FCC ID: P3O97802 Telematic Tracking System

0 0 8 3 7 2 0 4 0 5 SAT RC 09 INSTALLATION MANUAL EN CAUTION

- Only carry out the operations described in this manual.

- The installer is not authorized to remove the warranty seals or to access the interior parts of the products or accessories.

- The installer is not authorized to modify and/or adapt the product or the relative accessories.

- The manufacturer declines all liability for damage to persons and/or property caused by incorrect installation of the product. DISCONNECT THE VEHICLES BATTERY TECHNICAL SPECIFICATIONS Dimensions and weight:....................................................................................104X75X27, 168g Power supply voltage:................................................................................................12 VDC Temperature:..........................................................................................................-25+70C Power input*:.............................................................................................................<2mA

*With the peripheral device connected, the GPS off, Sat Programmer disconnected and the internal buffer battery charged. Maximum current:.............................................................................................................<210mA GENERAL LAYOUT MAROON DARK BLUE GPS ANTENNA GSM ANTENNA

+15

+12 GND 5A

*

IGNITION KEY POSITIVE

(+15) BATTERY POSITIVE

(+12V) GROUND

* : MANDATORY Fig.1 PRESS TO RELEASE Release and position the lever as shown in the figure before connecting the 18-pin loose connector to the terminal. PHASE 3 Lock the connector to the terminal by positioning the lever as shown in the figure. WARNING: make sure that the connector is inserted and locked to the terminal in the correct way. Fig.4 See pic. 5 SAT PROGRAMMER CONNECTOR CONNECTIONS PHASE 1 Fig.2 PHASE 2 Connect the connectors to the terminal Fig.3 CONNECTION CRASH SENSOR CAUTION!

CHECK THE CORRECT CONNECTION CLICK!

CLICK!

HOW TO POSITION THE DEVICE Position the device in a concealed part of the vehicle, inside the passenger compartment To allow the diagnosis and testing operations to be carried out without difficulty, it is essential to install the device in a position where it can be easily reached with the cable of the Sat programmer. Do not install the device under a mat, where it could be trodden on or crushed by a load. It is advisable to lock the device to a rigid part of the vehicle. HOW TO POSITION THE CRASH SENSOR FIXING WITH SPACER Fig.5 Fig.6 Y TOP OF VEHICLE LEFT SIDE OF VEHICLE X Fix the sensor temporarily in place with the screw. Check the position of the sensor by means of the relative Sat Programmer menu. Fix the sensor permanently in place. P O T F R O N T FRONT OF VEHICLE RIGHT SIDE OF VEHICLE Y 0 X HOW TO CONNECT THE GSM ANTENNA Use the supplied spacer to install the sensor on a flat surface, opposite the fastening tabs (e.g. longitudinal frame members on the PASSENGERS SIDE, surfaces BELOW the sensor). The sensor must NOT be turned. Comply with the position indicated on the sticker affixed to the side of the sensor. HOW TO INSERT THE SPACER FIXING IN THE VEHICLE FRONT OF VEHICLE Y TOP OF VEHICLE RIGHT SIDE OF VEHICLE LEFT SIDE OF VEHICLE X X Fig. 7

!

Pay particular attention to the direction in which the spacer is inserted. Fig. 8 Fig. 9 GSM ANTENNA THE ANTENNA IS RESIN-

COATED AND CAN THEREFORE BE INSTALLED ON THE OUTSIDE OF THE VEHICLE (E.G. UNDER THE MUDGUARDS, IN A HEADLIGHT......) OK OK OK OK IT MUST NOT BE VISIBLE OR EASILY ACCESSIBLE FROM THE OUTSIDE DO NOT COVER WITH PARTS OR METALLIC PAINTS CAREFULLY CLEAN THE FIXING SURFACE ONCE YOU HAVE CHOSEN THE POSITION FOR THE ANTENNA, MAKE SURE THAT THE RECEPTION IS GOOD BEFORE FIXING IT IN PLACE:

- CONNECT THE SAT PROGRAMMER AND TEST TO MAKE SURE THAT EVERYTHING WORKS PROPERLY BY MEANS OF THE APPROPRIATE FUNCTION (CONSULT THE RELATIVE MANUAL). Fig. 10 HOW TO CONNECT THE GPS ANTENNA OK OK OK IT MUST NOT BE VISIBLE OR EASILY ACCESSIBLE FROM THE OUTSIDE DO NOT COVER WITH PARTS OR METALLIC PAINTS HOW TO FIX THE ANTENNA:

- ON METAL PARTS WITHOUT THE USE OF THE DOUBLE-SIDED ADHESIVE MATERIAL (THE ANTENNA IS MAGNETIC)

- ON PLASTIC PARTS USING THE DOUBLE-SIDED ADHESIVE MATERIAL SUPPLIED IN THE KIT OK THE ANTENNA IS RESIN-

COATED AND CAN THEREFORE BE INSTALLED ON THE OUTSIDE OF THE VEHICLE

(E.G. UNDER THE MUDGUARDS, IN A HEADLIGHT......) Fig. 11 GPS ANTENNA ONCE YOU HAVE CHOSEN THE POSITION FOR THE ANTENNA, MAKE SURE THAT THE RECEPTION IS GOOD BEFORE FIXING IT IN PLACE:

- DRIVE THE VEHICLE TO AN OPEN SPACE, WELL AWAY FROM BUILDINGS OF A CERTAIN HEIGHT

- CONNECT THE SAT PROGRAMMER AND TEST TO MAKE SURE THAT EVERYTHING WORKS PROPERLY BY MEANS OF THE APPROPRIATE FUNCTION (CONSULT THE RELATIVE MANUAL). 90 NO OK KO CAREFULLY CLEAN THE FIXING SURFACE OK Meta System S.p.A. Model: SAT RC 09 FCC ID.: P3O97802 This device complies with Part 15 of the FCC rules subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept all interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. R&TTE Declaration Of Conformity (DoC) 0470 We: Meta System S.p.A. with the address:

Via Majakovskij 10 b/c/d/e 42124 Reggio Emilia Italy Declare Under own responsibility that the product:

SAT RC 09 To which this declaration relates is in conformity with the essential requirements and other relevant requirements of the R&TTE Directive

(1999/5/EC). This product is in conformity with the following standards

- Health & Safety (art.3.1) EN 60950-1

- EMC (art.3.2)

- Spectrum

- Human exposure ETSI EN 301 489-1/-7/-19 ETSI EN 301 511 EN62311 According to Directive 1999/5/CE Cesare Reggio Emilia , 15/03/2010 Technical Director Lasagni

COMPANY WITH QUALITY SYSTEM CERTIFIED BY DNV

= 150 9001:2000 ISO/TS16949 =

200106 DATE 5th MAY 20010 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act.as Agent On our behalf, | appoint Nemko Spa via del Carroccio n. 4, Biassono (MB) Italy to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission's regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with (applicant name and address). Dated 5 Day of May 20 10 this Agency agreement expiration date: May 2017 By: Maldini Giorgio SYSTEM: , 4219 Funilia Signature 3 Title: Homologation Manager On behalf of : Meta System S.p.A. Telephone: +39 0522 364256 Meta System S.p.A. - Cap. Soc. 9.263.898,00 i.v. - N Reg. Impr. ~ Partita .V.A. e Codice Fiscale 00271730350 N R.E.A. 120639 Sede Legale Head Office: Via Majakovskij, 10/b/c/d/e 42100 REGGIO EMILIA (ITALY) - Telefax +39 0522 308382 - Tel. +39 0522 364114 info@metasystem.it - Soggetta a direzione e coordinamento di MetaSystem Group S.p.A. - Web: www.metasystem.it

Operational Description for Telematic Tracking System called SAT RC 09 The product is a vehicle tracking system use to follow the vehicle and to allow the recovery of the vehicle in case of stolen, theft or after crash. the product is fitted on the vehicle by means a 3 wires connection, to simplify the installation on all the vehicle range. The harness is provided with all the wires black, to know the wire to be use a number is placed on the part that will be sliced before connection. The product contains a Jasper SIM card to manage only M2M service, to manage the data transmitted the SOC ( Security Operational Center) is needed. The system is used to count the mileage of the vehicle the system contains a GPS localizing system to know the positions and to send this information, periodically, to the operating centre. Information are related to time, positioning and this information are matched with the area to know road type, highway, urban ecc.th scope is to provide insurance service at the user. The PCB is build around a single motherboard, two layers of components, that contains the functions to manage, tracking, communications, tilt sensor. The communication with the operating centre, to collect data, is based on GPRS communication . The internal modem is a TELIT GE864 Quad Band module the system is managed from an internal microcontroller M32C87A. from Renesas, that manage all the I/O, tilt sensor, and the user interface as well. The frequencies of the main clock is 10 MHz, an additional quartz for with EEPROM external memory of 256 bytes. The microprocessor is equipped with hardware and software watchdog;

The product is for vehicle application, the power supply is the 12 Volt DC provided from the main battery. The product contains an internal battery backup pack, 7,2 V NiCd, to allow the functionality of the system to avoid manipulation or frauds. The products is provide with 2 antennas, one for the GPS receiver and one for the GPRS bi-directional communication. The GPRS antenna gains is from 0~0.5 dBi @ 880 960 MHz from 0.5 ~ 1 dBi @ 1710 1990 MHz. The system is installed in the vehicle by the dealer or by the authorized centre and it is completely invisible at the end user. No operating manual is provided because the user do not use the product but the system is use for the vehicle tracking. The product is provided only with the installation instruction. Safety and reliability The following points outline the safety and reliability factors which have been considered in the design of the units. Reverse polarity protection of the unit Load dump protection All the connections, except antennas, are on AMP MQS 18 poles connector;

Built-in Hardware watch-dog for microprocessor to prevent any lock-up PCB with large ground plate to get better rejection to electromagnetic disturbance INPUT Permanent 12 V power supply (+30) Ignition (+15) Power negative supply (-31) GPRS antenna and GPS antenna are connected with Fkra connectors with secondary lock.

SAT RC 09 TELIT ANTENNA STAMPATO - Revised: marted, ottobre 20, 2009 3020097802 Revision: 0 3020097802_C36 METASYSTEM S.P.A. PROPERTY ALL RIGHTS RESERVED ART.1151-1/2/3 IL TECNICO PROGETTISTA: R.ROMAGNOLI IL TECNICO DISEGNATORE: R. ROMAGNOLI DVP-S 159 REV.000 21/10/02 Bill Of Materials Oct 20,2009 14.23.43 Page: 1 Quantity Item ____________________________________________________________________________________ ____ Reference Part

------ Componenti SMD ------------------------------------------------------

1 12 'C90,R28,R29,R30,R31, 1550003900,0,SMD,0402,,1/16W,5%

R32,R33,R34,R35,R36,R37 R38 2 2 'L10,'L11 1550000900,0,SMD,0603,,1/10W 3 2 C1,C2 1500034300,100U,SMD,C-SIZE-C,6V3 4 2 C3,C4 1500028600,2U2,SMD,0805_C_DX,10V,,10%,,,X7R,AUTOM 5 2 C5,C6 1500024500,100N,SMD,0603,50V,,10%,,,X7R,AUTOM 6 2 C7,C8 1500013500,330P,SMD,0402,50V,,,,,C0G 7 1 C9 1500015400,1N,SMD,0402,50V,,10%,,,X7R 8 2 C10,C11 1500028700,2U2,SMD,0805_C_DX,25V,,10%,,,X7R 9 1 C12 1500034800,220U,SMD,CESMD6X6X5.5,16V,,20%,,,-55/+105C 10 9 C13,C14,C15,C16,C17,C18, 1500009000,33P,SMD,0402,50V,,,,,C0G C19,C20,C21 11 1 C22 1500034100,100U,SMD,CESMD6X6X8,35V 12 1 C23 1500003700,1P8,SMD,0402,50V,,+/-0.25PF,,,C0G 13 22 C24,C25,C26,C27,C28,C29, 1500022700,100N,SMD,0402,16V,,,,,X7R C30,C31,C32,C33,C34,C35 C36,C37,C38,C39,C40,C41 C42,C43,C44,C45 14 1 C46 1500009800,47P,SMD,0402,50V,,10%,,,C0G 15 3 C47,C48,C49 1500007900,18P,SMD,0402,50V,,5%,,,C0G 16 20 C50,C51,C52,C53,C54,C55, 1500026900,1U,SMD,0402,10V,,10%,,,X5R C56,C57,C58,C59,C60,C61 C62,C63,C64,C65,C66,C67 C68,C69 17 2 C70,C71 1500027900,1U,SMD,0603,25V,,10%,,,X5R,AUTOM 18 1 C72 1500034600,150U,SMD,C-SIZE-D,6V3 19 7 C73,C74,C75,C76,C77,C78, 1500019400,10N,SMD,0402,25V,,,,,X7R C79 20 5 C80,C81,C82,C83,C84 1500028900,4U7,SMD,0805_C_DX,16V,,10%,,,X5R,AUTOM 21 1 C85 1500006900,8P2,SMD,0402,50V,,,,,C0G 22 34 C86,C87,C88,C89,C90,C91, 1500011100,100P,SMD,0402,50V,,5%,,,C0G C92,C93,C94,C95,C96,C97 C98,C99,C100,C101,C102 C103,C104,C105,C106 C107,C108,C109,C110 C111,C112,C113,C114 C115,C116,C119,C120,C121 Page 1 3020097802_C36 23 2 C117,C118 1500026300,470N,SMD,0402,6V3,,10%,,,X5R 24 1 D1 1520005800,BAV99,SMD,SOT23_DX,70V,,,200MA,,150C 25 1 D2 1520008100,BAV99W,SMD,SOT-323_DX,,,,,,-65/+150C 26 1 D3 1520010400,SCHOTTKY 40V-2A,SMD,SMD-DO-220AA,40V,,,2A,,-55/+150C SAT RC 09 TELIT ANTENNA STAMPATO - Revised: marted, ottobre 20, 2009 3020097802 Revision: 0 METASYSTEM S.P.A. PROPERTY ALL RIGHTS RESERVED ART.1151-1/2/3 IL TECNICO PROGETTISTA: R.ROMAGNOLI IL TECNICO DISEGNATORE: R. ROMAGNOLI DVP-S 159 REV.000 21/10/02 Bill Of Materials Oct 20,2009 14.23.43 Page: 2 Quantity Item ____________________________________________________________________________________ ____ Reference Part 27 3 D4,D5,D6 1520007400,1A 400V,SMD,SOD-123,400V,,,1A 28 1 D8 1520009500,SCHOTTKY,SMD,SMD-DO-214AC,40V,1/2W,,1A 29 2 D9,D12 1520008000,BAV70W,SMD,SOT-323_DX,,,,,,-65/+150C 30 1 D10 1520010300,SCHOTTKY 60V,SMD,SOT23_DX,60V,,,900MA 31 1 D11 1520009300,BAS70-05,SMD,SOT23_DX,,,,,,-55

+125C 32 1 DZ1 1520003900,BZX84-27V,SMD,SOT23_DX,27V,0W3,5%

33 1 DZ2 1520002400,BZX84-15V,SMD,SOT23_DX,15V,0W3,5%

34 1 DZ3 1080007000,PESD12VL1BA,SMD,SOD-323 35 1 DZ4 1520004400,PLVA,SMD,SOT23_DX,5V,,4%,650MA 36 1 DZ5 1520000300,BZX84-3V3,SMD,SOT23_DX,3V3,0W3,5%

37 6 DZ6,DZ7,DZ8,DZ9,DZ10, 1520003800,CAN-ESD,SMD,SOT23_DX,24V DZ12 38 1 DZ11 1520000400,BZX84-4V7,SMD,SOT23_DX,4V7,0W3,5%,,,150C 39 1 EC1 2500005800,CON-18POLI-MAS-90-CS,SMD,CONN-18POLI-O-E10180 40 1 EC2 2500002500,CON-SMD RF GSC,SMD,GSC-MALE 41 1 EC3 2050018100,CONN-SMD.FAKRA-PLUG-,SMD,SMB-CARLOCK-PIP 42 1 EC4 2500001500,CONN-40P-P0.5-V,SMD,CONN-JMD-40P-V 43 1 EC5 2050018200,CONN-SMD.FAKRA-PLUG-,SMD,SMB-CARLOCK-PIP 44 1 EC6 2500007400,ZOCC-SIM-BRIDGEBLOCK,SMD,SIM-HEADER-BRIDGEBLO 45 1 L1 1150009700,FILTRO-EMI-SMD,SMD,0603 46 1 L2 1610009000,10UH,SMD,CDRH4D22,,,,800MA 47 9 L3,L4,L5,L6,L7,L8,L9, 1150009800,FILTRO-EMI-SMD,SMD,0603,,,,3A L10,L11 48 1 L12 1610004200,47NH,SMD,0402 49 1 L13 1610002300,10NH,SMD,0402 50 3 L14,L15,L16 1610005000,100NH,SMD,0402 51 1 L17 1610008800,4U7H,SMD,CDRH4D22,,,25%,2A2 52 1 Q1 1590012500,PUMH2,SMD,SC70-6,,,,100MA Page 2 3020097802_C36 53 1 Q2 1590000800,BC857B,SMD,SOT23_DX 54 2 Q3,Q4 1590010700,BCR116W,SMD,SOT-323_DX 55 1 Q5 1590012600,BC857BS,SMD,SC70-6,,,,100MA 56 1 Q6 1590006900,PNP-1A-45V,SMD,SOT-89,45V,,,1A 57 1 Q7 1590011100,BCR198,SMD,SOT-323_DX 58 1 Q8 1590000500,BC807,SMD,SOT23_DX 59 1 Q9 1590002100,MMBTA42,SMD,SOT23_DX,300V,,,500MA 60 1 Q10 1590009000,STN3PF06,SMD,SOT-223_DX,60V,,,2A5 61 2 Q11,Q12 1590007100,30V-2A,SMD,SOT23_DX,30V,,,2A 62 4 Q13,Q14,Q15,Q19 1590011300,BCR22,SMD,SC70-6 63 3 Q16,Q17,Q18 1590005600,BSS138,SMD,SOT23_DX,50V,,,200MA 64 2 QZ1,QZ2 1150009100,32K768HZ,SMD,Q-A05566,,,,,32K768HZ 65 7 R1,R2,R3,R4,R5,R6,R7 1550013700,1K,SMD,0402,,1/16W,5%

66 1 R8 1550019800,15K,SMD,0402,,1/16W,5%

67 1 R9 1550001200,1,SMD,1206,,1/4W,5%

68 1 R10 1550008800,100,SMD,0805_R_DX,,1/8W,5%

SAT RC 09 TELIT ANTENNA STAMPATO - Revised: marted, ottobre 20, 2009 3020097802 Revision: 0 METASYSTEM S.P.A. PROPERTY ALL RIGHTS RESERVED ART.1151-1/2/3 IL TECNICO PROGETTISTA: R.ROMAGNOLI IL TECNICO DISEGNATORE: R. ROMAGNOLI DVP-S 159 REV.000 21/10/02 Bill Of Materials Oct 20,2009 14.23.43 Page: 3 Quantity Item ____________________________________________________________________________________ ____ Reference Part 69 7 R11,R12,R13,R14,R15, 1550025900,220K,SMD,0402,,1/16W,5%

R126,R127 70 1 R16 1560035400,150K,SMD,0603,,1/10W,1%

71 15 R17,R18,R19,R20,R21,R22, 1550009200,100,SMD,0402,,1/16W,5%

R23,R24,R25,R26,R27 R130,R131,R132,R133 72 1 R41 1550003200,4R7,SMD,0805_R_DX,,1/8W,5%

73 3 R42,R43,R44 1560033600,47K,SMD,0603,,1/10W,1%

74 1 R45 1550007400,47,SMD,0402,,1/16W,5%

75 2 R46,R128 1550013500,1K,SMD,0805_R_DX,,1/8W,5%

76 9 R47,R48,R49,R50,R51,R52, 1550028700,1M,SMD,0402,,1/16W,5%

R53,R54,R55 77 1 R56 1560035200,130K,SMD,0603,,1/10W,1%

78 2 R57,R58 1560037100,620K,SMD,0603,,1/10W,1%

79 4 R59,R60,R61,R62 1550009000,100,SMD,0603,,1/10W,5%

80 43 R63,R64,R65,R66,R67,R68, 1550024200,100K,SMD,0402,,1/16W,5%

R69,R70,R71,R72,R73,R74 R75,R76,R77,R78,R79,R80 R81,R82,R83,R84,R85,R86 R87,R88,R89,R90,R91,R92 R93,R94,R95,R96,R97,R98 R99,R100,R101,R102,R103 R104,R129 81 2 R105,R106 1550017000,4K7,SMD,0402,,1/16W,5%

82 1 R107 1560034100,59K,SMD,0603,,1/10W,1%

83 1 R108 1560032600,33K,SMD,0603,,1/10W,1%

84 3 R109,R110,R111 1550022400,47K,SMD,0402,,1/16W,5%

Page 3 3020097802_C36 85 5 R112,R113,R114,R115,R116 1550015200,2K2,SMD,0402,,1/16W,5%

86 7 R117,R118,R119,R120, 1550019000,10K,SMD,0402,,1/16W,5%

R121,R122,R123 87 1 R124 1560034200,68K,SMD,0603,,1/10W,1%

88 1 R125 1550004200,10,SMD,0805_R_DX,,1/8W,5%

89 1 RK1 1570001200,100K,SMD,0603,,1/10W,3%,,,150C 90 1 RK2 1570000200,PTC,SMD,1812,15V,,,1A 91 1 RN1 1570003100,4K7,SMD,RETE-RES-4-0402,,,5%

92 1 RN3 1570003500,100K,SMD,RETE-RES-4-0402,,,5%

93 6 RN4,RN5,RN6,RN7,RN8,RN9 1570002600,100R,SMD,RETE-RES-4-0402,,,5%

94 1 U1 1540050600,S25FL008A,SMD,SO8-200 95 1 U2 1540005800,74LVC2G14,SMD,SC70-6 96 1 U3 1540029400,LT3481,SMD,DFN-10,,,,2A,2M4HZ 97 1 U4 1150008900,SAFSE1G57,SMD,Q-A05564,,,,,1G57HZ,,SAW G 98 5 U5,U6,U7,U8,U9 1540029800,LP5951-3V3,SMD,SC-70,3V3 99 1 U10 1520001000,5V6,SMD,SC74,5V6 100 1 U11 1540050400,M32C87A,SMD,QFP100-P 101 1 U12 1150009000,TCXO-3225-16M3683HZ,SMD,Q-A05565,,,+/-3PPM,,16M3683HZ SAT RC 09 TELIT ANTENNA STAMPATO - Revised: marted, ottobre 20, 2009 3020097802 Revision: 0 METASYSTEM S.P.A. PROPERTY ALL RIGHTS RESERVED ART.1151-1/2/3 IL TECNICO PROGETTISTA: R.ROMAGNOLI IL TECNICO DISEGNATORE: R. ROMAGNOLI DVP-S 159 REV.000 21/10/02 Bill Of Materials Oct 20,2009 14.23.43 Page: 4 Quantity Item ____________________________________________________________________________________ ____ Reference Part 102 1 U13 ,SIM-SMD-QFN8,SMD,VQFN-8 103 1 U14 ,STG3690-QFN16,SMD,QFN-16-3X3 104 1 U15 1540048900,SMA661AS,SMD,SOT-666,,,,,,,LNA G 105 1 U17 1540033400,STM6822,SMD,SOT23-5,2V7 106 1 U18 1540050500,GPS-TESEO-MCM,SMD,BGA-104-7X11 107 1 U19 1540029600,LP5951-2V8,SMD,SC-70,2V8 108 1 U20 1540050900,MASWSS0143,SMD,SOT23-6,,,,,,-40/+85C 109 1 U21 2110043300,TELIT GE864-QUAD7030,SMD,GE864 110 1 X1 1150007000,8MHZ,SMD,Q-CSTCE-G,,,,,8MHZ Numero totale Componenti SMD: 353

------ Componenti Tradizionali ---------------------------------------------

Page 4