FCC ID: 2A22E-WWYLT262 AX1500 Wi-Fi 6 Router

User Guide AX1500 Wi-Fi 6 Router T262-T21D Specifications:

WiFi Standard: IEEE802.11b/g/n IEEE802.11a/n/ac/ax Interface: 1 WAN 3 LAN Environment:

Rated Power Input:

12VDC, 1A Operating Temperature: 0-40 Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Safety Instruction 1.WARNING: To reduce the risk of fire or electric shock, do not expose this device to rain or moisture. The device shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus. 2.WARNING: the power plug/direct plug-in adpater is used as disconnect device, the disconnect device shall remain readily operable. 3. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer or service operator where the product was purchased. They can take this product for environmental safe recycling. 4.Warning: to reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel. 5.The power adapter is used as the power interrupting d evice. Please pay attention to safety plug and pull and convenient operation. 6.Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel. 7.Use only the AC adapter which is included in the product package. Any other adapter may cause damage to the device. Such damage is not covered under warranty. 8.Please use and store the router and its accessories within the temperature range of 0~40. When the temperature is too high or too low, it may cause equipment failure. 9.WARNING: The direct plug-in adapter is used as disconnect device, the disconnect device shall remain readily operable. FCC Warning Statement FCC Radiation Exposure Statement:

The antennas used for this transmitter must be installed to provide aseparation distance of at least 20cm from all persons and must not be co-located for operating in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna. 2.Increase the separation between the equipment and receiver. 3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4.Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation 1. Connect the Router 1.1 The first step to start configuring your router is to plug it in and then connect a network cable RJ45 to your WAN port, the other side of network cable (RJ45) must also be connected to your home Modem (xDSL/PON). 1.2 After plugging in the router and connecting it to the Modem, proceed to the next topic, which is the configuration step by step. 1.3 If your internet connection is through an Ethernet cable from the wall instead of through a home Modem (xDSL/PON) , connect the Ethernet cable directly to the routers Internet port. Connect the router's WAN port with the Ethernet cable 3 Connect the modems LAN port with the Ethernet cable 2 Power off or unplug your modem 1 6 Switch on the router. And waiting for the LED turns into green. 4 Connect the power adapter cable to the routers DC-IN and turn it on. 5 Plug the router and modems power adapter. 2. Indicator LED Status Description Off The router is power off Red Green On On The router is power on but Internet is not working The router is already connected to the internet Green Flashing WPS or Mesh pairing 3. Connect Device to the Router 3.1 Wireless Activate the Wi-Fi on your smartphone or notebook, connect to the router's 2.4GHz or 5GHz network with the SSID provided at the bottom of the router and enter the IP address 192.168.10.1 in any browser;

Find the SSID and SSID password printed on the label at the bottom of the router. Click the network icon of your computer or go to WiFi settings of your smart device, and then select the SSID and input password to join the network. 3.2 Wired Connect a network cable(RJ45) to the LAN port of the router and the other side of network cable(RJ45) connect to a notebook or desktop and enter the IP address 192.168.10.1 in the browser. Remember to turn off the device's Wi-Fi before performing this step. 4. Configure your router via Web Open the mobile phone or computer browser, visit the 192.168.10.1 website, enter the default Username and Password on the label at the bottom of the router, then you can enter the router management page. When the router is configured for the first time, it will automatically enter the Install page (setup wizard). Select WAN Access Type , normally DHCP Create a password for each Wi-Fi band (2.4GHz and 5GHz) and if you want, change the SSID (2.4GHz and 5GHz) to your preference name . Save the configuration , enjoy the Internet. Notice : For the WAN Access Type depend on ISP , you can consult the ISP for confirmation. 5. WAN Access Type 5.1 DHCP: For Cable/DSL/Broadband connection which makes your computer immediately online without any setting or signing-in. 5.2 Static IP: You are provided with specified IP parameters by your ISP. 5.3 PPPOE: Usually for ADSL Modem and you are provided with a PPPoE username and password by your ISP. 6. Mesh pairing If you have purchased two or more AC1200 units, follow the steps below to perform the MESH pairing between the routers and enjoy a connection with a wide signal range. 6.1 Mesh pairing One button 6.1.1. Before turning on the second (Agent) router, make sure that the first (Controller) router connected has internet access and is fully configured;

6.1.2. Plug in the second (Agent) router;

6.1.3. Click and hold the first (controller) router's WPS button for about 8 seconds, then the LED will start flashing;

6.1.4. Then, repeat the process on the second (Agent) router, click and hold the WPS button for about 8 seconds and release, then the LED will start flashing too;

6.1.5. Wait for approximately 3 minutes while the routers are paired, once the process is completed, the LED of both routers should be green;

6.1.6. Once connected, move the second (Agent) router to the place where the signal needs to be expanded (just unplug it and plug it in again in the place you prefer), wait approximately 3 minutes until the connection is re-established and check if the LED lights up, keeps with the green light on and the signal stable. Note: To connect more AC1200 units to the network, just repeat the step by step above. 6.2 Mesh Unpairing You can unpair the meshed router by restore the router to its factory default settings. For resetting router, press and hold the RESET button more than 8 seconds then release , the LED will start to blink and change into red. 6.3 Notice After completing EasyMesh networking, the Controller router will synchronize its 2.4GHz and 5GHz SSID, password, and channel with the Agent router. That is, these configurations of the Agent router will be the same as the Controller router. After modifying the SSID, password, and channel on the Controller router, the Controller router will synchronize these configurations to all Agent router. Modifying the SSID and password on the Agent router will not be synchronized. After the router restarts with a power failure, the routers will restore the EasyMesh network group by default, and no connection settings are required. If the EasyMesh function of the Controller router is disabled, the entire EasyMesh network will be disabled. If the EasyMesh function of the Agent router is disabled, the router will leave the EasyMesh network. If you need to switch the access mode of a certain Mesh router, you need to turn off the Mesh function of the router first, and then turn on the Mesh function to complete the switching of the access mode. The Agent router is not supported to connect to other Mesh routers via Wi-Fi and wired at the same time. That is, the Agent router can only use one of Wi-Fi and wired to connect to other Mesh routers. 7. FAQ Q1: What should I do if I can't access the routers management page?

Reboot your router and try again. Check your Wi-Fi connection. Use another Web browser such as Google Chrome. Restart your device. Q2: What should I do if I can't access Internet?

Reboot your modem and router, then try again. Check the Internet is working. With an Ethernet cable connecting the modem to computer directly. Q3: What can I do if I forget my wireless network password?

If you have not changed the default wireless password, it can be found on the label at the back of the router. Connect your computer to the router via an Ethernet cable. Log in to the web management at IP Address: 192.168.10.1 and go to Install > Wireless to retrieve or reset your wireless password. Q4: What should I do if I forget my Web management page password?

Check the Web password on the label at the bottom of the router. When the router is power on, use a pin to press and hold the RESET button on the back until the LED blinks. Then the password will restore to the default that marked on the label. Manufacturer Information Micronet Union Technology(Chengdu) Co., Ltd. Address: Room 502, Building 5, No. 528, Yuefei Road, Shibantan Street, Xindu District, Chengdu, Sichuan, China

AX1500 Wi-Fi 6 Router IPeddess: 192 16810. CEG SY =

Poweradapter: 12V= 1A FCCID: 2A22E-WWYLT262 Manufacture: Micronet Union Technology(Chengdu) Co.,Itd Username: admin Password: admin 2.4G SSID: Router_XXXX 5G SSID: Router_XXXX_5G 2.4G/5G SSID password: 123456789 S/N (NATTA TMNT UXXXXXXXXXXXXXXXK UXXXXXXXKAKAAAAEE Made in China 87mm 35mm 40 50 60 70 80 90100 19 20 30 49 ll uy ll UU i |

uu QL 02 OE Or OS 09 OL 0B 06 | OL Oz OF OF OS 09 OL OB 060K suuiliilivnslinnlinilivnliny duuduvilanelivanccelaneliveataralovnuv 2 all Pe et 1 Sz 3= :

Rg: i +

= Hu innate winitt s: CE@ GE -

= bd

> aa Oyun Myiit | RT OL 02 OF OF 0S 09 OL 8 06 (\)} OF Oz OF OF 0S 08 OL BO

& 06 Or 05 09 OL 08 vo OOb OF OZ OF OF OF 09 OL 08 06008 OF oF OF 0 MMII mmm AX1500 Wi-Fi 6 Router IPeddess: 192 16810. CEG SY =

Poweradapter: 12V= 1A FCCID: 2A22E-WWYLT262 Manufacture: Micronet Union Technology(Chengdu) Co.,Itd Username: admin Password: admin 2.4G SSID: Router_XXXX 5G SSID: Router_XXXX_5G 2.4G/5G SSID password: 123456789 S/N (NATTA TMNT UXXXXXXXXXXXXXXXK UXXXXXXXKAKAAAAEE Made in China 87mm 35mm Cy Ob 02 OF 0 05 09 04 08 06 002 oF a2 9 6 Or 0S 09 OL 08 Sill AX1500 Wi-Fi 6 Router IPeddess: 192 16810. CEG SY =

Poweradapter: 12V= 1A FCCID: 2A22E-WWYLT262 Manufacture: Micronet Union Technology(Chengdu) Co.,Itd Username: admin Password: admin 2.4G SSID: Router_XXXX 5G SSID: Router_XXXX_5G 2.4G/5G SSID password: 123456789 S/N (NATTA TMNT UXXXXXXXXXXXXXXXK UXXXXXXXKAKAAAAEE Made in China 87mm 35mm ll sill MMi ll Z 4 Zz zZ Z Zz zZ z Z Z S

# OL 09 05 OP dE 02 Ot OO) 06 08 dz

% 01 O06 06 og

C5266091_X24_Ed.1 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization Applicant Company name: Micronet Union Technology(Chengdu) Co., Ltd Grantee code: 2A22E FCC ID:

Contact Name:

Address:

Sichuan, China Telephone No:

Fax No:

Email:

+0086-018262619637 028-81265178 zhongshunyu@cjdgy.com 2A22E-WWYLT262 Snow Zhong Room 502, Building 5, N.O. 528, Yuefei Road, Shibantan Street, Xindu District, Chengdu, i. ii. Micronet Union Technology(Chengdu) Co., Ltd (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. Micronet Union Technology(Chengdu) Co., Ltd (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification. Date: 2023/02/09 Applicants Name: Snow Zhong Title: Senior Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

C5266091_X10_Ed.2 Micronet Union Technology(Chengdu) Co., Ltd Room 502, Building 5, N.O. 528, Yuefei Road, Shibantan Street, Xindu District, Chengdu, Sichuan, China Snow Zhong Phone: +0086-018262619637 Email: zhongshunyu@cjdgy.com Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2A22E-WWYLT262 To Whom It May Concern, Date: January 31, 2023 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality Short-Term Confidentiality NOTE 2 No No No No No NOTE 1 NOTE 1 No No No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 Sincerely, Signature:

Name: Snow Zhong Title: Senior Manager

Micronet Union Technology(Chengdu) Co., Ltd. Subject: Declaration letter We: Company Name: Micronet Union Technology(Chengdu) Co., Ltd Address: Room 502, Building 5, N.O. 528, Yuefei Road, Shibantan Street, Xindu District, Chengdu, Sichuan, China Product Name: AX1500 Wi-Fi 6 Router;

Model Number: T262-T21D, T262-T21X, T262-BXX, T262-PQX, (the last X=A-Z or a-z, which indicates for different appearance, dimension and color.) FCC ID: 2A22E-WWYLT262;

They have the same circuit and the only difference is antenna and appearance, All models share five appearance; EUT1, EUT4 and EUT5 have the identical antenna, EUT2 and EUT3 have the identical antenna. EUT1 EUT4 EUT5 EUT2 EUT3 Applicant: Micronet Union Technology(Chengdu) Co., Ltd Sincerely, Signature:

Name: Snow Zhong Title: Senior Manager file: declaration letter-template Page 1 of 1

C5266091_X8_Ed.1 Micronet Union Technology(Chengdu) Co., Ltd Room 502, Building 5, N.O. 528, Yuefei Road, Shibantan Street, Xindu District, Chengdu, Sichuan, China ____________________________________________________________________________ Company: Micronet Union Technology(Chengdu) Co., Ltd Address:

Xindu District, Chengdu, Sichuan, China Room 502, Building 5, N.O. 528, Yuefei Road, Shibantan Street, Product Name: AX1500 Wi-Fi 6 Router Model Number: T262-T21D, T262-T21X, T262-BXX, T262-PQX, (the last X=A-Z or a-z, which indicates for different appearance, dimension and color.) FCC Identifier:

2A22E-WWYLT262 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Snow Zhong Date: January 31, 2023 Title: Senior Manager Signature of applicant:

1/1

Micronet Union Technology(Chengdu) Co., Ltd Room 502, Building 5, N.O. 528, Yuefei Road, Shibantan Street, Xindu District, Chengdu, Sichuan, China ____________________________________________________________________________ FCC Software Configuration Control Declaration Date: January 31, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Product/ Model Number: AX1500 Wi-Fi 6 Router / T262-T21D, T262-T21X, T262-

BXX, T262-PQX, (the last X=A-Z or a-z, which indicates for different appearance, dimension and color.) FCC ID: 2A22E-WWYLT262 Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Signature of applicant Name: Snow Zhong Title:

1/1