SP-1000 Series User Manual
"Professional Radio Products"
MAXONCIC Corp. Chongho Bldg, #7-6, Yangjae-Dong, Seocho-Ku, Seoul, Korea Tel : +82-2-3498-3114 Fax : +82-2-3498-3113 www.maxoncic.com User Instruction Manual User Instruction Manual Battery Charging and Care To ensure peak performance from your radio, the battery pack must be fully charged. Proper care and charging will allow maximum performance and life of your battery pack. Desktop Charger provides 2 hours charging to one radio and/or one battery. Attaching and Removing the Belt Clip To Install:
Slide the Belt Clip downward until a click is heard. To Remove:
Pinch the inside clip and then slide the belt Clip upward. 1 PUSH 2 2 1 PUSH Attaching and Removing the Jack Cover To Install:
Affix the jack cover by a screw until the screw is fully tightened. To Remove:
Loosen the screw until the jack cover is detached from the radio in order to use any accessory for SP-1000 1 2 1 2 User Instruction Manual Status Indicators and Audible Alert Tones Your SP-1000 Series has a sophisticated microprocessor control which provides a series of audible alert tones. Upon initial power up, a quick melody indicates that the self-test of the microprocessor functions has been completed satisfactorily. A series of tones may be sounded with any of the following conditions:
Attempt to transmit on a channel set for receive only Attempt to transmit on a channel that is already in use when busy channel lockout has been programmed into the radio *
Transmitting time has exceeded time-out timer programmed length *
Low battery condition Selecting a channel with no programmed frequency Indicates a function that is initially programmed into the radio by your Maxon Dealer. NOTE: All audible tones can be programmed off for silent operation. Status Normal Description LED color Audible Tone Power On - Ready Call Received Correct Call Busy Channel Transmit N/A Orange Green Orange Red Melody N/A N/A N/A N/A Two beeps N/A 2 beeps repeated 2 beeps repeated Two beeps Single beep/3 beeps repeated Two beeps BATTERY ONLY Scanning Warning Transmit not allowed Red Flashing Normal Scan mode Green Flashing Red Flashing Low Battery Busy Channel lockout Orange TX Inhibit Time-out-timer Error Unlock N/A N/A N/A User Instruction Manual Table of Contents Synthesized Scanning Radio Operating Instructions About Your SP-1000 Series Radio SP-1000 Series Specification Safety Information Unpacking Information SP-1000 Series Features Description of Radio Components Antenna Installation Installing and Removing the Battery Pack Attaching and Removing the Belt Clip Attaching and Removing the Jack Cover Battery Charging and Care Status Indicators and Audible Alert Tones Operation Mode Power Off Mode Power On Mode High / Low Power Cloning Password Fixed Key PTT MONITOR EMG Licensing and Service Information FCC Licensing Service Recycling/Disposal of Batteries Software Copyrights Maintenance Limited Warranty CHL-100L Desktop Regular Charger 2 3 3 3 4 5 6 7 8 9 10 10 11 12 13 13 13 13 13 13 13 14 14 14 15~17 15 15 15 16 16 17 18~20 1 User Instruction Manual User Instruction Manual Synthesized Scanning Radio FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR OCCUPATIONAL USE ONLY The Federal Communications Commission (FCC), with its action in General Docket 93-62, November 7, 1997, has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Proper operation of this radio will result in user exposure far below the Occupational Safety and Health Act
(OSHA) and Federal Communications Commission limits. DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. This radio is NOT approved for use by the general population in an uncontrolled environment. This radio is restricted to occupational use, work related operations only where radio operator must have the knowledge to control the user's exposure conditions for satisfying the higher exposure limit allowed for occupational use. When transmitting, hold the radio in a vertical position with its microphone 1 inches (2.5 cm) away from your mouth. The radio is transmitting when the red LED on the front of the radio is illuminated. You can cause the radio to transmit by pressing the PTT bar on the radio. These are required operating configurations for meeting FCC RF exposure compliance. Failure to observe these restrictions mean violation. FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This devices may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Operating Instructions About Your SP-1000 Series Radio Maxon's SP-1000 Series radio feature up to 16 channels. Operation and functions for these radios are described in this manual. We urge you to thoroughly read this manual before operating the radio. Application of some of the functions described in this manual is determined by the system you use. Your Maxon Dealer will program your radio so that you have the greatest number of functions possible relative to your needs. Should you have questions regarding the operation of the radio please consult your Maxon Dealer. SP-1000 Series Specification MODEL EQUIPMENT TYPE PERFORMANCE SPECIFICATIONS SP-1102 SP-1402 Hand-portable TIA/EIA-603 BAND CHANNEL SPACINGS RF OUTPUT POWER MODULATION TYPE AUDIO POWER VHF(148~174MHz) UHF(440~470MHz) 12.5kHz / 25kHz PROGRAMMBLE 5 / 1 WATT F3E 500mW ( EXT WITH 8 OHM) 1W ( INT WITH 4 OHM) INTERMEDIATE FREQUENCIES CHANNELS FREQUENCY SOURCE POWER SUPPLY 45.1MHz 455kHz 16 Channel SYNTHESIZER Li-Ion(1500mA) 7.5 VDC NOMIN
+/- 10% VDC EXTRE User Instruction Manual User Instruction Manual Safety Information The Federal Communications Commission (FCC), with its action in General Docket 79-144, March 13, 1985. Has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Maxon subscribes to the same safety standard for the use of its products. Proper operation of this radio will result in user exposure far below the Occupational Safety and Health Act and Federal Communications Commission limits. WARNING -
DO NOT hold the radio in such a manner that the antenna is next to, or touching, exposed parts of the body, especially the face or eyes, while transmitting. WARNING -
DO NOT allow children to operate transmitter -
equipped radio equipment.
CAUTION -
DO NOT operate the radio near unshielded electrical blasting caps or in an explosive atmosphere unless it is a type especially designed and qualified for such use.
CAUTION -
DO NOT press and hold the transmit switch (P-T-T) when not actually wishing to transmit NOTE: This radio operates in FCC regulated frequency bands. All radios must be licensed by the FCC before use. Because this radio contains a transmitter, federal law prohibits unauthorized use or adjustments of this radio. Unpacking Information Remove and carefully inspect the contents of your package(s) for the following items:
1 2 3 4 5 6 7 8 Jack Cover Radio Battery Pack Battery Charger Spring Belt Clip Antenna Battery Charger Power Supply Operating Instructions If any items are missing, please contact your Dealer or Maxon. 1 2 4 5 6 3 7 8 User Instruction Manual User Instruction Manual SP-1000 Series Features Wideband frequency separation 1 or 5 W programmable output power Programmable 12.5/25 kHz channel spacing Channel scan Priority channel scan Look back channel CTCSS/DCS tone signaling 2-Tone Decode Busy channel lockout Time-out timer Priority Channel Edit Description of Radio Components 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Antenna Receptacle Channel Selector Switch On/Off - Volume Control Emergency Button Push-To-Talk (PTT) Monitor Button Option Button Battery RX/TX Indicator Speaker Microphone Accessory Connector (EXT Jack) Battery Latch Belt Clip Battery Charge Contacts 1 2 3 12 13 14 4 5 6 7 8 9 10 11 15 User Instruction Manual Antenna Installation Fasten the antenna to the radio by turning the antenna clockwise into the receptacle on top of the radio 2 1 2 1
! CAUTION NEVER HOLD by the antenna when carrying the transceiver. Transmitting without an antenna may damage the transceiver. User Instruction Manual Installing and Removing the Battery Pack To Install:
Connect the bottom of the battery to the rear and bottom of radio and fold it into the radio until a click is heard. To Remove:
Press the button on the top of the battery and pull the battery out from the Radio. 2 1 PUSH 1 2 2 3 4 5 6 7 8 9 User Instruction Manual Operation Mode This section provides general descriptions of the operating modes of the SP-1000 Series Radio. Power Off Mode The SP-1000 Series shall enter Off mode when the On/Off Volume knob is rotated to the most counter-clockwise position beyond the detent. Upon entering Off mode, the radio shall store its current channel (if Power On Channel function is disabled via PC programmer). Power On Mode The SP-1000 Series shall enter Power-On mode when the On/Off Volume knob is rotated clockwise beyond the detent. Upon entry of the Power-On mode, the radio shall perform the 1 time power-on alert to indicate that it has been turned on High / Low Power The radio shall be capable of programmable output power. Each channel can be programmed via pc programmer to have either high or low power. It can also be set by pressing the option button. Cloning Frequencies and functions can be programmed from radio to radio by using a cloning cable. Password If the password function is enabled, the user must enter a password for the radio to become operational. You can enable the password and set the password code by using the PC programmer. You can also set the password enable/disable by a programmable key (password and menu option). At this time you can enter the password code by using the EMG/PTT/MON/OPTION button in the correct sequence. Four button presses are required to enter the code. If the code is not correct, the LED will blink red and there will be a double beep repeated. To disable the password function, you can select On/Off by using the PC programmer. The default is disabled. Fixed Key User Instruction Manual PTT Press and Hold to transmit. Release to receive mode. Power on with press and holding PTT Key to see software version 1 2 MONITOR Releases the squelch and tone circuit to check whether the channel is busy.
(OPTION) Short pressing: Enable/Disable Scan Look Back channel edit Tx power H/L EMG Transmit EMG ID 5 times and generate warning audio alert during seven seconds Licensing and Service Information User Instruction Manual FCC Licensing The Federal Communications Commission requires that the operator of this radio be properly licensed under the applicable Part and/or Parts of the FCC Rules and Regulations. Consult with your Maxon Dealer, or contact the nearest FCC Field Office for information about obtaining a license. Service Do not tamper with internal adjustments. Damage to the equipment and/or improper operation may result. There are no user serviceable items inside the radio. It is recommended that you return your radio to a qualified Maxon Dealer for any service or repairs. Recycling/Disposal of Batteries The battery should be recycled at the end of its useful life. Under various state or local laws, such batteries must be recycled or disposed of properly and cannot be dumped in landfills or incinerators. For further information on how to safely dispose of your used batteries
,contact your Maxon Dealer. User Instruction Manual User Instruction Manual CHL-100L Desktop Regular Charger Operating instruction User Instruction Manual User Instruction Manual Software Copyrights The Maxon products described in this operating instruction manual may include copyrighted Maxon software programs stored in semi-
conductor memories or other media. Laws in the United States and other countries preserve for Maxon certain exclusive rights for copy-
righted software programs, including the exclusive right to copy or reproduce in any form the copyrighted software program. Accordingly, the copyrighted Maxon software programs contained in the Maxon products described in this operating instruction manual may not be copied or reproduced without the express written permission of Maxon. Furthermore, the purchase of Maxon products shall not be deemed to grant either directly or by implication , estoppel, or otherwise, any license under the copyrights, patents or patent applications of Maxon, except for normal non-exclusive royalty free license to use that arises by operation of law in the sale of a product. Maintenance Your SP-1000 Series Radio is designed to be maintenance free. To keep your radio in good working condition:
Clean external surfaces with a clean cloth dampened in a solution of dishwasher detergent diluted in water. Apply the solution sparingly to avoid any moisture leaking into cracks and crevices. Do not submerge the radio. Use a non-metallic brush to dislodge stubborn particles, if necessary. Dry the surface thoroughly with a soft, lint free cloth. DO NOT use solvents or spirits for cleaning - they may permanently damage the housing. Clean the battery contacts on the back of the radio with a lint free cloth to remove dirt, grease, or other foreign material that may impede good electrical contact. Limited Warranty Maxon shall have no obligation to make repairs or to cause replacement required which result from normal wear and tear or necessitated in whole or in part by catastrophe, fault or negligence of the user, improper or unauthorized alterations, repairs to the Product, use of the Product in a manner for which it was not designed, or by causes external to the Product. This warranty is void if the serial number is altered, defaced or removed. THE EXPRESS WARRANTIES CONTAINED HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FOR ANY PRODUCT WHICH DOES NOT COMPLY WITH THE WARRANTY SPECIFIED, THE SOLE REMEDY WILL BE REPAIRED OR REPLACEMENT. IN NO EVENT WILL MAXON BE LIABLE TO THE BUYER OR ITS CUSTOMERS FOR ANY DAMAGES, INCLUDING ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, OR FOR THE LOSS OF PROFIT, REVENUE OR DATA ARISING OUT OF THE USE OF OR THE INABILITY TO USE THE PRODUCT. Product description The CHL-100L is Regular Charger for Maxon's SP-1000 Series Two-way radio batteries. The charger has been designed to fully charge only the Li-Ion, 1500mAh battery, the front charging slot charges a battery while connected to the radio, the back charging slot charges a battery that has been removed from the radio. Orientation Plug the AC adapter cable into the adapter jack locked on the rear of charger. Plug the AC adapter into an AC outlet LED Charger. Remove the charger base and AC adapter from packaging. Plug the AC adapter cable into the adapter jack located on the rear of the Plug the AC adapter into an AC outlet. Your charger is now ready to begin charging Charging starts automatically when the radio equipped with battery is in place. The charging time is approx 10 hours or less, depending upon the leftover capacity, current charge status of the battery Lighting color Red Green Blinking orange Blinking red Description During charging Fully charged Extreme cold(under -10 C; 14 F) Extreme heat(over +60 C; 140 F) Error NOTE: If your battery seems to have no capacity even after being fully charged, completely discharge them, then fully charge them again. If they still do not retain a charge, new batteries must be purchased. Safety information To reduce the risk of shock or injury, familiarizes you with the proper and safe operating procedures defines in this manual. Only charge Maxon's battery in this charger - other battery types may burst causing personal injury/or damage to the charger, battery or radio. The CHL-100L desktop charger is rated for indoor use only. Do not disassemble the charger, incorrect reassembly can cause fire or electric shock. Do not pull output plug with excessive force. User Instruction Manual Do not use the charger when it is covered by objects which impede heat dispersal. Connect the supplied Maxon adapter only to the voltage supply as specified on its label. Unplug the AC adapter from wall outlet before attempting inspection or cleaning of the charger. Do not use solvents such as benzene or paint thinner to clean the charger. MEMO 10 11 12 13 14 15 16 17 18 19 20