FCC ID: 2APR4-M2 Wi-Fi ROUTER

FCC ID:2APR4-M2 This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of conditions:

the device. The distance between user and products should be no less than 20cm Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes :

( 1 ) Ce dispositif ne peut causer d'interfrences ; et

( 2 ) Ce dispositif doit accepter toute interfrence , y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. la distance entre l'utilisateur et les produits devraient tre au moins 20 cm This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

FCC ID: XXXXXX This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. The distance between user and products should be no less than 20cm Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes :

( 1 ) Ce dispositif ne peut causer d'interfrences ; et

( 2 ) Ce dispositif doit accepter toute interfrence , y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. la distance entre l'utilisateur et les produits devraient tre au moins 20 cm This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

WiFi 2.4g/5G antenna 2 WiFi 2.4g/5G antenna 1 2.4g/5G

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R18042804-1E1 12. Photos of the EUT M2:

Page 84 of 99 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R18042804-1E1 Page 85 of 99 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R18042804-1E1 Page 86 of 99 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R18042804-1E1 Page 87 of 99 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R18042804-1E1 Page 88 of 99 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R18042804-1E1 M2A:

Page 94 of 99 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R18042804-1E1 Page 95 of 99

Mercku Inc. DATE : 2019-9-17 MiCOM Labs, Inc 575 Boulder Court, Pleasanton California 94566, USA Attn: Director of Certification FCC ID: 2APR4-M2 Authority to Act as Agent On our behalf, | appoint below company and person:

Dongguan Dongdian Testing Service Co.,Ltd. 17, Zongbu Road 2, Songshan Lake Sci&Tech, Industry Park, Dongguan City, Guangdong Province, China, 523808 Tel / Fax Tel: +86-0769-89201699 fax:+86-0769-22895596 E-Mail leolilu@dgddt.com to act as our agent in the preparation of this application for equipment certification. |

certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission's regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by MiCOM Labs, Inc, still resides with:

Applicantname |Merckulnc, ag Address 51 Breithaupt Street, Suite 100 Kifhener, ON Canada, N2H 5G5 Yours sincerely, \

Signatory \ /

(Name | ShiGe 51 Breithaupt Street, Suite 100 Kitchener, ON Canada, N2H 5G5

Mercku Inc. September 19, 2019 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: 2APR4-M2 Applicant: Mercku Inc. Dear Examiner, This is to request a Class II Permissive change for FCC ID: 2APR4-M2 originally granted on 06/28/2018 (date). The change under this application as following:

There are no RF parameter changes to the operating frequency band, rated radiated and conducted output power of the device, only Add a Adapter and Manufacturer <<

M2 change instruction.pdf>>. I attest that the certified device will not be capable of ad-hoc mode operation outside of the grant conditions. Sincerely, FCC_Class II PC request letter Rev1.0

< Mercku Inc. >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Subject; Request for Long Term Confidentiality FCC ID: 2APR4-M2 To Whom It May Concern, Date: 2019-9-17 Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Tune-up Procedure software security description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality ofthe following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuanttoKDB 726920 D01.

Mercku Inc. DATE : 2018-6-4 MiCOM Labs, Inc 575 Boulder Court, Pleasanton California 94566, USA Attn: Director of Certification FCC ID: 2APR4-M2 Authority to Act as Agent On our behalf, I appoint below company and person:

Name Position Company Name Dongguan Dongdian Testing Service Co.,Ltd. Address Leo Liu Manager 17, Zongbu Road 2, Songshan Lake Sci&Tech, Industry Park, Dongguan City, Guangdong Province, China, 523808 Tel: +86-0769-89201699 fax:+86-0769-22895596 leoliu@dgddt.com Tel / Fax E-Mail to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by MiCOM Labs, Inc, still resides with:

Applicant name Mercku Inc. Address Yours sincerely, 509 Beaver Creek Rd. Waterloo, Ontario, Canada Signatory Shi Ge Name Position Co-founder Company Name Mercku Inc. Address 509 Beaver Creek Rd. Waterloo, Ontario, Canada

Mercku Inc. Declaration of difference Date: 2018-6-14 To Whom It May Concern:

The product: Wi-Fi ROUTER, Model No.: M2, M2A, all models have the same Antenna shape, circuit diagram and RF module, but only difference on appearance. Yours sincerely, Signatory Name Position Shi Ge Co-founder Company Name Mercku Inc. 509 Beaver Creek Rd. Waterloo, Ontario, Canada

+86 15210895289 ge.shi@mercku.tech Address Tel / Fax E-Mail

Mercku Inc. Letter of Authorization Company: Mercku Inc. Address:

509 Beaver Creek Rd. Waterloo, Ontario, Canada Product Name: Wi-Fi ROUTER Model Number: M2/ M2A FCC Identifier:

2APR4-M2 We authorize MiCOM LabsInc, 575 Boulder Court, Pleasanton, California94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM LabsInc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Shi Ge Title: Co-founder Signatureof applicant:

Date: 2018-6-5

Mercku Inc. FCC Software Configuration Control Declaration Date: 2018-6-4 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Product/ Model Number: Wi-Fi ROUTER/ M2/ M2A Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Shi Ge Title: Co-founder Signature of applicant Date: 2018-6-4 FCC Software Configuration Control Declaration Rev1.0.docx

< Mercku Inc. >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Subject; Request for Long Term Confidentiality FCC ID: 2APR4-M2 To Whom It May Concern, Date: 2018-6-4 Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Tune-up Procedure software security description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality ofthe following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuanttoKDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Shi Ge Title: Co-founder