Cloud Router Switch 8 Ethernet port series Setup Guide and Warranty Information The CRS is a highly configurable switch, powered by RouterOS. These models currently available in the 8 Ethernet port series:
CloudRouterSwitch 109-8G-1S-2HnD-IN
(8 Ethernet ports, one SFP port, built in 2GHz wireless AP) CloudRouterSwitch 112-8G-4S-IN
(8 Ethernet ports, four SFP ports) First use The device comes preinstalled with RouterOS and is ready to use. Device is compatible with RouterOS v6 and newer, if your device comes preinstalled with an earlier version, please upgrade before using it. CRS112-8G-4S-IN:
all the ports are switched. CRS109-8G-1S-2HnD-IN:
ports 2-8 are switched, wireless interface and switch are bridged, and bridge contains a DHCP server. Eth1 and SFP1 have DHCP client configured. Both models can be accessed though the IP 192.168.88.1, username is admin and there is no password. Please connect with your web browser to this IP address to configure it. See this page for connection and configuration guides:
http://wiki.mikrotik.com/wiki/Category:Manual Powering The device accepts powering in the following ways:
Direct-input power jack:
8-56V
(24V 0.8A PSU included) Passive PoE input:
8-56V
(injector included) Extension Slots and Ports Eight
(8) 10/100/1000
(Gigabit) Ethernet ports
(Auto MDI/X) For CRS109:
One SFP cage, compatible with 1.25G SFP modules For CRS112:
Four SFP cages, compatible with 1.25G SFP modules Resetting the device In case you wish to return the device to its original configuration, you can use the RESET button. Hold this button during boot time until LED lights start flashing, then release the button to reset RouterOS configuration. You can use this procedure if you have forgotten the password to access the device, or simply wish to return the unit to its default configuration state. See www.routerboard.com for more information. Contact support@mikrotik.com 24/04/14 Buttons and Jumpers RouterBOOT reset button
(image Reset1) has several functions:
Hold the button before powering on the device, and at power up, the button will force load the backup boot loader. Continue holding the button for the other two functions of this button:
Release the button when green LED starts flashing, to reset RouterOS configuration. To not load backup boot loader, you can start holding the button after power is already applied Release the button after LED is no longer flashing
(~20 seconds) to cause device to look for Netinstall servers
(required for reinstalling RouterOS over network) RouterOS reset jumper hole
(image Reset2):
resets RouterOS software to defaults. Hold screwdriver pressed to this reset hole, and boot the device. Hold screwdriver in place until RouterOS configuration is cleared
(10 seconds). Operating System Support Currently tested operating system is MikroTik RouterOS
(starting from version 6). Safety Notice Electric shock hazard. This equipment is to be serviced by trained personnel only. Copyright and Warranty information Copyright MikroTikls SIA. This document contains information protected by copyright law. No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this document are the property of their respective holders. Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve
(12) months from the shipping date to be free of defects in materials and workmanship under normal use and service, except in case of damage caused by me-
chanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature. To return failed units to MikroTik, you must perform the following RMA
(Return Merchandise Authorization) procedure. Fol-
low the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. 1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regard-
ing all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik in Latvia. 2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for:
CCR1016-12G, CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200, RB600, RB600A and RB800 as a paid service
(fees apply). 3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the send-
er at sender's cost. If the customer has not organized return of such rejected devices within 12 months from the day of arrival, MikroTik has the right to discard them. RMA Instructions are located on our webpage here:
http://rma.mikrotik.com This document is provided as is without a warranty of any kind, expressed or implied, including, but not limited to, the im-
plied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the contents of this document, however, it is possible that it may contain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, conse-
quential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com 24/04/14 CE Declaration of Conformity Full Declaration of Conformity
(DoC) may be obtained by visiting this web page:
http://routerboard.com/doc/
[EN]
English
[BG]
Bulgarian
[CZ]
Czech
[DK]
Danish
[DE]
German
[EE]
Estonian
[GR]
Greek
[ES]
Spanish
[IT]
Italian
[LV]
Latvian
[LT]
Lithuanian
[HU]
Hungarian
[NL]
Dutch
[PL]
Polish
[PT]
Portuguese
[RO]
Romanian
[SK]
Slovak
[SI]
Slovenian
[FI]
Finish Hereby, MIKROTKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
, MIKROTKLS SIA
, ROUTERBOARD 1999/5/EC. MIKROTKLS SIA tmto prohlauje, e ROUTERBOARD spluje zkladn poadavky a vechna pslun ustanoveni Smrnice 1999/5/ES. Undertegnede MIKROTKLS SIA erklrer herved, at flgende udstyr ROUTERBOARD overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt MIKROTKLS SIA dass sich das Gert ROUTERBOARD in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Kesolevaga kinnitab MIKROTKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulene-
vatele teistele asjakohastele stetele. MIKROTKLS SIA ROUTERBOARD 1999/5/
Por la presente, MIKROTKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 1999/5/EC. Con la presente MIKROTKLS SIA dichiara che questo ROUTERBOARD conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o MIKROTKLS SIA deklar, ka ROUTERBOARD atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo MIKROTKLS SIA deklaruoja, kad is ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas A MIKROTKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD tpus beren-dezs teljesti az alapvet kvetelmnyeket s ms 1999/5/EK irnyelvben meghatrozott vonatkoz rendelkezseket. Hierbij verklaart MIKROTKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentile eisen en de andere relevante bepalin-gen van richtlijn 1999/5/EG. Niniejszym MIKROTKLS SIA deklaruje e ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi waciwymi postanowieniami Dyrektywy 1999/5/EC. Eu, MIKROTKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provises relevantes da Directiva 1999/5/EC. Prin prezenta, MIKROTKLS SIA declar c aparatul ROUTERBOARD este n conformitate cu cerinele eseniale i cu alte prevederi pertinente ale Directivei 1999/5/CE.. MIKROTKLS SIA tmto vyhlasuje, e ROUTERBOARD spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. MIKROTKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi doloili direktive 1999/5/ES. MIKROTKLS SIA vakuuttaa tten ett ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direk-
tiivin muiden ehtojen mukainen. Denna utrustning r i verensstmmelse med de vsentliga kraven och andra relevanta bestmmelser i direktiv 1999/5/EC. MIKROTKLS SIA Erklrer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999/5/EF.
[SE]
Swedish
[NO]
Norwegian EN. Instruction manual:
Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More information on http://wiki.mikrotik.com BG.
:
,
. 192.168.88.1
,
. http://wiki.mikrotik.com CZ. Nvod k pouit:
Pipojte napjec adaptr k zapnut pstroje. Otevete 192.168.88.1 ve webovm prohlei pro konfiguraci produktu. Vce informac najdete v http://wiki.mikrotik.com DK. Instruktionsbog:
Tilslut strmadapte-
ren for at tnde for enheden. bn 192.168.88.1 i en webbrowser til at konfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'em-
ploi:
Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informa-
tions dans http://wiki.mikrotik.com DE. Bedienungsanleitung:
Verbinden Sie das Netzteil, um das Gert einzuschalten. ffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com EE. Kasutusjuhend:
hendage toiteadapter seadme sissellitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de instrucciones:
Conecte el adaptador de alimentacin para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Ms informacin en http://wiki.mikrotik.com IT. Manuale di istruzioni:
Collegare l'adattatore di alimentazione per accendere l'unit. Aprire 192.168.88.1 in un browser Web per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com LV. Lietoanas instrukcija:
Pievienojiet Strvas adapteri, lai ieslgtu ierci. Atvrt 192.168.88.1 ar interneta prlku, lai konfigurtu produktu. Plaka informcija http://wiki.mikrotik.com LT. Naudojimosi instrukcija:
Prijunkite maitinimo adapter junkite rengin. interneto narykl 192.168.88.1 Atidarykite galite konfigruoti gamin. Daugiau informacijos rasite http://wiki.mikrotik.com HU. Hasznlati utasts:
Csatlakoztassa a hlzati adaptert a kszlk bekapcsolshoz. Megnyitsa 192.168.88.1 egy webbngszben belltani a termket. Tbb informci http://wiki.mikrotik.com NL. Handleiding:
Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrow-
ser om het product te configureren. Meer informatie in http://wiki.mikrotik.com PL. Instrukcja obsugi:
Podcz adapter zasilania, aby wczy urzdzenie. Otwrz 192.168.88.1 w przegldarce internetowej, aby skonfigurowa urzdzenie. Wicej informacji w http://wiki.mikrotik.com PT. Manual de instrues:
Conecte o adaptador de alimentao para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informaes em http://wiki.mikrotik.com RO. Instruciuni de utilizare
:
Conectai adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 ntr-un browser web pentru a configura produsul. Mai multe informaii n http://wiki.mikrotik.com SK. Nvod na pouitie:
Pripojte napjac adaptr k zapnutiu prstroja. Otvorte 192.168.88.1 vo webovom prehliadai pre konfigurciu produktu. Viac informci njdete v http://wiki.mikrotik.com SI. Navodila:
Prikljuite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Ve informacij v http://wiki.mikrotik.com FI. Kyttohje:
Kytke virtalhde plle laitteen. Avaa 192.168.88.1 in selaimen mritt tuotteen. Lis tietoa http://wiki.mikrotik.com SE. Instruktionsmanual:
Anslut ntadap-
tern fr att sl p enheten. ppna 192.168.88.1 i en webblsare fr att konfigurera produkten. Mer information p http://wiki.mikrotik.com NO. Bruksan-
visningen:
Koble strmadapteren for sl p enheten. pne 192.168.88.1 i en nettleser for konfigurere produktet. Mer informasjon p http://wiki.mikrotik.com GR.
:
. 192.168.88.1 Web
. http://wiki.mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com 24/04/14 Federal Communication Commission Interference Statement
(FCC ID:TV7CRS109-8G2HND) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT: FCC RF Exposure requirements. 25 cm minimum distance has to be maintained between the antenna and user. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. See www.routerboard.com for more information. Contact support@mikrotik.com 15:50:42