MODEL NO. : PJ-168 Home Theater Projector with Bluetooth INSTRUCTION MANUAL PLEASE READ BEFORE OPERATING THIS EQUIPMENT ImportantSafetyInstructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. instructions. 7. Do not block any ventilation openings. Install in accordance with the manufacturers 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifier) that product heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Only use attachments/accessories specified by the manufacturer. 11. Unplug this apparatus during lightning storms or when unused for long periods of time. 12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tipover. 1 AdditionalWarningsandPrecautions 1. Do not look directly into the projector light. 2. Donttouchtheprojectlens 3. Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet 4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. 5. WARNING: Changes or modified to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the 6. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. 7. WARNING: Shock hazard - Do Not Open. 8. Caution and marking information is located at the rear or bottom of the completely. equipment. apparatus. 9. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing. 10. Objects filled with liquids, such as vases, shall not be placed on the apparatus. 2 FCCWarning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. InTheBox Remote AC Power Adapter Main Unit HDMI Cable Lens Cover User Manual 3 TableofContents Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - P1 Additional Warnings and Precautions - - - - - - - - - - - - - - - - - - - - - P2 FCC Warning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 In The Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 Table of Contents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P4 Remove & Close The Lens Cover - - - - - - - - - - - - - - - - - - - - - - - - P5 Placing of Your Projector - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P5 To Reduce Image Distortion - - - - - - - - - - - - - - - - - - - - - - - - - - - - P6 Distance Between The Projector And Screen - - - - - - - - - - - - - - - - P6 Installing your Projector in the Ceiling - - - - - - - - - - - - - - - - - - - - P6 Adjust the Vertical Location - - - - - - - - - - - - - - - - - - - - - - - - - - - - P7 Adjust the Focus And Keystone - - - - - - - - - - - - - - - - - - - - - - - P7 Controls of Remote - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P8 Install / Remove Batteries of Remote - - - - - - - - - - - - - - - - - - - - - P8 Controls of Projector - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P9 Install Power Adapter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P10 Main Button Operation - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - P10 Connect HDMI show The Image On Projector Screen - - - - - - - - - P11 Connect AV Show The Image On Projector Screen - - - - - - - - - - - P11 Connect VGA Show The Image On Projector Screen - - - - - - - - - - P12 Connect Audio Output (Aux Out / Line Out / Earphones) - - - - - - - P13 Install USB Device And TF card (Micro SD Card) - - - - - - - - - - - - P13 Using TF Card and USB Playback (Media Player)- - - - - - - - - - - - - P14 Using Bluetooth Playback - - - - - - - - - - - - - - - - - - - - - - - - P15 Multi-screen interactive connection for phone and projector - - - - P16 Using Projector Menu 0 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P18 Using Projector Menu 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P18 Using Projector Menu 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P19 Using Projector Menu 3 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P19 Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P20 4 Remove & Close The Lens Cover RemovethelenscoverbeforeusingClosethelenscoverwhenunitisnotusing PlacingofYourProjector Your projector can be installed in four different configurations (see picture below):
5 Front Table:
Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability. Rear Table:
Select this location with the projector placed near the floor behind the screen. NOTE: That a special rear projection screen is required. Front Ceiling:
Select this location with the projector suspended upside-down from the ceiling in front of the screen. NOTE: A projector mount is required to install the projector in a ceiling. Rear Ceiling:
Select this location with the projector suspended upside-down from the ceiling behind the screen. NOTE:
A projector mount is required to install the projector in a ceiling. A special rear projection screen is required. ToreduceImageDistortion Move the projector as close to the center of the screen as possible. The light beam from the projector should be perpendicular to the screen for a rectangular or square image. DistanceBetweenTheProjectorAndScreen Measure the distance between the projector and where you want to position the screen. This is the projection distance. Distance 1.16m 1.35m 1.51m 1.79m 2.15m 2.81m 3.43m 4.44m Screen Size 36inch 45inch 50inch 60inch 72inch 100inch 120inch 150inch InstallingyourProjectorintheCeiling When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount. Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt, please ask the advice from an installation professorial. NOTE: Projector mount and screw(s) not included 6 AdjustTheVerticalLocation Follow below picture to adjust the vertical location. AdjustTheFocusAndKeystone Follow below picture to adjust the focus and trapezoidal screen. Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center. or square shape. Keystone image is created when the projector lens is projected from above or below the center of the screen. Keystone correction restores the distorted image to a rectangular 7 ControlsofRemote Install/RemoveBatteriesofRemote Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (included), referring to the polarity markings. Finally, replace the cover. NOTES:
Batteries shall not be exposed to excessive heat such as placing under the sunlight or near a fire. Please make sure the batteries are installed with their correct polarities. Do not mix old and new batteries. Use only the same type of batteries. Do not dispose of the batteries in fire, battery may explode or leak. Do not recharge a non-rechargeable battery. 8 ControlsofProjector 1 2 3 4 5 6 7 8 9 LENS IR Sensor (Front) ANGEL ADJ. Knob VGA IN Port 12 13 Button Buttons 14 RETURN Button 15 POWER Button IR Sensor (Rear) 16 POWER Indicator SPEAKER 17 TF Card Slot FOCUS ADJ. Knob 18 Audio Out Jack TRAPEZOIDAL ADJ. Knob 19 AV IN Jack SOURCE Button MENU Button Vol- Vol+ Buttons 10 11 20 HDMI 1 & 2 Ports 21 22 USB Port DC IN Jack 9 InstallPowerAdapter Follow below picture to connect power adapter Connect small end of adapter FIRST. Plug the adapter body to power outlet. WARNING:
Before connecting to the power supply, ensure that the supply corresponds to the information on the rating label at the back of the apparatus. MainButtonOperation
- Press the button to switch on unit, press again to turn off.
/ SOURCE - Press the button to select input source.
/ MENU - Press the button to enter projector menu.
- Press the buttons to navigate and select screen item of menu.
- Press the button to return to previous status or exit the menu.
- Press the buttons to select the sound level on the remote. Vol- / Vol+ - Press and hold the buttons to turn the volume up/down on the pannel.
- Press to mute the audio. Press again to resume. 10 ConnectHDMIShowTheImageOnProjectorScreen Refer to the following picture to connect a set top box, a BD/DVD player or a streaming player to the HDMI input. 1. Press the 2. After connection, press the button to standby mode before connect HDMI cable. button to turn on unit and power indicator will light GREEN 3. Press the
/ SOURCE button to home screen, use buttons to select HDMI 1 or HDMI 2 icon and press the from the connected device will be shown on projector screen. button to enter HDMI mode. The video button to turn unit to standby. 4. Press the GREEN 5. Press the 11 Important Note:
If there is no sound from the internal speakers when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player's digital audio settings and make sure it is set to "PCM Stereo" mode. ConnectAVShowTheImageOnProjectorScreen Follow below picture to connect AV cable and device. 1. Press the button to standby mode before connect AV cable. 2. Use AV cable to connect follow below figure 3. After connect, press the button to turn on unit and power indicator will light 4. Press the
/ SOURCE button to home screen, use AV mode and the video of AV device will show on projector screen. buttons to select button to turn the unit to standby. ConnectVGAShowTheImageOnProjectorScreen Follow below picture to connect VGA cable and device. 1. Press the button to standby mode before connect VGA cable. 2. After connect, press the button to turn on unit and power indicator will light GREEN. 3. In home screen, use to enter VGA mode. The video of VGA device will show on projector screen buttons to select VGA icon and press the button 4. Press the button to turn the unit to standby. Pleaserefertothefollowingtabletoadjusttheoutputsignalfromcomputer Type Resolution VGA 640x480 PC SVGA 800x600 XGA 1024x768 NOTE: VGA connections do not support audio. You will need to use the laptop or computers connected speakers Field Frequency 60 70 72 75 50 56 60 70 72 75 50 60 70 Frequency 31.5 34.7 37.9 37.5 31.4 35.1 37.9 46.6 48.1 46.9 40.3 48.4 56.5 12 ConnectAudioOutput(AuxOut/LineOut/Earphones) Follow below picture to connect audio cable and device. 1. Press the button to standby of your projector before connection. 2. Use audio cable to connect follow below figure. 3. After connect and turn on both units. Your projector sound from external device now. 4. After using , turn off both unit Important Note:
If there is no sound from the stereo audio output when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player's digital audio settings and make sure it is set to "PCM Stereo" mode. InstallUSBDeviceAndTFcard(MicroSDCard) Follow below picture to install USB and TF card Turn off the unit before install USB / TF card. 13 UsingTFCardAndUSBPlayback(MediaPlayer) Install USB / TF device:
1. Press the 2. 3. After install, press the button to standby before install USB / TF card. Install the USB device into USB port / Install the TF device into TF slot. button to turn on unit and the power indicator light GREEN. 4. In home screen, use buttons to select PHOTO / MUSIC / MOVIE / TEXT icon and press the button to enter. 5. Use the button to select C and press button to enter. 6. Use buttons to search the correct file to preview and press the button to playback file. NOTE: Remove USB / TF device, press the 1. When movie playback, press Figure 1. Sub-Menu on Movie screen button to turn off power FIRST. Sub-Menu on Photo screen Figure 2. Sub-Menu on Music screen Figure 3. button and more function the screen show on lower (figure 1). 2. Use the button to select icon and press the play special function. button to 1. When photo playback, press the button and more function screen show on lower
(figure 2). 2. Use the button to select icon and press the play special function. button to 1. When music playback, press the button and more function screen show on lower
(figure 3). 2. Use the button to select icon and press the play special function. button to button and more function screen show on lower (figure 4). 2. Use the button to select icon and press the play special function. button to 14 1. When text playback, press the Figure 4. Sub-Menu on Text screen UsingBluetoothPlayback Pairing is the term used when two Bluetooth devices are connected wirelessly for the first time. This allows the devices to see each other and sets up a one to one communication channel between both devices. Bluetooth Connection 1. Press the button to turn on unit and power indicator will light GREEN. 2. Press the
/MENU button to enter the projector menu. 3. Press buttons to select SOUND menu as Figure. 4. Use the button to select BT Setting column. 5. Press the buttons to select BT Setting On 6. Turn on your External Bluetooth Speaker and select to Bluetooth pairing mode 7. A few seconds, next the BT logo will show the connected External Bluetooth Speaker name in the main function page. 8. After connection completed, the unit sound to External Bluetooth speaker. Disconnect the Bluetooth 1. Press the
/MENU button to enter the projector menu 2. Press buttons to select SOUND menu as Figure. 3. Use the button to select BT Setting column. 4. Press the buttons to select BT Setting Off. The Bluetooth will disconnect. 15 Multiscreeninteractiveconnectionforphoneandprojector Wireless Projection First, ensure the projector and the mobile is connected to the same wireless network. Following below steps. Connect local WiFi router 1. Press the button to turn on unit and power indicator will light GREEN. 2. Press the
/ SOURCE button to select Miracast icon and press button to enter Miracast / Airplay page on the screen. 3. Click the WiFi menu to search and select Display_XXXX (XXXX is numbers and letters which show on the Miracast / Airplay page on the screen) and enter password 12345678 to connect on your mobile device. 4. After connect, scan QR code or click the browser, input IP 192.168.XX.XXX
(XX.XXX is numbers which show on the Miracast / Airplay page on the screen) on the mobile. The Screen Mirroring Device Management menu will show on your mobile to configure screen mirroring parameters, choose local WiFi router and enter 5. After connected, local WiFi router name and icon will show on the Miracast / Airplay password to connect. page on the screen. 6. If you want to connect another local WiFi router, repeat step 4 to choose another one. Note: When the router is successfully connected, the projector will automatically Android Mirroring Function (Miracast mode) (no need to connect the WiFi router) Miracast / Airplay page. 1. Press the
/ SOURCE button to select Miracast icon and press button to enter 2. Turn on WiFi function on your mobile device (no need to connect any WiFi router) 3. Click Miracast function (different mobile models with different names for example:
Multi-screen, Wireless Display, Screen Mirroring, Smart View etc) and select Display_XXXX-Mira(XXXX is numbers and letters which show on the Miracast /
Airplay page on the screen) on the mobile settings 4. After connected, the mobile device contents will mirror on the projector screen Android Mirroring Function (DLNA mode) (unit need to connect the WiFi 1. Press the
/ SOURCE button to select Miracast icon and press button to enter 2. Connect the same WiFi network as previous Connect local WiFi router section router) Miracast / Airplay page. for projector and mobile. 3. Open the App and select the video / movie to play on your mobile 4. Click Projection Screen and select Display_XXXX (XXXX is numbers and letters which show on Miracast / Airplay page) on the mobile settings. 5. After connected, the mobile device contents will project on the projector screen. 16 iOS mobile Screen Mirroring Function (no need to connect the WiFi router) 1. Press the
/ SOURCE button to select Miracast icon and press button to enter Miracast / Airplay page 2. Click the Wi-Fi menu to search, select Display_XXXX (XXXX is numbers and letters which show on the Miracast / Airplay page on the screen) on the mobile device and enter Pin 12345678 to connect 3. Click Screen Mirroring function and select Display_XXXX (XXXX is numbers and letters which show on the Miracast / Airplay page on the screen) on the mobile device to connect 4. After connected, the mobile device contents will mirror on the projector screen iOS mobile Airplay Function (unit need to connect the WiFi router) 1. Press the
/ SOURCE button to select Miracast icon and press button to enter 2. Connect the same WiFi network as previous Connect local WiFi router section 3. There are two modes for using (a) Screen Mirroring mode or (b) Airplay mode Miracast / Airplay page. for projector and mobile.
(a) Screen Mirroring mode:
1. Click Screen Mirroring function and select Display_XXXX (XXXX is numbers and letters which show on the Miracast / Airplay page on the screen) on the mobile device to connect
(b) Airplay mode:
2. After connected, the mobile device contents will mirror on the projector screens 1. Open the App and select the video / movie to play on your mobile 2. Click Projection Screen and select Display_XXXX (XXXX is numbers and letters which show on the Miracast / Airplay page on the screen) on the mobile settings. 3. After connected, the mobile device contents will project on the projector screen. Wired Projection iOS mobile Follow below picture to connect projector to mobile with the data cable. 1. Press the button to standby mode before connect data cable (not included). 2. After connect, press the button to turn on unit and power indicator will light GREEN 3. In home screen, use buttons to select MIRACAST icon and press the button to enter Miracast / Airplay page. 4. Select trust on the popup window of your mobile. The video of mobile device will show on projector screen 5. Press the button to turn the unit to standby. Note: Wired Projection function supports iOS mobile device only. 17 UsingProjectorMenu0 Press
/MENU button to enter projector menu. UsingProjectorMenu1 Press
/MENU button to enter projector menu. Use Use Use Use This Screen menu showed on right upper of view screen.
(Active in VGA mode) buttons to adjust Horizontal Pos. level -16 to 16. buttons to adjust Vertical Pos. level -16 to 16. buttons to adjust Clock digit -30 to 30. buttons to adjust Phase digit 0 to 31. This Picture menu showed on right upper of view screen. to select and buttons to adjust Contrast level 0 to 100. buttons to adjust Brightness level 0 to 100. to select different picture effect to Standard /
to Use Dynamic / Mild / User. Use adjust Contrast / Brightness / Color / Sharpness digit If chose User item. Use
(Active in User item of Picture Mode). Use
(Active in User item of Picture Mode). Use
(Active in User item of Picture Mode). Use
(Active in User item of Picture Mode). Use Cool / Medium / Warm. Use buttons to adjust Sharpness level 0 to 100. buttons to adjust Color level 0 to 100. buttons to select Off / Low / Middle / High buttons to select different color temperature to 18 UsingProjectorMenu2 Press menu.
/MENU button to enter projector menu, press buttons to select SOUND UsingProjectorMenu3 Press menu.
/MENU button to enter projector menu, press buttons to select OPTION to select different sound effect Standard / Movie /
to select and This sound menu showed on right upper of view screen. Use Music / Sports / User. Use adjust Treble and Bass digit if chose User item. Use
(Active in User item of Sound Mode). Use
(Active in User item of Sound Mode). Use Use buttons to select Balance level to -50 to +50. buttons to select Treble level 0 to 100. buttons to select Bass level 0 to 100. buttons to select On /Off to This OPTION menu showed on right upper of viewing screen. Use Use Table / Rear Ceiling Use to select different Aspect Ratio 4:3 / 16:9 / Full /
Zoom1 / Zoom2 / Panorama / Just Scan. (Active by Movie) Use unit will go to factory default setting. buttons to select Y or N. If choose Y that your button to select different language. button to select Front Table / Front Ceiling / Rear For service center use only 19 Specifications Bluetooth Version 5.1 (Transmitter) Light Source Type LED Display Native Resolution 1280 x 720 RGB HDMI Input Supported 1080p , 1080i , 720p, 576i , 480p, and 480i Video Resolution. Power Consumption 80W Included Adapter Input AC100-240V,50/60Hz Connect DC input of unit Output DC26V, 2.7A. Projection Size 36-150 inch Input Port USB Port AV/ VGA / HDMI Support USB device up to 32GB Support format Mpeg1, Mpeg2, Mpeg4, mp3, Jpeg TF Card Support TF card up to 32GB Support format Mpeg1, Mpeg2, Mpeg4, mp3, Jpeg Net Weight (unit) 1.5 KG Product Dimensions 260 x 211 x 98 mm Specifications are typical, individual units might vary. They are subject to continuous improvement without notice and without incurring any obligation. 20