FCC ID: O7KML3215 32 Channel Mobile Radio

ProLine Series ML3215 /

ML3245 Operating Table of Contents 1 FCC RF Exposure Compliance Requirements - for Occupational Use Only........ 1 Safety Information................................... 2 About Topaz3............................................. 2 About Your Legacy ProLine Radios............. Unpacking and Checking Equipment.......... 2 Radio Control Buttons / Operation Features... . 3 Radio Operation....................................... Transmit................................ Radio Functions....................................... 4 Power On /

Tone 4 4 Signaling.........................4 Scan Modes......................................... 5 Scan.......................... 5 Priority Scan TX ............................ Normal Channel 5 Priority Look Back Scan 5 Mode Operation and Function Setup............. ............ Priority Select Scan.............. Vacant Channel Scan............,, Nuisance Delete..................................... Busy Channel Lockout............................ Marked Idle............................................ TX Delay................................................ Time-Out-Timer (T-O-T)............................. Time-Out-Timer Penalty (TX Inhibit)............. Two-Tone Decode.................................. VOX (Voice Operated X-mit) .............. P/A Mode .................................. 5 5 5 5 5 5 5 5 5 5 5 6 Power On............ 6 Channel Change............ 6 Transmit .............. 6 6 Channel Option View.............. 6 Channel Option Settings Menu ........... System Option Settings Menu ............ 10 Display Option Settings Menu ............ 13 P/A Option Settings Menu ............ 14 ACC-733 DTMF Microphone Operation............... 14 15 Licensing and Service Information... 15 FCC Licensing....................................... 15 Service................................................ Maintenance........................................... 15 Software Copyrights................................ 16 Topaz3 / Legacy Product Warranty..........16 FCC RF Exposure Compliance Requirements -

for Occupational Use Only The Federal Communications Commission (FCC), with its action in General Docket 93-62, November 7, 1997, has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Topaz3 / Maxon subscribes to the same safety standard for the use of its products. Proper operation of this radio will result in user exposure far below the Occupational Safety and Health Act (OSHA) and Federal Communications Commission limits. Antennas used for this transmitter must not exceed an antenna gain of 0dBd. The radio must be used in vehicle-mount config-

urations with a maximum operating duty factor not exceeding 50%, in typical push-to-talk configurations. This radio is NOT approved for use by the general population in an uncontrolled environment. This radio is restricted to occupational use, work related operations only where radio operator must have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining the minimum separation distance of 47.7 inches (121 cm) between any persons and the antenna. Failure to observe these restrictions will result in exceeding the FCC RF exposure limits. CAUTION - DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the TX icon on the radio display is illuminated. You can cause the radio to transmit by pressing the P-T-T button on the radios microphone. CAUTION - DO NOT operate the transmitter of ML3215, ML3245 mobile radios when someone

(bystanders) outside the vehicle is within 47.7 inches (121 cm) of the antenna. Antenna installation must be limited to the center of the roof-top of a vehicle where the passengers are below the metallic ground plane (roof-top) to ensure compliance. NOTE: This radio operates in FCC regulated frequency bands. All radios must be licensed by the FCC before use. Because this radio contains a transmitter, Federal law prohibits unauthorized use or adjustments of this radio. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Safety CAUTION - DO NOT operate the transmitter of any radio unless all RF connectors are secure and any open connectors are properly terminated. CAUTION - DO NOT operate the radio near electrical blasting CAUTION - All equipment must be properly grounded for safe WARNING - DO NOT allow children to operate transmitter - equipped radio equipment. WARNING - All equipment should be serviced by a qualified technician. WARNING - It is mandatory that radio installations in vehicles fueled by liquefied petroleum gas conform to the following caps or in an explosive atmosphere. operation. standard: National Fire Protection Association Standard NFPA 58 applies to radio installations in vehicles fueled by liquefied petroleum (LP) gas with LP gas container in the within the interior of the vehicle. This standard requires that:

trunk or other sealed-off space 1. Any space containing radio equipment shall be isolated by a seal from the space in which the LP gas container and its fittings are located. 2. Remote (outside) filling connections shall be vented to the outside. About Topaz3 Topaz3 is the exclusive supplier of Maxon, Legacy and TruTalk brand communication products. Our product line ranges from FCC licensed two-way radios suitable for Business and Industry (B&I) markets like farm, government, law enforcement, utility, etc. to consumer communications equipment for recreational and light-duty business markets. Product offerings include a variety of UHF and VHF handheld and mobile radios, repeaters and RF link modules as well as GMRS (General Mobile Radio Service) radios, MURS (Multi User Radio Service) radios, Citizens Band radios and weather monitors. Available accessory items include a variety of carrying cases, spare batteries, desktop and mobile chargers, ear bud speaker microphones and more for each radio model. For additional information on our product line, visit our website: www.topaz3.com About Your Legacy ProLine Radio The Legacy ProLine models ML3215 (VHF) and ML3245 (UHF) are fully programmable, synthesized radios featuring:

32 Channels of operation 8-Character alphanumeric display 2 or 45 Watts output power Channel scan 38 Standard and 11 non-standard CTCSS tones 104 DCS Codes Approved to MIL-STD810F specifications Scan channel delete Busy channel lockout Programmable CTCSS / DCS tones and two-tone decode Wide / narrow channel spacing TX Inhibit VOX operation Public address mode Nuisance Delete Die-cast aluminum frame, polycarbonate cabinet Please read this manual thoroughly before operating the radio. Application of some functions described in this manual are determined by the system you use. Your radio communications Dealer will program your radio for you to have the greatest number of functions possible relative to your needs. Should you have questions regarding the operation of this radio, consult your radio communications Dealer, or contact the Topaz3 Customer Service Department: 1-800-821-7848, Ext. 499. Unpacking Information Carefully unpack the radio and its accessories. Use the item list below to identify the components included in the product packaging, to ensure that no items are discarded in the packing materials. Radio Body Microphone Mounting hardware Mounting Bracket Operating Instructions Radio Control Buttons / Operation Features Radio Front A. Power / volume control - Powers radio on and adjusts radio volume. B. Squelch control adjust radio carrier squelch setting. C. Microphone jack Attaches standard microphone or optional DTMF microphone. D. Backlit LCD - Provides visual confirmation of radio settings. E. T/A button Bypass a repeater tower on a repeater channel pair for radio to radio communications. F. Scan button Enters channel scanning of channels in scan list. G. Mode button Enters menu tree for turning on / off radio features and functions. H. Monitor button - Press and hold to turn radio squelch off; release to turn squelch on. I. Weather Selects NOAA weather channels, press scan to scan for nearest weather channel. J. Auxilary button Toggles on or off an installed option. K. Channel selector buttons Selects channel and used in conjunction with mode button. L. Speaker E A G F H D L B C J K I Radio Back A. Antenna connector B. 15 pin interface connector C. 3.5 mm mono external speaker jack D. 13.8V DC Power cord A D B C Backlit LCD Features function indicators. A. 8-Character alphanumeric display - Shows current channel setting, CTCSS or DCS tone code setting, and other B. Transmit (TX)) indicator C. Receive (RX) indicator D. Voice Operated Transmission (VOX) indicator - Shows VOX operation is active, allowing hands-free radio transmissions E. Monitor (MON) indicator Shows monitor mode (used to open squelch and check for channel activity). F. Time Out Timer (TOT) indicator - Shows transmit timer mode is active, which prevents transmissions when timer expires. G. Weather (WX) Shows NOAA weather station mode. H. T/A - Shows repeater bypass activated. I. Auxiliary (AUX) Shows internal auxiliary option is active. J. Scan (SCAN) indicator - Shows scan function is active. K. Audible Tone (BEEP) Indicator - Shows "beep" tone function is active. L. High power (H) indicator - Shows high power is active (used for increased range and penetration). M. Low power (L) indicator - Shows low power is active (used for battery conservation in short range conditions). B C D E F G H I J K M L A Radio Operation Power On / Transmit Power on the radio by turning the power / volume control (A) clockwise out of detent. You will hear a confirmation tone on power-up and display will show the control to desired volume level. To check the radio volume, press and hold the monitor button (B) then rotate A B C Adjust the squelch setting located behind the volume control by rotating the squelch control (C) counter clockwise for loose squelch and fully clockwise for tight squelch. Press up or down channel selector buttons to choose the desired channel. Press the monitor button to check the channel for activity. To avoid interrupting another user, make sure the channel is clear before you begin transmitting. To transmit, place the radio microphone approximately 2 (5 cm) from your mouth. Press and hold the P-T-T bar while speaking in a normal tone. Release the P-T-T bar when you are finished speaking; the radio will be placed into receive mode. Radio Functions Tone Signaling To help block out unwanted calls to your ProLine ML3215 / ML3245 can be programmed to look for privacy tones. Scan Modes Scanning is a Dealer programmable feature that allows you to monitor a number of channels. Your radio communications Dealer will help you define a scanning mode and your channel "scan list". Once the scan list has been established, initiate scan by pressing the SCAN button. The the lower right corner of the display to confirm radio scanning. icon will show in Normal Channel Scan If a conversation is detected on any of the channels in the scan list, the radio will stop on that channel and you will be able to hear the conversation. In normal scan, you can transmit on that active channel during the programmable scan delay time. (The scan delay time is the amount of time the radio will stay on that channel once activity has ceased. Dealer programmable, 4 7 seconds is typical). The radio will resume scanning once the scan delay time has expired, and will continue to scan until the channel is changed. In scan mode, if radio power is turned off and on, the radio will return to the scan mode until a channel is changed. Priority Scan TX A single channel may be programmed as the "Priority" channel. Priority channel activity takes precedence over all other conversations. During the scan mode, if a P-T-T is initiated the radio will transmit on the Priority channel. The radio will constantly monitor this channel while scanning and when stopped on an active channel. If a call is detected on the priority channel, the radio will automatically move to, and remain on, the Priority channel. Priority Lookback Scan A single channel may be programmed as the Priority channel. The radio will constantly monitor this channel while scanning and when stopped on an active channel. If a call is detected on the Priority channel during a conversation, the radio will automatically move to, and remain on, the Priority channel. Priority channel activity takes precedence over all other conversations. Priority Select Scan A selected channel becomes the Priority channel. As you change the channel, that channels frequency will become your new Priority channel. Priority channel activity takes precedence over all other conversations. Nuisance Delete During receiving a signal or scan delay time, if the MON (monitor) button is pressed, the current receiving channel is deleted in scan list and is no longer scanned. When the power is turned off and on, the deleted channel is restored to the scan list. Busy Channel Lockout When the RX signal is being received, the radios transmitter is disabled. Marked Idle When used in conjunction with Busy Channel Lockout (BCLO), the radio will allow a transmission if the correct tone is present with the received signal. TX Delay The transmission will remain active for approximately 180 milliseconds even though the P-T-T bar is released when using CTCSS Tones. This eliminates squelch tail. Time-Out-Timer (TOT) The purpose of the time-out-timer is to prevent any single person from using a channel for an extended period. The time-out time can be programmed from 10 seconds to 990 seconds. Time-Out-Timer Penalty (TX Inhibit) When time-out-timer is applied, transmission will be inhibited after the time-out-time time expires. This TX inhibit time can be selected and programmed by your radio communications Dealer from 1 second to 100 seconds. For instance, when the time-out time is set to 3 minutes and T-O-T penalty is set to 5 seconds, if you continuously transmit for 3 minutes, the radio will stop transmitting. A tone will sound with each P-T-T bar press until the 5 second TX inhibit time expires. Press the P-T-T bar after the TX inhibit time expires to resume transmitting. Two-Tone Decode Each channel can be programmed with two-tone decode selections: Individual Call, Group Call and Super Group Call. Your radio communications Dealer can program your radio(s) for this feature. To activate or reset the two-tone decode, press and hold the AUX button for 3 seconds. After two-tone is decoded an alarm will sound if two tone alarm is turned on. VOX (Voice Operated TX) Allows your radio to transmit with the sound of your voice for hands-free operation. Your radio has a VOX sensitivity level adjustment for noisy or windy conditions. The VOX icon will be displayed when option is active. P/A Mode Allows your radio to become a public address system with an optional external speaker connected. In this mode only microphone audio heard over the optional external speaker when the P-T-T bar is pressed. Mode Operation and Function Set Up Depending on how your Dealer has programmed your radio, you may be able to change certain modes and functions of your radio. Consult with your radio communications Dealer regarding which functions are available with your radio. The following identifies display prompts for various radio functions. NOTE: All functions are activated or turned off by pressing the MODE button. Use the up or down buttons to toggle through the choices available with each function. To exit, press the MODE or P-T-T bar on the microphone. Power On Power on the radio by turning the power / volume control knob clockwise out of detent. The radio will perform a self-check, showing operation mode. If power-on detects an error to data in the last memory, the and an error tone will beep. in the display. Two beeps are sounded when the radio is ready to enter normal display will appear, Channel Change Press and release the up or down. Your display will change with each channel selection, and will vary depending on how your Dealer programmed each channel description. A press and hold of up or down will scroll trough the channels. Transmit Press the P-T-T bar to transmit on the microphone; release to receive. Both TX (transmit) and RX (receive) are indicated by display icons. When the VOX option is set and activated by voice, the radio transmits; if voice input stops, the radio maintains TX for around 2 seconds, then returns to receive mode. Channel Option View In receiving mode, if the MON (monitor) button is pressed for more than 2 seconds, the RX tone option and the TX tone option for each channel selected will display. This display example identifies:

Receive, CTCSS, Tone 1 This display example identifies:

Transmit, CTCSS, Tone 1 Channel Option Settings Menu NOTE: These setting instructions are per-channel. You must repeat for all channels. To enter the Menu setting, press and release the MODE button during the receive or standby mode. In the menu setting, use the up or down buttons to scroll through the sub-menu settings. To enter a sub-menu, press the MODE button when the desired sub-menu appears on screen, then press the up or down buttons to scroll through the sub-menu selections. To activate or turn off a sub-menu setting, press and release the MODE button. The radio will save the setting, and return to standby mode. If the P-T-T button is pressed, the radio returns to standby mode. If the MON (monitor) button is pressed, the radio will return to the previously displayed Menu setting. The Channel Options Settings menu and sub-menus are detailed on the next few pages Press up or down to the desired channel. Press the MODE button and then the up or down button until appears. Press and release the MODE button to select. Sub-menu settings include:

, and

. Scroll through the sub-menu settings with the up or down buttons. To enter a sub-menu, press the MODE button when the desired sub-menu appears on screen. settings include:

You can toggle between these settings with the up or down buttons. When the desired setting appears on screen, press the MODE button. Under the RX Tone and TX tone settings, your choices toggle between and Coded Squelch tones).

(No Tone, Continuous Tone Coded Squelch System tones, Digitally Coded Squelch tones and Invert Digitally

, If you choose the CTCSS tone setting, you will need to use the up or down buttons to select the desired tone code of 49 available. If you choose CTCSS code 1, your display will read:

If you choose CTCSS code 49, your display will read:

When the desired CTCSS tone code appears on the display, select and set your choice by pressing the MODE button or the P-T-T. The radio will save your selection and return to standby mode. CTCSS Tone Signaling Frequency Table No. Freq. No. 01 02 03 04 05 06 07 08 09 10 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 11 12 13 14 15 16 17 18 19 20 Freq. 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 No. Freq. No. Freq. No. 21 22 23 24 25 26 27 28 29 30 136.5 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2 31 32 33 34 35 36 37 38 39 40 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 69.3 159.8 41 42 43 44 45 46 47 48 49 Freq. 171.3 177.3 183.5 189.9 196.6 199.5 206.5 229.1 254.1 If you choose the DCS tone code setting, you will need to use the up or down buttons to select the desired tone code of 105 available. If you choose DCS code 023, your display will read:

If you choose DCS code 754, your display will read:

When the desired DCS tone code appears on the display, select and set your choice by pressing the MODE button or the P-

T-T. The radio will save your selection and return to standby mode. DCS Tone Signaling Frequency Table DCS Code 023 025 026 031 032 036 043 047 051 053 DCS Code 054 065 071 072 073 074 114 115 116 122 DCS Code 125 131 132 134 143 145 152 155 156 162 DCS Code 165 172 174 205 212 223 225 226 243 244 DCS Code 245 246 251 252 255 261 263 265 266 271 DCS Code 274 306 311 315 325 331 332 343 346 351 DCS Code 356 364 365 371 411 412 413 423 431 432 DCS Code 445 446 452 454 455 462 464 465 466 503 DCS Code 506 516 523 526 532 546 565 606 612 624 DCS Code 627 631 632 654 662 664 703 712 723 731 DCS Code 732 734 743 754 If you choose the IDCS tone code setting, you will need to use the up or down buttons to select the desired tone code of 105 available. If you choose IDCS code 023, your display will read:

If you choose IDCS code 754, your display will read:

When the desired IDCS tone code appears on the display, select and set your choice by pressing the MODE button or the P-

T-T. The radio will save your selection and return to standby mode. IDCS Tone Signaling Frequency Table IDCS Code 754 743 734 732 731 723 712 703 664 662 IDCS Code 654 632 631 627 624 612 606 565 546 532 IDCS Code 526 523 516 506 503 466 465 464 462 455 IDCS Code 454 452 446 445 432 431 423 413 412 411 IDCS Code 371 365 364 356 351 346 343 332 331 325 IDCS Code 315 311 306 274 271 266 265 263 261 255 IDCS Code 252 251 246 245 244 243 226 225 223 212 IDCS Code 205 174 172 165 162 156 155 152 145 143 IDCS Code 134 132 131 125 122 116 115 114 074 073 IDCS Code 072 071 065 054 053 051 047 043 036 032 IDCS Code 031 026 025 023 To set the per-channel radio transmit output power, press and release the MODE button, then the up or down buttons until appears. Press the MODE button to select. Scroll through the sub-menu settings with the up or down buttons, press the MODE button when appears. Settings include:

You can toggle between these per-channel settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. The radio will save your selection, and return to standby mode. The display will show an H or an L to confirm High (45 Watt) or Low (2 Watt) output power setting for the current channel. To set the normal scan list on/off setting, press and release the MODE button then the up or down buttons until the display appears. Press and release the MODE button again to select. Scroll through the sub-menu settings with the up or down buttons, press the MODE button when appears on screen. appears. Settings include:

You can toggle between these settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. The radio will save your On or Off selection for the current channel, and return to standby mode. NOTE: Your radio will only scan channels with the scan setting On. To set the Priority scan list on/off setting, press and release the MODE button then the up or down buttons until the display appears. Press and release the MODE button again to select. Scroll through the sub-menu settings with the up or down buttons, press the MODE button when appears on screen. Settings include:

and

. You can toggle between these settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. The radio will save your On or Off selection for the current channel, and return to standby mode. NOTE: This setting is linked to the Priority Scan sub-menu in the System Option menu, detailed following this section. If Priority Scan option of System Option menu is on, Priority scan works only when the channel selector is positioned to the channel with PSCAN ON displayed. To set the two-tone option, press the MODE button then the up or down buttons until the display appears. Press and release the MODE button again to select. Scroll through the sub-menu settings with the up or down buttons, press the MODE button when appears on screen. Settings include:

You can toggle between these settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. Next, toggle between On and Off status settings which occur for each above sub-menu. Example:

. and

, When the desired setting appears on screen, press the MODE button to select. The radio will save your On or Off selection for the current channel and return to standby mode. NOTE: Individual, Group and Super Group frequencies and timing are programmed by your radio communications Dealer. For quick reference, the next few pages detail the Channel Options Menu, sub-menus and their settings. Mode Option Setting Each Channel Setting System Option Setting Display Option Setting P/A mode Setting Channel Option Setting Tone Option Rx Tone Tx Tone No Tone CTCSS DCS 1 ~ 49 023 ~ 754 Invert DCS 023 ~ 754 No Tone CTCSS DCS Invert DCS 1 ~ 49 023 ~ 754 023 ~ 754 Tx Output Power High/Low Power High/Low Normal Scan List Priority Scan List Normal Scan On/Off Priority Scan On/Off 2-Tone Option Individual Tone Group Tone Super Group Tone On/Off On/Off On/Off System Option Settings Menu To enter the System Option Setting Menu, press and release the MODE button during the receive or standby mode, then use the up or down buttons until appears. Select the above option with a press and release of the MODE button.

(Beep Set, VOX (Voice Operated TX) Set, Time-Out-Timer Set, Penalty, Busy Channel Lockout Set, Marked Idle, Scan Set, Priority Scan, Transmit Delay, Power Save, Clear-To-Talk, Roger Beep, 2 tone alarm, Microphone Hook and Audio Compander). Details on sub-menu settings follow. You can toggle between these settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. If you choose the Beep Set setting, you will need to use the up or down buttons to choose or

. When the desired setting appears on screen, press the MODE button to select. The radio will save your On or Off selection and return to standby mode. If you choose the VOX Set setting, you will also need to choose between On or Off selections, by using the up or down buttons to choose, and the MODE button to select. If you choose On, you will need to choose a VOX level setting, which includes:

up or down buttons. When the desired setting appears on screen, press the MODE button. The radio will save your selection and return to standby mode. You can toggle between these VOX sensitivity level settings with the or

, If you choose the Time-Out-Timer setting, your choices include:

the settings with the up or down buttons. When the desired setting appears on screen, press the MODE button. If you choose On, you will need to choose the duration of the Time-Out-Timer setting, from 10 seconds to 990 seconds. Use the up or down buttons to toggle, until the desired number of seconds appears on the display. Use the MODE button to select. The radio will save your selection and return to standby mode. Example of display:

. Toggle between or NOTE: In the Time-Out-Timer sub-menu, if Off is selected by pressing the MODE button, the TOT function will be disabled, and the radio will return to standby mode. If you choose the Time-Out-Timer Penalty setting, your choices include Penalty On or Off. Toggle between the settings with the up or down buttons. When the desired setting appears on screen, press the MODE button. If you choose On, you will need to choose the duration of the Penalty setting, from 1 second to 100 seconds. Use the up or down buttons to toggle, then the MODE button to select the desired amount of time. The radio will save your selection and return to standby mode. Example of display:

. NOTE: In the Time-Out-Timer Penalty sub-menu, if Off is selected by pressing the MODE button, the TOT Penalty function will be disabled, and the radio will return to standby mode. NOTE: If the radio transmits in excess of the set time, it will beep an error tone and the radio will receive a signal, but will NOT transmit during the penalty time. If you choose the Busy Channel Lockout setting, your choices include:

between the settings with the up or down buttons. When the desired setting appears on screen, press the MODE button. Your radio will save your On or Off selection and return to standby mode. Toggle or NOTE: If you select On, and the channel is busy, it will inhibit transmission. If you choose the Marked Idle setting, your choices include On or Off. Toggle between the settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. The radio will save your selection and return to standby mode. Example of display:

. NOTE: If the channel is set by Busy Channel Lockout, and transmit is inhibited, Marked Idle allows a transmission when your CTCSS or DCS tone signal is received. (Scan Mode, Scan Speed, Scan Delay and Lookback). You can toggle between these settings with the up or If you choose the Scan Set setting, your choices include:

down buttons. When the desired setting appears on screen, press the MODE button to select. If you select

. (Normal Scan Transmit, Priority

, your choices will include:

Scan Transmit, Priority Select Scan and Priority Only TX Scan). You can toggle between these settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. The radio will save your selection, and return to standby mode. and and

, If you select the Scan Speed setting, you will need to choose the scan speed time, from 50 milliseconds to 500 milliseconds. Use the up or down buttons to select the desired speed, then the MODE button to select. The radio will save your selection and return to standby mode. Example of display:

. NOTE: Scan speed time is the amount of time that scan stays on a channel (when there is no signal) before moving to the next channel on the scan list. If you select the Scan Delay setting, you will need to choose the scan delay time, from 1 seconds to 30 seconds. Use the up or down buttons to select the desired time, then the MODE button to select. The radio will save your selection and return to standby mode. Example of display:

. NOTE: Scan delay time is the standby time to remain on the channel after the receiving signal stops or after transmitting. If you select the Lookback setting, you will need to choose the desired lookback frequency time, from 1 second to 10 seconds. Use the up or down buttons to select the desired time, then the MODE button to select. The radio will save your selection and return to standby mode. Example of display:

. NOTE: In Priority Scan mode, Lookback time is the interval time to check the Priority Channel when the radio receives a signal on a non-priority channel. If you choose the Priority Scan setting, your choices include Priority Scan On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. If you choose the On setting, use the up or down buttons to select your desired Priority Scan channel, then the MODE button to select. The radio will save your On or Off setting, and return to standby mode. Example of display:

. NOTE: In the Priority Scan setting mode, if the MODE or P-T-T buttons are pressed, Priority Scan will be disabled and the radio will return to standby mode. If you choose the TX Delay setting, your choices include On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. The radio will save your selection and return to standby mode. Example of display:

. NOTE: The TX Delay setting is used to remove the squelch tail from the receiving radio by creating a CTCSS turn-off

(no tone) for 180 milliseconds after TX is completed. If you choose the Clear To Talk setting, your choices include On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. The radio will save your selection and return to standby mode. Example of display:

. NOTE: If you select On, the radio issues a beep tone when pressing the P-T-T button, letting you know that speaking may begin. If you choose the Roger Beep setting, your choices include On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. The radio will save your selection and return to standby mode. An example of the Roger Beep display:

. NOTE: If you select On, the radio issues a beep tone after TX is completed to confirm the transmission has finished. If you choose the 2 Tone Alarm setting, your choices include On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. The radio will save your selection and return to standby mode. An example of the 2 Tone Alarm display:

. NOTE: If you select On, the radio issues an alarm tone after a 2 tone signal is decoded and RX carrier is no longer present if a call is received during the alarm the alarm will stop until the call is gone. Once the RX signal is no longer present the alarm will continue until the 2 tone decode is reset by pressing the AUX button for 3 seconds. If you choose the Microphone Hook setting, your choices include On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. The radio will save your selection and return to standby mode. An example of the Microphone Hook display:

. NOTE: If you select On, the Microphone hub will not require ground to activate privacy tones. If you choose the Microphone Hook setting Off, the Hook Scan setting will appear, your choices include On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. The radio will save your selection and return to standby mode. An example of the Hook Scan display:

. NOTE: If you select Microphone Hook setting Off, the Microphone hub will require ground to activate privacy tones if microphone hub is removed from ground privacy tones are defeated and the radio will operate in carrier squelch mode. If you select Hook scan On, your radio will continue to scan with the microphone hub not grounded in carrier squelch mode. If you choose the Audio Compander setting, your choices include On or Off settings. You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to select. The radio will save your selection and return to standby mode. An example of the Audio Compander display:

. NOTE: If you select On the audio quality between wide and narrow band channels will be the same. For quick reference, the next few pages detail the System Option Menu, sub-menus and their settings. System Option Setting Beep Tone VOX Option Beep On/Off VOX On/Off VOX Sensitivity Level 1 ~ Level 3 TOT On 1 ~ 990 sec Time Out Timer TOT Off TOT Penalty Penalty On 1 ~ 100 sec Penalty Off Busy Lock Busy Lock On/Off Marked Idle Marked Idle On/Off Scan Set Scan Mode Normal Scan Tx Priority Scan Tx Priority Select Scan Priority Only Tx Scan Speed Time 50 ~ 500 msec Scan Delay Time Look Back Time 1 ~ 30 sec 1 ~ 10 sec Priority Scan Tx Delay Clear To Talk Roger Beep 2-Tone Alarm Set Microphone Hook On Off On/Off On/Off On/Off On/Off Off On Audio Compander On/Off Priority Channel 1 ~ 16 Hook Off Scan Off On Display Option Settings Menu With the radio powered on, select the desired channel. Press the MODE button and then the up or down buttons until appears. Press and release the MODE button to select. Sub-menu settings include:

You can toggle between these settings with the up or down buttons. When the desired setting appears on screen, press the MODE button to select. If you select

(Name, Channel Number and Frequency). You can toggle between these settings with the up or down buttons. When the desired setting appears on the display, press the MODE button to view the current information for that setting. Example of Name display:

, your choices will include:

and

. NOTE: The Name, Channel Number and Frequency settings are display-only settings. You can not change them within these screens. If you select the Slide Setting, your choices include Slide On or Slide Off. Toggle between the settings with the up or down buttons. When the desired setting appears on screen, press the MODE button. Your radio will save your On or Off selection and return to standby mode. NOTE: If Slide Setting is On, and the radio is in standby for more than 1 minute, a slide message pre-programmed by your Dealer will scroll on screen. Display Option Setting Channel Display Format Name Character Display Channel No. Display Frequency Display Slide Set Back Light Set Slide On Slide Off Light On Light Off P/A Option Settings Menu With the radio powered on press the MODE button and then the up or down buttons until release the MODE button to select. To turn P/A mode off press the MODE button. Example of P/A display:

ACC-733 DTMF Microphone Operation appears. Press and The ACC-733 can be used for telephone interconnect or other DTMF applications. Consult your Dealer for other application possibilities. The ACC-733 can be operated in an auto dial mode or manually operated and is back lighted for low light conditions. A telephone ringer will be heard when a telephone connection has been established or for an incoming call. Auto Dial Operation Up to 16 digits can be dialed when using auto dial. Follow these steps to place a call using auto dial. A. Enter the desired number by pressing and releasing 0 9, * or # keys. The dialed numbers will appear in your radio display. # will be indicated as F in your display. Note: The # key is normally used to end, or hang up, an interconnect system. Consult your Dealer for exact system operation. The * key will be indicated as E. B. Press the SND key to send the dialed number. C. D. When the conversation has ended Press and hold the P-T-T of the microphone press and hold the # key for 1 or 2 When the called party answers, press the P-T-T of the microphone to answer. Release the P-T-T to listen for a response. seconds to end the call. Release the P-T-T when the call has ended. Manual Dial Operation A. Press and hold the P-T-T of the microphone and enter the desired number by pressing and releasing 0 9, * or # keys. The dialed numbers will appear in your radio display. # will be indicated as F in your display. Note: The # key is normally used to end, or hang up, an interconnect system. Consult your Dealer for exact system operation. The * key will be indicated as E. B. When dialing is complete release the P-T-T and wait for the called party to answer. C. D. When the conversation has ended Press and hold the P-T-T of the microphone press and hold the # key for 1 or 2 When the called party answers, press the P-T-T of the microphone to answer. Release the P-T-T to listen for a response. seconds to end the call. Release the P-T-T when the call has ended. To Store a Number in Memory A. Dial the desired number. Entered number will show in the radio display. B. Press and release the STR key. C. Press and release any number 0 9, * and # to store the number. To Recall a Stored number from Memory A. Press and release the RCL key. B. Press and release the number key from which a number has been stored. C. Press SND to dial the recalled number. If a number has been accidentally recalled repeat steps A. and B. until the proper number has been recalled. Clearing a Stored Number A. Press and release the RCL key. B. Press and release the number key from which a number has been stored. The stored number will show in the radio display. C. Press and hold the CLR key to remove the stored number. A new number can now be entered and stored in that location. Clearing a Dialed Number When a number has been accidentally entered during auto dial a press and release of the CLR key will delete an individual number. A press and hold of the CLR key will clear the entire dialed number. Licensing and Service Information FCC Licensing The Federal Communications Commission requires the operator of this radio be properly licensed under the applicable Part and/or Parts of the FCC Rules and Regulations. Consult your radio communications Dealer or contact the nearest FCC field office for information about obtaining a license. Service Do not tamper with internal adjustments. Damage to the equipment and/or improper operation may result. There are no serviceable components inside the radio. It is recommended that you return your radio to a qualified radio communications Dealer for any service or repairs. Maintenance Your Legacy radio is designed to be maintenance free. To keep it in good working condition:

Clean external surfaces with a clean cloth dampened in a solution of dishwasher detergent diluted in water. Apply the solution sparingly to avoid any moisture leaking into cracks and crevices. DO NOT submerge the radio. Use a non-

metallic brush, if necessary, to dislodge stubborn particles. Dry the surface thoroughly with a soft, lint free cloth. DO NOT use solvents or spirits for cleaning they may permanently damage the housing. Software Copyrights, Warranty Statement Software Copyrights The Topaz3 / Legacy products described in these operating instructions may include copyrighted Topaz3 / Legacy software programs stored in semi-conductor memories or other media. Laws in the United States and other countries preserve for Topaz3 / Legacy certain exclusive rights for copyrighted software programs, including the exclusive right to copy or reproduce in any form the copyrighted software program. Accordingly, the copyrighted Topaz3 / Legacy software programs contained in the Topaz3 / Legacy product(s) described in this operating instruction manual may not be copied or reproduced without the express written permission of Topaz3, LLC. Furthermore, the purchase of Topaz3 / Legacy products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Topaz3, LLC, except for normal non-

exclusive, royalty-free license to use that arises by operation of law in the sale of a product. Topaz3 / Legacy Product Warranty Topaz3, LLC (hereinafter, Topaz3) warrants that the Products and included accessories sold herein will be free from defects in workmanship or materials under normal use and service for a period of two (2) years (one year for accessories) from the date of purchase by the original end user, provided that the buyer has complied with the requirements stated herein. This warranty is offered to the initial end user and is not assignable or transferable. Topaz3 is not responsible for any ancillary equipment which is attached to or used in conjunction with Topaz3 / Legacy products. If the Product fails to function under normal use because of manufacturing defect(s) or workmanship during the two (2) years period following the date of purchase, it will be replaced or repaired at Topaz3's option at no charge when returned to the place of purchase. The defective unit must be accompanied by proof of the date of purchase in the form of a sales receipt. The sole obligation of Topaz3 hereunder shall be to replace or repair the Product covered in this Warranty. Replacement, at Topaz3's option, may include a similar or higher-featured product. Repair may include the replacement of parts or boards with functionally equivalent reconditioned or new parts or boards. Replaced parts, accessories, batteries, or boards are warranted for the balance of the original time period. All replaced parts, accessories, batteries or boards become the property of Topaz3. Topaz3 shall have no obligation to make repairs or to cause replacement required through normal wear and tear or necessitated in whole or in part by catastrophe, fault or negligence of the user, improper or unauthorized alterations or repairs to the Product, use of the Product in a manner for which it was not designed, or by causes external to the Product. This warranty is void if the serial number is altered, defaced or removed. The user is responsible for the payment of any charges or expenses incurred for the removal of the defective product from the vehicle or site of its use, for the transportation of the product to the place of repair, for the return of the repaired / replaced product to the site of its use and for the reinstallation of the product. THE EXPRESS WARRANTIES CONTAINED HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FOR ANY PRODUCT WHICH DOES NOT COMPLY WITH THE WARRANTY SPECIFIED, THE SOLE REMEDY WILL BE REPAIR OR REPLACEMENT. IN NO EVENT WILL TOPAZ3 BE LIABLE TO THE BUYER OR ITS CUSTOMERS FOR ANY DAMAGES, INCLUDING ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, OR FOR THE LOSS OF PROFIT, REVENUE OR DATA ARISING OUT OF THE USE OF OR THE INABILITY TO USE THE PRODUCT. This warranty is void for sales and deliveries outside of the U. S. A. Topaz3, LLC 10828 NW Air World Drive Kansas City, Missouri 64153 www.topaz3.com Toll free: 800-821-7848 Phone: 816-891-6320 Fax: 816-891-8815 Printed in Korea P/N: 680-090-xxxx