FCC ID: ZKQ-WB100 WB100

WB100 USER MANUAL PARKING LIST User manual WB100 Charging cable DIAGRAM SOS BUTTON MIC POWER BUTTON LED VOICE BUTTON TEST BUTTON SPEAK POWER ON Mode 1 Press the power button for 3 seconds Mode 2 USB cable charging CHARGING LED Charging Fully Charged FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference received, including interference that may cause undesired operation. Note:This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequence energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.if this equipmemt does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an autlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. Specific Absorption Rate (SAR) information:

This WB100 meets the government's requirements for exposure to radio waves. The guide lines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) are 4.0 W/kg averaged(Wrise-

worn) and 1.6W/kg averaged(Next-to-Mouth) over one gram of tissue. Device types: WB100 (FCC ID:

ZKQ -WB100) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification are 0.746W/kg (Wrise-worn) and 0.432 W/kg(Next-to-Mouth). This device was tested for typical body-worn operations with the back of the WB100 kept 00mm from the body and Next-to-Mouth 10mm. To maintain compliance with FCC RF exposure requirements, use accessories that maintain 00cm and 10mm separation distance between the user's body and the back of the WB100 . The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Section 2.911(d)(5)(i) Certification Equipment Type Company name: Micron Electronics LLC. Address: 1001 Yamato Road Suite 400 Boca Raton,Flonda 33431 United States Product Name: WB100 FCC ID:ZKQ-WB100 Model(s): WB100 2.911(d)(5)(i) Equipment Type We,Micron Electronics LLC.(the applicant) certify that the equipment for which authorization is sought through certification is not:

Prohibited from receiving an equipment authorization pursuant to 2.903; of the FCC rules. Identified as an equipment type in the Covered List NOTE 1 Yours sincerely, Name:

Date:2023.08.03 Title:Director Company name:Micron Electronics LLC. NOTE 1 Covered List; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References;

1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the 2.911 (d)(5)(i) Equipment Type Attestation v1.2

Section 2.911(d)(5)(ii) Certification Applicant (Covered List) Company name: Micron Electronics LLC. Address:1001 Yamato Road Suite 400 Boca Raton,Flonda 33431 United States Product Name:WB100 FCC ID:ZKQ-WB100 Model(s):WB100 2.911(d)(5)(ii) Applicant filing We,Micron Electronics LLC. (the applicant) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the Covered List NOTE 2, established pursuant to 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name:

Date: 2023.08.03 Title and Company name:Director, Micron Electronics LLC. NOTE 1 Delete option not applicable to this application. NOTE 2 Covered List; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References;

1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the 2.911 (d)(5)(ii) Applicant Attestation v1.3

Micron Electronics LLC. Section 2.911(d)(7) USA Agent for Service of Process Company name: Micron Electronics LLC. Address: 1001 Yamato Road Suite 400 Boca Raton,Flonda 33431 United States Product Name: WB100 FCC ID: ZKQ-WB100 Model(s): WB100 2.911(d)(7) USA Designated Agent for Service of Process We, [Micron Electronics LLC.] (the applicant) designate [Micron Electronics LLC.]

NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either we the grantee have permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Applicant Company name:

Micron Electronics LLC. USA Address:

1001 Yamato Road Suite 400 Boca Raton,Flonda 33431 United States Company name:

Micron Electronics LLC. Address:

1001 Yamato Road Suite 400 Boca Raton,Flonda 33431 United States FRN Number0020840385 Contact Name: Ping Cheng Telephone No: 888-538-3489 Email:

pcheng@simcom.us FCC Grantee Code: ZKQ Contact Name: Ping Cheng Telephone No: 888-538-3489 Email: pcheng@simcom.us Signature:

Title: Director Date: 2023-08-21 Signature:

Title: Director Date: 2023-08-21 2.911 (d)(7)USA Agent v1.4 Micron Electronics LLC. NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the 2.911 (d)(7)USA Agent v1.4

Micron Electronics LLC. Agent Authorization Company: Micron Electronics LLC. Address:1001 Yamato Road Suite 400 Boca Raton,Flonda 33431 United States Product Name: WB100 Model Number(s): WB100 Product Description: WB100 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Ping Cheng Title:

Director Company: Micron Electronics LLC. Date: 2023-08-03

Micron Electronics LLC. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject; Request for Long Term Confidentiality FCC ID: ZKQ-WB100 Date: 2023-08-15 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram BOM Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Ping Cheng Title: Director