +55C 433.42 Mhz 433,050 434,790 Mhz
<10 mW
- N of channel ARCO:
- N of channels ARCO2:
- N of channels ARCO5:
- N of channels ARCO10: 10 + sequencer channel
- N of channels ARCO20: 20 + 4 groups 1 2 + sequencer channel 5 + sequencer channel Notes on radio system Do not use radio systems in places with strong interference (for example, near police stations, airports, banks, hospitals). It is in any case advisable to carry out a technical inspection prior to installing any radio system in order to identify possible sources of interference.Radio systems can be used where any disturbances or malfunction of the transmitter or receiver do not constitute a risk factor, or if such factor is eliminated using appropriate safety systems.The presence of radio devices working at the same transmission frequency (433.42 MHz) may interfere with the radio receiver and reduce the range of the system, limiting functionality. Fixing the wall bracket A) Fix the bracket to the wall using the supplied plugs (distance between holes 36 mm). B) Cover the screw heads with the coverage provided. C) Hang the transmitter to the support. Battery insertion /replacement The transmitter is powered by a battery C R2032. To insert the battery, remove the battery cover on the back of the transmitter, insert the battery Use of batteries different than respecting the polarity, close the cover. those referred can cause an explosion hazard. Used batteries must It it recommended to replace be discarded in appropriate containers. the battery every 2 years. 1. ASSOCIATED FUNCTIONS AT BUTTONS Basic functions up stop down channel - / prev channel + / next right orientation left orientation SUN On/Off MENU FOR ME PROG access to the receiver menu transmitters insertion-deletion MENU PROG Favorite position Press STOP To memorize:
and then FOR ME and hold the buttons until the motor signalation (about 5 seconds) To recall:
Sun / Automatic lowering function By the SUN On / Off " button you can activate / deactivate the SUN function or the AUTOMATIC LOWERING function, in the receivers equipped with these functions. To modify the setting:
A) Select the channel (excluded sequencer channel and groups) YELLOW Led B) Press until the state of the yellow LED varies (about 2seconds) C) YELLOW LED IS ON If
: sun/automatic lowering function active In ARCO2 the channels: if you enable it for channel 1, it is NOTE:
automatically activated for channel 2 and viceversa It is possible that some receiving devices do not associate any operations to some transmitter buttons or that associate to the transmitter buttons some operations different from what it is described. In this case consider the instruction manual of the receiving device. Sun/Automatic lowering function is active for both Advanced functions Pulsante MENU
: permette di accedere velocemente alla configurazione dei parametri del ricevitore. Fare riferimento al manuale duso del ricevitore per le procedure. Pulsante PROG telecomandi. Fare riferimento al manuale duso del ricevitore per le procedure.
: permette linserimento/cancellazione del telecomando nella memoria del ricevitore. Se il telecomando gi memorizzato, permette la memorizzazione di ulteriori 2. ENABLING/DISABLING GROUPS AND CHANNELS With transmitters ARCO 5, ARCO 10 and ARCO 20 you can turn off the channels that are not used; this will facilitate the use of the transmitter because when you scroll through the list of channels, you find only those actually used. It's possible, with the same procedure, reactivate the channels. The procedure is as follows:
. will appear. and hold the buttons for about 3 seconds, until the STOP and then MENU STOP 01 YELLOW LED IS ON channel/group enabled RED LED IS ON channel/group enabled A) Press Press B) C) If Press D) E) If necessary,press PREV and NEXT to select another channel/group and return to point C. F) To exit, or wait about 15 seconds (the display switches off). to modify the setting. press twice MENU STOP ch
/ If
:
:
symbol is displayed. 3. DELAY OF TRANSMISSION ON GROUPS AND SEQUENCER CHANNEL RED Led YELLOW Led
, scroll the list of channels until ARCO 2, ARCO 5 and ARCO 10 Sequencer selected command in succession for all the active radio channels belonging to the group. To select a group, scroll the list of channels until the symbols G1, G2, G3 and G4 appear. It is possible to set the interval (from 1 to 10 sec) of time which must pass between the transmission on one channel and the next. The factory sets the delay at 1 second. The use of high intervals of time can negatively effect on the battery life. To modify the setting:
, which sends the selected command in succession for all active radio channels. To select the
) which send the Sequencer transmitter is equipped with 4 virtual channels (called transmitters have a virtual channel called ARCO 20 symbol appears. The G1 G2 G3 G4
, indicated with Groups SE
,
,
, A) B) C) D) E) F) Press Press Press Use Press To exit, STOP and then MENU NEXT STOP Sd
. The
. The currently set value appears on the display (from 01 to 10 sec). symbol appears on the display. and hold the buttons for about 3 seconds, until the ch symbol is displayed. PREV and NEXT to set the required value. STOP to save the setting. press 1 time MENU or wait about 15 seconds (the display switches off). 4. SETTING THE CHANNELS BELONGING TO A GROUP (only ARCO20) G1 G2 G3 G4 transmitter is equipped with 4 virtual channels (Groups, indicated by The belonging to the group. It is possible to associate up to 20 channels to each group. To set different groups, follow the procedure:
ARCO 20
,
,
,
) which send the selected command in succession for all the active radio channels G1 STOP and then MENU and hold the buttons for about 3 seconds, until the symbol appears on the display. To select another group press NEXT. A) Press B) C) D) YELLOW LED IS ON: channel belongs to the group RED LED IS ON channel not belongs to the group E) F) G) Press twice NEXT. Press STOP. Channel 01 appears. If Press If necessary, press PREV and NEXT to select another channel and return to point E. To exit, or wait about 15 seconds (the display switches off). to modify the setting. symbol is displayed. press twice MENU STOP ch
/ If
:
RED Led YELLOW Led