User Manual CHARGER ASSY-WIRELESS QF 4CH58-AP000/010 p
*This product was designed for Kia Motors OPTIMA(QF).
*Only Qi-certified device can be charged on this product. Q g Thank you for purchasing this wireless vehicle charger for Kia Motors OPTIMA(QF). Please read the user manual carefully and use the product safely. d h f ll f l d d h l l Power LED Charge LED Description of parts No Coins No Smart key QI Logo Rubber Pad NOTE Qi Logo: This product is Qi-certified wireless charger. No Smart Key: Do not put a smart key on this product. No Coins: Do not put the coins on this product. No Coins: Do not put the coins on this product. H How to use t 1. Turn on the engine, and see if the product's power LED(right) is lit. 2. Place the device that has the Qi logo on the middle of the charging pad. (Is better to align the device to the center of the pad) 3. The Charge LED starts to light on in red as charging begins. 4. When the charging is finished, the LED will turn green. If it is not charging well make sure to align the device to the center and recharge. Some smartphones or cases do not send the full charging signal to wireless charger, in this case, the charge LED will remain in red. Troubleshooting Troubleshooting The device is not charging
- Make sure the device is qi standard.
- Relocate the device location.
- Make sure the device being charged is full.
- Make sure that something is on the wireless charger. g g The charge LED is blinking fast or not lit
- Make sure you have properly connected your device with the appropriate wireless charging case, or foreign objects are inserted between receiver and transmitter.
- Relocate the device location. Caution, Service t t i Do not put a smart key or coins on this product. Do not insert or wet with water or any other liquid. D Do not take it part or make alterations. Keep away from any mechanical device that could be affected by a magnetic field. ith th id li t t 1. Put a mobile phone in the middle of the product to charge. If the mobile phone is placed in other position, it may cause charge malfunction malfunction. 2. The use of original Rx Case is recommended for this equipment. If any abnormal RX Case is used, it may cause malfunction or damage of the equipment. 3. If there are any metal materials like coins between chargers, you may suffer physical injuries including burns due to heat. If you encounter problems or abnormalities during the use please If you encounter problems or abnormalities during the use please stop using the product and contact the store where the purchase was made. C Compliance Statement S li FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. p p g g This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to Part 15 of the FCC Rule s. These limits are designed to provide reasonable protection agai nst harmful interference in a residential installation. This equipmen t generates uses and can radiate radio frequency energy and, if no t installed and used in accordance with the instructions, may caus e harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tr y to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. C Consult the dealer or an experienced radio/TV technical for help. l h d l di /TV h i h l l f d i C Compliance Statement S li IC Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licen ce standard RSS (s). L'opration est soumise aux deux conditions s uivantes: (1) cet appareil ne peut causer d'interfrences, et (2) cet appareil doit accepter toute interfrence, y compris les interfrenc es quipeuvent causer un mauvais fonctionnement de l'appareil.
( ) p Users Caution Statement Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void users authority to operate the equipment. Toute chang ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'utilisateur `autorit de faire fonctionner cet quipement.