Home Theater Projector INSTRUCTION MANUAL MODEL NO.: PJ132 Email: support@SRIAXNOL.com PLEASE READ BEFORE OPERATING THIS EQUIPMENT Important Safety Instructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplier) that product heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Only use attachments/accessories specied by the manufacturer. 11. Unplug this apparatus during lightning storms or when unused for long periods of time. 12. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 1 Additional Warnings and Precautions 1. Do not look directly into the projector light. 2. Dont touch the project lens. 3. Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. 5. WARNING: Changes or modified to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 6. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. 7. WARNING: Shock hazard - Do Not Open. 8. Caution and marking information is located at the rear or bottom of the apparatus. 9. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing. 10. Objects filled with liquids, such as vases, shall not be placed on the apparatus. 2 FCC Warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In The Box AC Power Adapter Cleaning Cloth Main Unit Home Theater Projector INSTRUCTION MANUAL MODEL NO.: PJ132 Email: support@SRIAXNOL.com PLEASE READ BEFORE OPERATING THIS EQUIPMENT Lens Cover Remote HDMI Cable User Manual 3 Table of Contents Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P1 Additional Warnings and Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P2 FCC Warning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 In The Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 Table of Contents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P4 Remove & Close The Lens Cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P5 Placing of Your Projector - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P5 To reduce Image Distortion - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P6 Distance Between The Projector And Screen - - - - - - - - - - - - - - - - - - - - - - - - P6 Installing Your Projector in the Ceiling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P6 Adjust The Vertical Location - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P7 Adjust The Focus And Keystone - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P7 Controls of Remote - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P8 Install / Remove Batteries of Remote - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P8 Controls of Projector - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P9 Install Power Adapter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P10 Main Button Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P10 Connect HDMI Show The Image On Projector Screen - - - - - - - - - - - - - - - - - P11 Connect AV Show The Image On Projector Screen - - - - - - - - - - - - - - - - - - - P11 Connect VGA Show The Image On Projector Screen - - - - - - - - - - - - - - - - - P12 Connect Audio Output (Aux Out / Line Out / Earphones) - - - - - - - - - - - - - - P13 Install USB Device And TF (Micro SD) Card - - - - - - - - - - - - - - - - - - - - - - - - P13 Using TF Card And USB Playback (Media Player) - - - - - - - - - - - - - - - - - - - - P14 Using Bluetooth Playback - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P15 Multi-screen interactive connection for phone and projector - - - - - - - - - - - P16 WiFi Connection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P16 Screen Mirroring for Android System (With WiFi) - - - - - - - - - - - - - - - - - - - - P16 Screen Mirroring for Android System (Without WiFi) - - - - - - - - - - - - - - - - - P16 Screen Mirroring for iOS System (With WiFi) - - - - - - - - - - - - - - - - - - - - - - - P17 Screen Mirroring for iOS System (Without WiFi) - - - - - - - - - - - - - - - - - - - - - P17 WiFi Setting Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P17 Using Projector Menu 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P18 Using Projector Menu 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P18 Using Projector Menu 3 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P19 4 Remove & Close The Lens Cover Remove the lens cover before using Close the lens cover when unit is not using LENS COVER REMOVE LENS COVER CLOSE Placing of Your Projector Your projector can be installed in four different configurations (see picture below):
Front Table Rear Table Front Ceiling Rear Ceiling Front Table:
Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability. Rear Table:
Select this location with the projector placed near the floor behind the screen. NOTE: That a special rear projection screen is required. Front Ceiling:
Select this location with the projector suspended upside-down from the ceiling in front of the screen. NOTE: A projector mount is required to install the projector in a ceiling. Rear Ceiling:
Select this location with the projector suspended upside-down from the ceiling behind the screen. NOTE: A projector mount is required to install the projector in a ceiling. A special rear projection screen is required. 5 To reduce Image Distortion Move the projector as close to the center of the screen as possible. The light beam from the projector should be perpendicular to the screen for a rectangular or square image. Distance Between The Projector And Screen Measure the distance between the projector and where you want to position the screen. This is the projection distance. I E Z S N E E R C S DISTANCE Distance 1.16m 1.35m 1.51m 1.79m 2.15m 2.81m 3.43m 4.44m Screen Size 36 inch 45 inch 50 inch 60 inch 72 inch 100 inch 120 inch 150 inch Installing Your Projector in the Ceiling When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount. Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt, please ask the advice from an installation professorial. NOTE: Projector mount and screw(s) not included. CEILING HANGER FIXED HANGER HOLE
(6mm diameter) 6 Adjust The Vertical Location Follow below picture to adjust the vertical location. SCREEN VERTICAL DIMENSION PROJECTOR SCREEN VERTICAL DIMENSION SCREEN VERTICAL DIMENSION PROJECTOR PROJECTOR Adjust this knob ( ANGLE ADJ. knob) to ne- tune the display angle to higher. Adjust The Focus And Keystone Follow below picture to adjust the focus and trapezoidal screen. Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center. Keystone image is created when the projector lens is projected from above or below the center of the screen. Keystone correction restores the distorted image to a rectangular or square shape. KEYSTONE ADJ. KNOB FOCUS ADJ. KNOB Then sharpen the image by rotating focus knob. 7 Controls of Remote Power ON/OFF Skip Next / Previous File Enter to Menu Source Selector Mute Audio Sound Play / Pause Navigator Exit the Menu Decrease Volume Sound Increase Volume Sound Install / Remove Batteries of Remote Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (not included), referring to the polarity markings. Finally, replace the cover. NOTES:
Batteries shall not be exposed to excessive heat such as placing under the sunlight or near a fire. Please make sure the batteries are installed with their correct polarities. Do not mix old and new batteries. Use only the same type of batteries. Do not dispose of the batteries in fire, battery may explode or leak. Do not recharge a non-rechargeable battery. B A T T E R Y D O O R 8 Controls of Projector 1 Front View 3 4 Rear View 2 Top View 5 Right Side V iew 1617 18 19 20 21 6 7 8 9 10 1112 13 14 15 LENS 12 Button ANGEL ADJ. Knob 13 POWER Button VGA IN Port IR Sensor (Rear) SPEAKER 14 POWER Indicator 15 MENU Button 16 TF Card Slot FOCUS ADJ. Knob 17 Audio Out Jack TRAPEZODAL ADJ. Knob 18 AV IN Jack SOURCE Buttonn 19 HDMI 1 & 2 Ports 1 2 3 4 5 6 7 8 9 Vol- Vol+ Button 10 RETURN Button 11 OK Button 20 USB Port 21 DC IN Jack 9 Install Power Adapter Follow below picture to connect power adapter. 1. 2. Plug the AC power cord of small plug side to AC input socket of adaptor. 3. Plug the AC power cord of AC plug side into the 120V AC outlet. Insert the DC plug of the adaptor into the DC IN JACK on the side of the unit. WARNING:
Before connecting to the power supply, ensure that the supply corresponds to the information on the rating label at the back of the apparatus. Main Button Operation
- Press the button to switch on unit, press again to turn off.
/ SOURCE - Press the button to select input source.
/ MENU - Press the button to enter projector menu.
- Press the buttons to navigate and select screen item of menu.
- Press the button to return to previous status or exit the menu.
/ - Press the buttons to select the sound level on the remote. Vol- / Vol+
- Press the buttons to select the sound level on the panel.
- Press to mute the audio. Press again to resume.
- Press the buttons to search next or previous file on USB / TF.
- Press the button to play/pause the playback of file on USB / TF card. 10 Connect HDMI Show The Image On Projector Screen Refer to the following picture to connect a set top box, a BD/DVD player or a streaming player to the HDMI input. 1. Turn off the unit before connect HDMI cable. 2. After connection, press the button to turn on unit and power indicator will light GREEN. In home screen, use buttons to select HDMI 1 or HDMI 2 icon and press the 3. OK button to enter. If not in home screen, press the / SOURCE button to enter. 4. The video from the connected device will be shown on projector screen. 5. Press the button to turn off unit power. CABLE INCLUDED HDMI CABLE Video Player Important Note:
If there is no sound from the internal speakers when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player's digital audio settings and make sure it is set to "PCM Stereo" mode. Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on. Connect AV Show The Image On Projector Screen Follow below picture to connect AV cable and device. 1. Turn off the unit before connect AV cable. 2. Use AV cable to connect follow below figure. 3. After connect, press the button to turn on unit and power indicator will light GREEN 4. In home screen, use buttons to select AV icon and press the button to enter. If not in home screen, press the / SOURCE button to enter. OK 5. The video of AV device will show on projector screen. 6. Press the button to turn off unit power. VIDEO CABLE LEFT CHANNEL RIGHT CHANNEL Video signal cable : Yellow The left channel signal lines: White The right channel signal lines: Red Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on. 11 Connect VGA Show The Image On Projector Screen Follow below picture to connect VGA cable and device. To VGA PORT OR COMPUTER CABLE COMPUTER CABLE NOTE BOOK DECK TOP 1. Turn off the unit before connect VGA cable. 2. Press the button to turn off power of your projector before connection. 3. After connect, press the button to turn on unit and power indicator will light GREEN In home screen, use buttons to select VGA icon and press the button to 4. enter. If not in home screen, press the / SOURCE button to enter. OK 5. The video of VGA device will show on projector screen. 6. Press the button to turn off unit power. Please refer to the following table to adjust the output signal from computer Type Resolution VGA 640x480 PC SVGA 800x600 XGA SXGA 1024x768 1280x1024 Line Frequency
(KHz) 31.5 34.7 37.9 37.5 31.4 35.1 37.9 46.6 48.1 46.9 40.3 48.4 56.5 63.9 79.9 Field Frequency
(Hz) 60 70 72 75 50 56 60 70 72 75 50 60 70 60 75 NOTE: 1. VGA connections do not support audio. You will need to use the laptop or computers connected speakers. 2. If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on. 12 Connect Audio Output (Aux Out/Line Out/Earphones) Follow below picture to connect audio cable and device. 1. Press the button to turn off power of your projector before connection. 2. Use audio cable to connect follow below figure. 3. After connect and turn on both units. Your projector sound from external device now. 4. After using, turn off both unit. AUDIO CABLE Important Note:
If there is no sound from the stereo audio output when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player's digital audio settings and make sure it is set to "PCM Stereo" mode. Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on. Install USB Device And TF (Micro SD) Card Follow below picture to install USB and TF card. Turn off the unit before install USB / TF card. F T TF USB Note: This USB port is only used to read USB flash disk. DO NOT use it to charge any external equipment. 13 Using TF Card And USB Playback (Media Player) Install USB / TF device:
1. Turn off the unit before install USB / TF card. 2. 3. After install, press the button to turn on unit and the power indicator light GREEN. 4. Install the USB device into USB port / Install the TF device into TF slot. In home screen, use buttons to select MOVIE / PHOTO / MUSIC / TEXT icon and press the button to enter. If not in home screen, press the / SOURCE button to enter. If necessary, use the button to select C or D and press button to enter. 5. 6. Use buttons to search the correct file to preview and press the button to OK OK OK playback file. 7. Press button to search next or previous file. 8. During playback, press the button to pause and press again to resume. 9. Press the / EXIT button to exit. NOTE: Before remove USB / TF device, press the button to turn off power FIRST. Sub-Menu on Movie screen 1. When movie playback, press the OK button and more function screen show on lower (figure 1). 2. Use the button to select icon and press the button to play OK special function. Figure 1. PPaauussee FFBB FFFF PPrreevv NN eexxtt SSttoopp RReeppeeaatt AAllll SSeett AA PPllaayylliisstt IInnffoo SSllooww SStteepp GGoottooTTiimmee ZZoooomm IInn ZZoooomm OOuutt AAssppeecctt Sub-Menu on Music screen 1. When music playback, press the OK button and more function screen show on lower (figure 2). 2. Use the button to select icon and press the button to play OK special function. Figure 2. PPaauussee FFBB FFFF PPrreevv NN eexxtt SSttoopp RReeppeeaatt AAllll MM uuttee PP llaayylliisstt IInnffoo GGoottooTTiimmee Sub-Menu on Photo screen 1. When photo playback, press the OK button and more function screen show on lower (figure 3). 2. Use the button to select icon and press the button to play OK special function. Figure 3. PPaauussee PPrreevv NN eexxtt SSttoopp RReeppeeaatt AAllll MM uussiicc OOffff PP llaayylliisstt IInnffoo 90 90 RRoottaattee RRoottaattee ZZoooomm IInn ZZoooomm OOuutt MM oovvee MM uussiicc SS...... Sub-Menu on Text screen 1. When text playback, press the OK button and more function screen show on lower (figure 4). 2. Use the button to select icon and press the button to play OK special function. Figure 4. PPrreevviioouuss...... NN eexxtt PPaaggee PPrreevv NN eexxtt SSttoopp MM uussiicc OOffff PPllaayylliisstt IInnffoo MM uussiicc SS...... Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on. 14 Using Bluetooth Playback Pairing is the term used when two Bluetooth devices are connected wirelessly for the first time. This allows the devices to see each other and sets up a one to one communication channel between both devices. Bluetooth Connection 1. Turn on your External Bluetooth Speaker and select to Bluetooth pairing mode. Note: The effective distance between your external device and projector is within 10 meters (30 feet). 2. Press the button to turn on unit. 3. Press the / MENU button to enter the projector menu screen. 4. Use the button to select Sound menu. 5. Use the button to select BT Setting column as figure 1. 6. Press the button to enter BT Setting menu and use OK buttons to select On. (If BT Setting is On, press the button to enter BT Setting menu.) OK 7. Unit will try to reconnect the previous Bluetooth device, if it is connected before. If not, select Search BT and press button to search device. OK 8. Wait a while, the available Bluetooth speaker device name will show in a list as figure 2. (For example: XXXXXX, YYYYYY, ZZZZZZ and etc.) Sound Mode Standard Treble 50 Bass 50 Balance 0 BT Setting Off Figure 1 BT Setting Off Disconnect / Search BT XXXXXX YYYYYY ZZZZZZ Figure 2 9. Use the buttons to select your desired Bluetooth speaker device and press OK button to connect. (Make sure your Bluetooth headset/audio is connecting) 10. A few seconds, an indicator sound will be heard that your projector and external Bluetooth speaker connected. At the same time, there is C:XXXXXX to indicate the connected device on the BT Setting menu. Then press button to exit. 11. After connection completed, you can listen to music by your Bluetooth receiver device such as a headphone or speaker wirelessly. 12. If you want to change to pair with another Bluetooth Enabled Device, please repeat above step 3 to step 10. Notes:
1) After connecting, Bluetooth devices name will be stored and will automatically connect for next time. 2) Projector Bluetooth (Transmitter) function can only pair with Bluetooth receiver such as headphone or speaker for music streaming wirelessly. Use your Bluetooth device volume control if necessary. Disconnect the Bluetooth 1. Press the / MENU button to enter the menu screen. 2. Use the buttons to select Sound menu. 3. Use the buttons to select BT Setting and press button to enter BT Setting menu. 4. Use the buttons to select Off and press the button to disconnect the Bluetooth OK OK function. Then press button to exit. 15 Multi-screen interactive connection for phone and projector WiFi Connection In home screen, use buttons to select MIRACAST icon and press button to enter. If not in home screen, press the / SOURCE button to enter. 1. 2. In Waiting for connection page, press button to enter WiFi setting menu. In WIFI Setting menu, select WiFi and press button, unit will search available WiFi and show on the screen. OK OK OK 3. Choose the available local WiFi router and input password to 4. connect (using buttons to input password). If unit success to connect the WiFi, it will show the 3 behind the desired local WiFi name on the screen. 5. Press button twice to return Waiting for connection page for iOS/Android screen mirroring. If you want to connect another WiFi, repeat above step #1-3. 6. Note: When the router is successfully connected, the projector will automatically connect to the router next time. Screen Mirroring for Android System (With WiFi) Follow above WIFI Connection section. Then connect your Android mobile device to the same WiFi router. Airplay Function:
1. Play the video on the video app on the mobile, click Projection Screen icon and select PROJECTOR-XXXXXX-DMR on the mobile settings. 2. After connected, the video / movie will be projected on the projector screen. Screen Mirroring:
1. Swipe down from the top of your mobile, click Multi-Screen icon and select PROJECTOR-XXXXXX on the mobile settings. 2. After connected, the mobile device contents will mirror on the projector screen. Screen Mirroring for Android System (Without WiFi) Make sure the projector disconnect to any WiFi. If connected before, press button to enter WIFI Setting menu to select connected WiFi to forget WiFi and return to waiting for connection page. Screen Mirroring:
1. Swipe down from the top of your mobile, Click Multi-Screen and select OK PROJECTOR-XXXXXX on the mobile settings. 2. After connected, the mobile device contents will mirror on the projector screen. Note:
1. Without WiFi connection, only support screen mirroring function. Please connect WiFi if you want to airplay. WiFi connection method please see WiFi connection section on previous page. 2. Different mobile models with different names of screen mirroring function, for examples:
Multi-screen, Wireless Display, Screen Mirroring, Smart View etc 3. XXXXXX is the projector device no. which show on the upper left corner of the Waiting for connection page. 16 Screen Mirroring for iOS System (With WiFi) Follow above WIFI Connection section. Then connect your iOS mobile device to the same WiFi router. Airplay Function:
1. Play the video on the video app on the mobile, click Projection Screen icon and select PROJECTOR-XXXXXX-DMR on the mobile settings. 2. After connected, the video / movie will be projected on the projector screen. Screen Mirroring:
1. Swipe up from the bottom of your mobile, click Screen Mirror icon and select PROJECTOR-XXXXXX on the mobile settings. 2. After connected, the mobile device contents will mirror on the projector screen. Screen Mirroring for iOS System (Without WiFi) Make sure the projector disconnect to any WiFi. If connected before, press button to enter WIFI Setting menu to select connected WiFi to forget WiFi and return to waiting for connection page. Screen Mirroring:
1. Turn on WiFi on your iOS device, click "PROJECTOR-XXXXXX" and input the password OK 12345678 to connect. 2. Swipe up from bottom of your mobile, click Screen Mirror icon and select PROJECTOR-XXXXXX on the mobile settings. 3. After connected, the mobile device contents will mirror on the projector screen. Note:
1. Without WiFi connection, only support screen mirroring function. Please connect WiFi if you want to airplay. WiFi connection method please see WiFi connection section on previous page. 2. XXXXXX is the projector device no. which show on the upper left corner of the Waiting for connection page. iOS Data Cable Screen Mirroring:
Select the MIRACAST function in the main interface, connect your iOS device directly to the projector using the USB cable, click "Trust" in the pop-up box on your phone screen to complete the screen mirroring WiFi Setting Menu In home screen, use buttons to select MIRACAST icon and press button to enter Waiting for connection page. Then press button to enter WIFI Setting menu. OK OK Use UP button or DOWN button to move through and select desired WiFi, Mirror Setting, OTA and Reset. 1. WiFi Select desired local WiFi router to connect. 2. Mirror Setting Select Airplay or Screen Mirroring. 3. OTA Select it for Screen Mirroring software update. 4. Reset Reset the Screen Mirroring and restore all of the default settings. 17 Using Projector Menu 1 Press /MENU button to enter projector menu. Press buttons to select PICTURE menu. Standard Picture Mode Contrast 50 Brightness 50 Color 50 Sharpness 50 Color Temperature Medium Noise Reduction Middle This Picture menu showed on right upper of view screen. USE TO SELECT Picture Mode Standard PRESS OK USE TO SELECT Use to select different picture effect to Standard / Dynamic /
Mild / User. Use to selectand to adjustContrast/
Brightness/ Color / Sharpnessdigit If choseUser item. Contrast 50 PRESS OK USE TO SELECT Use button toadjust Contrast level 0 to 100. (Active in User item of Picture Mode). Brightness 50 PRESS OK USE TO SELECT Use button toadjust Brightness level 0 to 100. (Active in User item of Picture Mode). Color 50 PRESS OK USE USE TO SELECT Sharpness 50 PRESS OK USE USE TO SELECT Color Temperature Medium PRESS OK USE USE TO SELECT Use button toadjust Color level 0 to 100.(Active in User item of Picture Mode). Use button toadjust Sharpness level 0 to 100. (Active in User item of Picture Mode). Use button to select different color temperature to Cool /
Medium / Warm. Noise Reduction Middle PRESS OK Use button to select Off / Low / Middle / High . Using Projector Menu 2 Press /MENU button to enter projector menu, press buttons to select SOUND menu. Sound Mode Standard Treble 50 Bass 50 Balance 0 BT Setting Off USE TO SELECT Sound Mode Standard PRESS OK USE TO SELECT Treble 50 PRESS OK USE TO SELECT Bass 50 PRESS OK PRESS OK USE TO SELECT Balance 0 USE TO SELECT This Sound menu showed on right upper of view screen. Use button to select different sound effect Standard / Movie /
Music / Sports / User. Use to select and to adjust Treble and Bass digit if chose User item. Use button to select Treble level 0 to 100.
(Active in User item of Sound Mode). Use button to select Bass level 0 to 100.
(Active in User item of Sound Mode). PRESS OK PRESS OK Use button to select Balance level to -50 to +50. BT Setting Off PRESS OK PRESS OK Use button to select BT On / Off. 18 Using Projector Menu 3 Press /MENU button to enter projector menu, press buttons to select OPTION menu. e anguag OSD L Flip Aspect Ratio Restore Factory Default Software Update (USB) English Front Table 16 9:
This OPTION menu showed on right upper of view screen. USE TO SELECT OSD Language English PRESS OK Use button to select different language. USE TO SELECT OK OK OK Flip Front Table t PRESS OK USE USE USE TO SELECT TO SELECT TO SELECT Aspect Ratio 16:9 PRESS OK PRESS OK PRESS OK USE USE USE TO SELECT TO SELECT TO SELECT To select different project direction Front Table / Front Ceiling / Rear Table / Rear Ceiling. Use button to select different Aspect Ratio 4:3 / 16:9 / Full Follow below figure. Restore Factory Default t t t PRESS OK PRESS OK PRESS OK USE TO SELECT Use button to select Y or N. If choose Y that your unit will go to factory default setting. Software Update USB
) t PRESS OK For service center use only. Aspect Ratio AV mode HDMI mode VGA mode USB / TF input
(movie mode) 4:3, 16:9, Full, Panorama 4:3, 16:9, Full, Panorama, Just Scan 4:3, 16:9, Full 4:3, 16:9, Full, Panorama, Just Scan DISCLAIMER Unless specifically agreed to in writing, SRIAXNOL:
A. SRIAXNOL makes no warranty as to the accuracy, suffciency or suitability of any technical or other information provided in its manuals or other documentation. B. SRIAXNOL assumes no responsibility or liability for loss or damage, whether direct, indirect, consequential or incidental, which might arise out of the use of such information. The use of any such information will be entirely at the users risk. 19