Wireless Vehicle Detector User Manual Release Date 2016.03 Version 1.0 Author Jiangshuai Ding Liu Shihe NO.40,Beiyuan Road,Chaoyang District,Beijing,P.R.C Tel+86(10)-88998881 1. Application Traffic data collection Vhicle flow detection, Vehicle speed detection, Traffic occupancy, Analysis of Vehicle Type 2. Product Description The Wireless Vehicle Detector is a low power ZigBee device. It uses highly sensitive sensors detect a vehicle status information through a magnetic field around the device relative changes in Earth's magnetic field to analyze ON-OFF status of the vehicle, and this data is based on low-power wireless protocol transmitted to receivers and repeaters.Device has 16 working channels. According to environmental noise, we can open the application software switching equipment working channel. Easy installation, convenient, without prejudice to the roadbed .It uses 3.6V Li / SOCl2 battery, and work more than five years.Key Features See Table 1. 2.4GHz Radio Frequency Band Transmission Rate 250kbps Number Of Channels 16 Antenna Beamwidth 60 Channel Bandwidth 5MHz Key Features Max Output Power 0dBm Receiver Sensitivity -95dBm Protection Class Operating Temperature Relative Humidity IP68
-4085 95%(Non Condensing) 5 years Detection Sensitivity Antenna Type Power 0-15 Level Operating Life Ceramic Antenna Li/SOCI2 Battery 3.6V,18Ah Laying Methods Use special sealed plastic magnetic sealing, after hardening the surface of the device below ground 2CM Table 1. 3. Wireless Vehicle Detector Installation Guide Preparations: The Wireless vehicle detector is a device buried below ground level.Before embedded in the road surface, we use a water_drilling device to dig a depth of 110mm, and108mm diameter circular aperture.(See Figure 1.) Installation Requirements: Arrow atop the of The Wireless vehicle detector indicate the direction of travel. Mark and record device ID number in the corresponding position of the lane on the drawings.After,use special glue to fill the hole until it dried. NO.40,Beiyuan Road,Chaoyang District,Beijing,P.R.C Tel+86(10)-88998881 Structure Max Size:94mm*66mm Figure 1. Notice: Reverse installation location (Detector to the parking line for the front, the opposite direction for the rear) must have a pole (Street lamp pole, Signal lamp pole or Control rod). It is to prepare for the installation of repeater later. NO.40,Beiyuan Road,Chaoyang District,Beijing,P.R.C Tel+86(10)-88998881 4.MeritPlusDta Technical Support Internet: http://www.meritplusdata.com/
WeChat Public Number:
Technical Support NO.40,Beiyuan Road,Chaoyang District,Beijing,P.R.C Phone:+86(10)-8899-8881/3-201 FAX Email: support@Meritplusdata.com
: +86(10)-88998882-204
: +86(10)-88998882-204 Marketing Support NO.40,Beiyuan Road,Chaoyang District,Beijing,P.R.C Phone:+86(10)-8899-8881/3-102 FAX Email: sales@Meritplusdata.com This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a NO.40,Beiyuan Road,Chaoyang District,Beijing,P.R.C Tel+86(10)-88998881 particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. NO.40,Beiyuan Road,Chaoyang District,Beijing,P.R.C Tel+86(10)-88998881