FCC ID: TKCBT-150 STAKE Bluetooth Extended Range

MODEL # BT-150 STAKE Bluetooth Extended Range Truly Wireless Thermometer Quick Start Guide Introduction Thank you for choosing our product, MODEL BT-150. Please read the information in this Quick Start Guide before using the product. Important Notes Please read this carefully before use This product is exclusive for cooking meat/food in a grill or oven. It should only be used as described in the User Manual. This product is not intended for use by people ages 12 and under. It is required to insert the STAKE properly into the charging compartment of BT-150 repeater for charging. Please make sure the pole of STAKE and the charging pin is properly contact while charging. It is required to insert the STAKE properly into the meat/food during cooking. Do not expose the metal part of the STAKE to the heat generated by grill/oven directly. To obtain the best result, please make sure the tip of the STAKE is located at the center (or the thickest part) of the meat/food. Do not use the STAKE in a microwave oven. DO NOT TOUCH THE STAKE WITH BARE HANDS JUST AFTER COOKING. Always wear oven gloves to remove the STAKE from the meat/food after cooking. When the temperature is higher than the overheat threshold (212 F/100 C), an overheat alert will be triggered. Remove the STAKE immediately from the heat source with oven gloves. The STAKE can be washed in water but do not immerse for more than a few seconds. Do not recharge the STAKE until it has cooled down to room temperature. The STAKE has normal bluetooth range of 30 ft to your phone. The BT-150 repeater receives the bluetooth signal instead of your phone and repeats it up to 150 ft to your phone. These are clear line of sight ranges and will be reduced if obstacles are in the path of the RF signal. 1. 2. The BT-150 repeater is not waterproof. Take out the battery from BT-150 repeater whenever it is not in use for long periods. Turn off the BT-150 and save the battery power by sliding the switch to the USB position. Maverick will not be liable for any damage of the product due to misuse of the device. BT150 QSG Page 1 Slide the side switch to BAT position The LED will be flashing slowly 3. Getting Started 3.1 Insert Battery into BT-150 repeater Slide the side switch to USB position Take out the battery door Insert a new AAA size battery Put back the battery door 3.2 Turn ON BT-150 repeater PS: To save power, slide the side switch to USB position to switch off the device or take out the battery when it is not in use. 3.3 Charging the STAKE Put the STAKE into the charging compartment The LED will then be flashing quickly. When the STAKE is charged, the LED will stay ON for about 2 seconds and go off. The STAKE is ready to use now !!!

3.4 Download the app Download the latest version of APP (STAKE) from Apple APP Store or Google Play (or scan the QR code in the right hand side) Support E mail help@maverickhousewares.com Regulation & Compliance For information regarding Regulation and of the Compliance (e.g. FCC ID), tap the setting icon APP and select Regulation & Compliance. 4. 5. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. RF exposure statements 1. 2. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This Transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. BT150 QSG Page 2

FC #

FCC ID: TKCBT-150 pores Ua Ue On Output 3VDC 0.3A Made In China 2 Silkscreen: Silver PMS 10077 FCC ID: TKCBT-150 Model: BT-150 Input 5VDC 0.5A Output 3VDC 0.3A Made in China 13.1 mm Silkscreen: Silver PMS 10077 FCC ID: TKCBT-150 ree oot) Input SVDC 0.5A Output 3VDC 0.3A Made In China

Maverick Industries, Inc. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: TRCBT-150 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name

(ie- Block Diagram, Schematics, Operational (ie- 10. Block Diagram, 11. Schematic Description) Diagram, 12. Circuit Description) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely,

(signature) .

(printed name) Darren Keller Rev 11/20/07

Maverick Industries, Inc. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021-03-09 SUBJECT: FCC Application for FCCID: TKCBT-150 To Whom It May Concern:

We, the undersigned, hereby authorize Willa Lan at A Test Lab Techno Corp. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Willa Lan on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(Must be signed by the person that is listed on the FCC Website) Company Name: Maverick Industries, Inc. Contact Person: Darren Keller Signature:

\ lf, i, ow i LA ae Sonne C:\Users\dk\Documents\BBQ\BT-30 STAKE\FCC\BT-150 FCC\POA_Letter.docx

Maverick Industries, Inc. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021-03-09 FCC ID: TRCBT-150 SUBJECT:

To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. J understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetef/eas/reports/TestFirmSearch.cfm (Select the accredited option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, Maverick Industries, Inc. Darren Keller