6.)DISPLAY MODES:
There are two display modes in display unit. 6.1.)Auto Scan Display Mode:
In this mode the display will show the pressure of the Front Left tire, Front Right tire, Rear Left tire and Rear Right tire switching to each tire one by one in each 3 seconds. To indicate the tire and the correspo-nding readout a LED on the car symbol on top to the LCD will light up. To indicate the pressure condition, while you see the actual readout on LCD the LED light will also show you the status of your tires by changing it's colors at different thresholds in following manner. RED- When tire pressure is too low, 20% below set limits YELLOW- When tire pressure is between 10% and 20% below set limits GREEN- When tire pressure is normal, between -10% and +20% of set limits BLUE- When tire pressure is too high, over 20% of set limits In this mode if you need to see the actual pressure of any tire you can manually select the tire by pressing UP or DOWN buttons. Once you manually select a tire after 10 seconds the display will enter to scan the tires one by one in each 3 seconds. 6.2.)Manual Scan Display Mode:
While you are in Auto Scan mode press MODE button will switch the display to manual display mode. To indicate this mode LED corresp-onding fo the selected tire will blink. In this mode the display will fix to one tire permnently. If you want to see the next tire should press UP or Down buttons and manual move to next tire. See fig.6 for a layout of basic display format of tire pressure. LED to show the current u , Tower symbol display ti isplay tire to show the receiving of RF signals 7.)SPECIAL DISPLAY FEATURES:
This tower symbol shows the status of RF signal reception. If your display unit received signals within last 60 minutes this symbol will always on. If no signals received in last 60 minutes tower will blink. If no signal is being received in last 3 hours tower display will disappear. yw om (9) pa Bat ( a Tower symbol:
Pe YN 1 ca ar) a Fig.7 Low battery display:
The batteries in the valve caps require change about once a year. If the word Lo appears at left bottom window on the display you should replace the button cells of valve caps immediately. 8.) SPECIAL ALARM ALERTS:
There are special Buzzer alarms to indicate different alarming conditions of tire pressure. A BEEP in each 4 seconds 1.) | Sudden drop in pressure 2.) | Pressure less than 80%
3.) Did not receive data from valve cap for more than 2 hours You can press any key while the alarm is beeping the alarm will stop immediately. Two BEEPS in each 4 seconds:
No data received from a valve cap for last 5 hours. 9.) If your TPMS cannot receive signals If your TPMS does not display tire pressure for over one hour please reset the unit by pressing the RESET switch at the right side of the unit as shown in Fig.1 Recommendation:
1) As the caps may protrude beyond the tire wall please take extra care when parking or using an automatic car wash,for example,in order to prevent any damage. 2) Some wheels may require rebalancing if the user feels that the tires are out of balance, When rotating tires, the caps must remain in the same location as originally installed for proper signal transmission to the receiver. Please refer to Original Manufacturers Owners Manual. 10.)Battery Notes:
e@ Replace all batteries of a set at the same time
@ Clean the battery contacts and also those of the device prior to battery installation. e@ Ensure the batteries are installed correctly with regard to polarity
(+ and -)
@ Remove batteries from equipment which is not to be used for an extended period of time Caution for Boat Trallers:
Valve caps cannot submerge in water for longer periods. All valve caps should be removed from tires during launching and loading boats onto trailers. HELPFUL HINTS:
e Always be sure to follow the tire manufacturers recommended tire pressure ratings which are based on cool tire temperatures. This information can be found either in the owners manual or on the drivers door jam of your vehicle.
@ Toclean the gauge, use a soft damp cloth. Do not immerse in, or spray with water or other liquid cleaners. FCC wamings:
This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
@ Reorient or relocate the receiving antenna. e@ Increase the separation between the equipment and receiver.
@ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
@ Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the manufacturer of this product and the party responsible for compliance could void the users authority to operate the equipment. Warranty and service Measurement Ltd, Inc. (MLI), warrants for a period of one (1) year from date of purchase that the product will perform substantially in accordance with its written specifications. MLI does not warrant that the product will meet the specifics needs of purchaser or that the product will be fit for use on all vehicles, and purchaser shall be responsible for determining whether the product is appropriate for purchasers desired application or vehicle. Other than the foregoing express warranty, MLI makes no other warranty with respect to the product or the results that may be obtained from the use of the product, and MLI hereby disclaims all other warranties, including the implied warranties of fitness and merchantability. In the event of a breach of the foregoing warranty, purchasers sole remedy will be a full refund of the purchase price paid. Under no circumstances shall MLI be liable to purchaser for any incidental, indirect or special damages resulting from the use of the product including, without limitation, for any damage to purchasers vehicle. Some states do not allow the limitation or exclusion of implied warranties, so the above limitation or exclusion may not apply. Our authorized service center address:
2001 Route 46,Suite 310 Parsippany, NJ 07054 Attn: Customer Service Measurement Ltd.,Inc. www.measurement-Itd.com MODEL MS-4378 Printed in China