FCC ID: 2AUIF-VT-07863 DRONE S106

FCC Caution:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to Consult the dealer or an experienced radio/TV technician for help. which the receiver is connected. FCC Radiation Exposure Statement:

For DRONE S106:

this equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

Project No. : SZ3220614-26225E-RF EXHIBITA-FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the time purchase (Labeling requirements per 2.295)

Max Sales Group 15240 NELSON AVENUE CITY OF INDUSTRY,Los Angeles California United States 90040 Tel: 323.722.4200 E-Mail:tarun@maxsalesgroup.com Attestation Letter Date: 2022-08-01 To:

FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

The RF chip, model BK7231U, installed in our product: Product Name: DRONE S106

, Model number: VT-07863, FCC ID: 2AUIF-VT-07863, which support 802.11b/g/n. But for marketing purpose, this chip in this product only supports 802.11g. The other mode and channel has been shielded by the manufacturer by using the software. Sincerely Yours, Signature:

Printed Name: Tarun Khiani Title: Purchase Manager

1. When the battery supplies power to the UAV, it supplies power to the main control chip through the voltage regulator. When the main control chip receives the Control Command sent by the launch, the main control chip will correspond to the Control Command. 2. The 2.4g module receives the signal from the transmitter through the antenna and processes it, and then provides it to the main control for decoding. 3. After decoding, the main control firstly controls the signals coming from the emitter and outputs them to motor driving circuits to drive the aircraft for action 4. After take-off, the main control firstly detects the gyroscope and barometer, and compensates them according to their status to make them hover stably at a fixed height in mid-air 5. After the initial completion of the flight status, you can carry out any flight movements according to the transmitted signals. The Wi-Fi module (BK7231U) is connected to the driver chip, and the radio frequency chip inside the Wi-Fi module performs signal acquisition and control to realize signal transmission. requency Range:2412-2472MHz Modulation:OFDM Crystal oscillator:26MHz 2.4 G SRD frequency:2402-2480MHz

(RC Receiver is only receive function)

Max Sales Group 15240 NELSON AVENUE CITY OF INDUSTRY,Los Angeles California United States 90040 Tel: 323.722.4200 E-Mail:tarun@maxsalesgroup.com 7/13/2022 FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

hereby authorize Shenzhen Accurate Technology Co., Ltd to act on We, Max Sales Group its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, This authorization is valid until further written notice from the applicant. 21 U.S.C. 862. Sincerely Yours, Signature:

Printed Name: Tarun Khiani Title: Purchase Manager QA-FR-170-B