Compliance Information FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. Any modifications to this product may violate the rules of the Federal Communications Commission and make operation of the product unlawful. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference recieved, including interference that may cause undesired operation. Declaration of Conformity Quality Assurance Manager Don Carr Midmark Corporation 60 Vista Drive P.O. Box 286 Versailles, OH 45380 U.S.A. Midmark Corporation declares that 9A429001 thru 9A429005 conform to the applicable requirements of the Radio Equipment & Telecommunications Equipment Directive 1999/5/EC, Annex II Serial Number: ALL Date: 10/13/2011 077-0880-00 Limited Warranty General Information Intended Use This product is intended to control patient positioning while providing better patient access by eliminating the cord from the controller(s). Authorized CE Representative Countries in the EEC should direct all questions, inci-
dents, and complaints to Midmarks authorized CE Representative listed below:
Calling for Service If service is required, contact your Midmark dealer. To contact Midmark directly:
1-800-MIDMARK (1-800-643-6275) Monday-Friday 8:00 am until 5:00 pm (EST) www.midmark.com Midmark Europe SAS 22, Rue de St. Denis 53500 Ernee, FRANCE Phone: 33-2-430-517-76 Fax: 33-2-430-569-10 SCOPE OF WARRANTY Midmark Corporation (Midmark) warrants to the original purchaser its new Alternate Care products and components
(except for components not warranted under Exclusions) manufactured by Midmark to be free from defects in material and workmanship under normal use and service. Midmarks obligation under this warranty is limited to the repair or replace-
ment, at Midmarks option, of the parts or the products the defects of which are reported to Midmark within the applicable warranty period and which, upon examination by Midmark, prove to be defective. APPLICABLE WARRANTY PERIOD The applicable warranty period, measured from the date of delivery to the original user, shall be one (1) year for all warranted products and components. EXCLUSIONS This warranty does not cover and Midmark shall not be liable for the following: (1) repairs and replacements because of misuse, abuse, negligence, alteration, accident, freight damage, or tampering; (2) products which are not installed, used, and proper-
ly cleaned as required in the Midmark Installation and or Instal-
lation / Operation Manual for this applicable product. (3) products considered to be of a consumable nature; (4) accessories or parts not manufactured by Midmark; (5) charges by anyone for adjustments, repairs, replacement parts, installation, or other work performed upon or in connection with such products which is not expressly authorized in writing in advance by Midmark. EXCLUSIVE REMEDY Midmarks only obligation under this warranty is the repair or replacement of defective parts. Midmark shall not be liable for any direct, special, indirect, incidental, exemplary, or consequential damages or delay, including, but not limited to, damages for loss of profits or loss of use. NO AUTHORIZATION No person or firm is authorized to create for Midmark any other obligation or liability in connection with the products. THIS WARRANTY IS MIDMARKS ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY WARRANTIES OF MERCHANT-
ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS. Midmark Corporation 60 Vista Drive Versailles, OH 45380-0286 Phone: 937-526-3662 Fax: 937-526-5542 www.midmark.com Users Guide 625 Wireless Controls 9A429 This guide outlines basic operation of the wireless hand / foot control and the associated base station. If service is required, contact your authorized Midmark dealer. Dealer (name / phone):
__________________________________ __________________________________ __________________________________ __________________________________ Date of Purchase: __________________ Midmark Corporation 2009 003-1945-00 Rev. B Compliance Information - continued... IC Compliance Statement Interference This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR Industrie Canada applicables aux appareils radio exempts de licence. exploitation est autorise aux deux conditions suivantes: (1) appareil ne doit pas produire de brouillage, et (2) utilisateur de appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible en compromettre le fonctionnement. Antennas Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that neccessary for successful communication. Conformment la rglementation Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne un type et un gain maximal (ou infrieur) approuv pour metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique intention des autres utilisateurs, il faut choisir le type antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas intensit ncessaire tablissement une communication satisfaisante. Association Procedure The wireless controller will only function with the chair it has been associated with. This prevents unwanted movement in locations with more than one chair. Each wireless controllers association is preset at the factory. This procedure is only required in the event of a malfunction, if a new controller is purchased, or if you are attempting to use the controller with a chair other than the one it was originally associated with. on the wireless controller, until you hear three beeps. Association Procedure:
A) Disconnect power to the table for at least 3 seconds. B*) Reconnect power, then press & hold the Stop & Home buttons
* Note: Step B must be performed within 10 seconds of Step A. C) Check for proper operation of wireless controller. D) If associating a hand and foot control, repeat procedure using the other wireless controller. Home Stop Home Stop Specifications Range of Operation ............. 20 ft. (6 m) radius Batteries:
Hand Control .................................AA (qty. 2) Foot Control ..................................AA (qty. 2) MA771100i Troubleshooting Low battery When any control button is pressed, that controller sounds a single beep. (All functions operate) Cause:
Solution: Replace batteries When any control button is pressed, nothing happens. (No beeps, no movement, etc.) Cause:
Solution: 1. Replace batteries The wireless controllers will only function with the ... chair they have been associated with. This prevents unwanted movement in locations with more than one chair. 1. Batteries completely dead 2. Wireless controller has lost association to chair 2. Perform Association Procedure*
If further service is required, contact your authorized Midmark dealer.