FCC ID: SSVNAEPI03 EPI7684, radio module for wireless food probe system

2022-03-18 Manual for EPI7684, the wireless food probe system 1 General The wireless food probe system consists of the radio module (EPI7684), antenna system and the wireless food probe. This system enables the roasting process of the food to be monitored simple and reliably. The wireless food probe will be here not described because it is a passive device and does not matter for the installation of the system. The wireless food probe system may be installed in the Miele domestic appliances like ovens or steam cooker (host devices) Integration instruction The EPI7684 and the loop antenna must be integrated under consideration of the technical data. It is not allowed to make any changes on the module or use another antenna. 2 Technical data EPI7684 and antenna VCC in V Current in mA Ambient temperature in C Humidity max Dimensions in mm Wireless Antenna type Antenna gain Frequency band Method of transmitting radio signal Channels Transmission Power in mW 13,0 and 3,3 DC 170 max. 0-85 90%

Non condensation 105x80 external loop antenna

-7dBi 2400 MHz - 2483.5 MHz FHSS 600

<100 Interface to the control-/ power electronic of the host device 2.1 On the control-/ power electronic is a 4-pin rast 2.5 plug and on the EPI site is 8-pin rast 2.5 plug. This connection includes communication and power supply wire (13 and 3,3V DC) 2022-03-18 3 Norms / Standards 3.1 FCC / IC FCC regulation:

IC regulation:

FCC 47 CFR Part 15.247 Part 1.1310 Part 1.1091 RSS-247, Issue 2 RSS-Gen, Issue 5 RSS-102, Issue 5 3.2 Photos and Labels Antenna connector Picture 1: Module EPI7684 2022-03-18 Picture 2: label of the module Picture 3: loop antenna, FAKRA-connector 4 Compliance Statement and Integration In accordance with FCC 47 CFR Part 15 and RSS-247, Issue 2, the EPI7684 (FCC ID: SSVNAEPI03;

IC: 5669B-EPINA03) is listed as a Modular Transmitter Device. Notice:

This device complies with Part 15 of the FCC Rules and contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS Standarrd(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 2022-03-18 Radiofrequency radiation exposure Information:

This equipment complies with FCC radiation exposure limits set forth and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CAUTION:

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. USERS MANUAL OF THE END PRODUCT:

The end user has to be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. The following statements are required to be available in the users manual:

This device complies with Part 15 of the FCC Rules and contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS Standarrd(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Radiofrequency radiation exposure Information:

This equipment complies with FCC radiation exposure limits set forth and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites d'exposition aux rayonnements de la FCC et aux limites d'exposition aux rayonnements du Canada tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet metteur ne doit pas tre co-localis ou fonctionner en conjonction avec une autre antenne ou un autre metteur. LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following Contains FCC ID: SSVNAEPI03;

Contains IC: 5669B-EPINA03". The following statement has to also be available on the label:

This device complies with Part 15 of the FCC Rules and contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS Standarrd(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 2022-03-18 Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Integration 4.1 This EPI7684 Module will only be integrated on our responsibility into Miele appliances/endproducts. The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with the Part 15 Subpart B requirements, the host manufacturer is required to show compliance with the Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the modules intentional emissions are compliant (i.e. fundamental and out of band emissions) with the Radio essential requirements. The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in the Part 15 Subpart B or emissions are complaint with the Radio aspect

promicron [-%

wireless solutions EP1I/684 MN: 12187550 SN: 0000180-18-39 22/02 GR:

FCC-ID: SSVNAEPIO3 1C-ID: 5669B-NAEPIO3EK

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 2022-03-18 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID SSVNAEPI03 Model name EPI7684 For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram and Schematics Information. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name: Mr. Simon Floren Company: Miele & Cie. KG Address: Carl-Miele-Platz 1, 59302 Oelde, Germany Phone: +49524591-4101 Fax: +49524591-784101 Email: simon.floren@miele.com