RouterBOARD Metal 9HPN Quick Setup Guide and Warranty Information The RouterBOARD Metal 9HPN is a solid, waterproof outdoor device with a high power wireless transmitter (900MHz, 802.11b/g/n, N-Male antenna connector), and one 10/100 Ethernet connector which supports MDI-X auto detection. The device is packaged with a 24V power adapter, a PoE injector and two mounting loops. First use so 1. Connect the antenna to the N-Male connector 2. Use the latches to open the product case, to reveal the Ethernet connector 3. Use the provided round rubber insulator to put on the Ethernet cable, and push it into the case opening, To put the cable though the insulator, you have to put in the cable first, and only then clamp on the Ethernet connector. If the connector is already on the cable, you can cut the insulator on one side, to clamp it around the cable, but this sacrifices waterproofness. The Metal accepts 12-28V Passive PoE from a PoE injector (please compensate voltage for loss due to cable length) The default IP address from Ether1 is 192.168.88.1 for configuration Username is admin and there is no password the opening tightly closed. that 4. 5. is 6. Depending on the antenna used, you must set its gain in the RouterOS software to ensure that EIRP meets the limit set by authorities. This is done in the Wireless menu. Powering The board accepts powering from the Ethernet port (Passive PoE):
Ethernet port accepts passive Power over Ethernet 12-28V DC. Package contains a 24V adapter and a PoE injector. Maximum power consumption of the device is 12W at 24V. Booting process Connect to wireless SSID MikroTik and open 192.168.88.1 in your web browser. Username is admin and there is no password. In case IP connection is not available, Winbox can be used to connect information here:
http://wiki.mikrotik.com/wiki/First_time_startup the MAC address of the device. More to In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when starting it until the LED light turns off, and Metal will start to look for Netinstall servers. Mounting To tighten the Metal to a pole, use the provided mounting loops. The Metal comes bundled with two plastic and two metallic mounting loops (choose either) - guide the loops around the Metal though the provided edge markings, and around the pole where it will be mounted. You should avoid connecting a loose Ethernet cable to the Ethernet port - secure the cable to a wall or the pole, so that the cable weight is not pulling the port. It is recommended to secure the Ethernet cable less than 2m from the Metal device. This is to ensure that the cable doesn't damage the port by its weight, or doesn't fall out. Expansion Slots and Ports Built in 900MHz 802.11b/g/n wireless, 1x1 MIMO, station mode (AP mode for Metal A-2SHPN) One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cable for connecting to other network devices. The Ethernet port accepts 8-30V DC powering from a passive PoE injector. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14 Buttons and Jumpers RouterOS reset jumper hole (no direct access, board has to be removed from case) resets RouterOS software to defaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place until RouterOS configuration is cleared. RouterBOOT reset button (access through the door) has two functions:
o o Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (same result as with reset hole) Hold this button during boot time longer, until LED turns off, then release it to make the device look for Netinstall servers. Operating System Support Currently tested operating system is MikroTik RouterOS (starting from version v5.16). Copyright and Trademarks Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are the property of their respective holders. Hardware. MikroTik warrants all RouterBOARD series equipment for the term of one year from the shipping date to be free of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature. To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. 1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik in Latvia. 2. We do not offer repairs for products that are not covered by warranty. Exceptions can be made for RB1000, RB1100 and RB1200. 3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotikls will be returned to the sender at sender's cost. RMA Instructions are located on our webpage here: http://rma.mikrotik.com Manual. This manual is provided as is without a warranty of any kind, expressed or implied, including, but not limited to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14 Federal Communication Commission Interference Statement
(FCC ID: TV7METL9HPN) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT: Exposure to Radio Frequency Radiation. 63 cm minimum distance has to be maintained between the antenna and the occupational user and 142 cm to general public. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Approved antenna:
Yagi antenna, Model RFY-0900-17B, 17 dBi Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14 CE Declaration of Conformity Full Declaration of Conformity (DoC) may be obtained by visiting this web page:
http://routerboard.com/doc/
[EN] English Hereby, MIKROTKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
[BG] Bulgarian , MIKROTKLS SIA , ROUTERBOARD
[CZ] Czech
[DK] Danish
[DE] German
[EE] Estonian
[GR] Greek
[ES] Spanish
[IT] Italian
[LV] Latvian
[LT] Lithuanian 1999/5/EC. MIKROTKLS SIA tmto prohlauje, e ROUTERBOARD spluje zkladn poadavky a vechna pslun ustanoveni Smrnice 1999/5/ES. Undertegnede MIKROTKLS SIA erklrer herved, at flgende udstyr ROUTERBOARD overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt MIKROTKLS SIA dass sich das Gert ROUTERBOARD in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Kesolevaga kinnitab MIKROTKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. MIKROTKLS SIA ROUTERBOARD 1999/5/
Por la presente, MIKROTKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 1999/5/EC. Con la presente MIKROTKLS SIA dichiara che questo ROUTERBOARD conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o MIKROTKLS SIA deklar, ka ROUTERBOARD atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo MIKROTKLS SIA deklaruoja, kad is ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas
[NL] Dutch
[PL] Polish
[HU] Hungarian A MIKROTKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD tpus beren-dezs teljesti az alapvet kvetelmnyeket s ms 1999/5/EK irnyelvben meghatrozott vonatkoz rendelkezseket. Hierbij verklaart MIKROTKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentile eisen en de andere relevante bepalin-gen van richtlijn 1999/5/EG. Niniejszym MIKROTKLS SIA deklaruje e ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi waciwymi postanowieniami Dyrektywy 1999/5/EC.
[PT] Portuguese Eu, MIKROTKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provises relevantes
[SK] Slovak
[RO] Romanian Prin prezenta, MIKROTKLS SIA declar c aparatul ROUTERBOARD este n conformitate cu cerinele eseniale i cu alte prevederi pertinente ale Directivei 1999/5/CE.. MIKROTKLS SIA tmto vyhlasuje, e ROUTERBOARD spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES.
[SI] Slovenian MIKROTKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi doloili direktive 1999/5/ES. MIKROTKLS SIA vakuuttaa tten ett ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Denna utrustning r i verensstmmelse med de vsentliga kraven och andra relevanta bestmmelser i direktiv 1999/5/EC.
[NO] Norwegian MIKROTKLS SIA Erklrer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og vrige relevante
[FI] Finish
[SE] Swedish da Directiva 1999/5/EC. krav i direktiv 1999/5/EF. BG. : , . 192.168.88.1 CZ. Nvod k pouit: Pipojte napjec
, . http://wiki.mikrotik.com adaptr k zapnut pstroje. Otevete 192.168.88.1 ve webovm prohlei pro konfiguraci produktu. Vce informac najdete v DK. Instruktionsbog: Tilslut strmadapteren for at tnde for enheden. bn 192.168.88.1 i en http://wiki.mikrotik.com webbrowser til at konfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gert Plus d'informations dans http://wiki.mikrotik.com einzuschalten. ffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im EE. Kasutusjuhend: hendage toiteadapter seadme sissellitamiseks. Avatud 192.168.88.1 in http://wiki.mikrotik.com ES. Manual de instrucciones: Conecte el veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com adaptador de alimentacin para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Ms IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unit. Aprire 192.168.88.1 in un browser LV. Lietoanas instrukcija: Pievienojiet Web per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com Strvas adapteri, lai ieslgtu ierci. Atvrt 192.168.88.1 ar interneta prlku, lai konfigurtu produktu. Plaka informcija LT. Naudojimosi instrukcija: Prijunkite maitinimo adapter junkite rengin. interneto narykl http://wiki.mikrotik.com HU. Hasznlati 192.168.88.1 Atidarykite galite konfigruoti gamin. Daugiau informacijos rasite http://wiki.mikrotik.com utasts: Csatlakoztassa a hlzati adaptert a kszlk bekapcsolshoz. Megnyitsa 192.168.88.1 egy webbngszben NL. Handleiding: Sluit voedingsadapter aan op het apparaat belltani a termket. Tbb informci http://wiki.mikrotik.com in te schakelen. Open 192.168.88.1 in een webbrowser om het product te configureren. Meer informatie in PL. Instrukcja obsugi: Podcz adapter zasilania, aby wczy urzdzenie. Otwrz 192.168.88.1 w http://wiki.mikrotik.com http://wiki.mikrotik.com informacin en See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14 PT. Manual de przegldarce internetowej, aby skonfigurowa urzdzenie. Wicej informacji w http://wiki.mikrotik.com instrues: Conecte o adaptador de alimentao para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para
: Conecta i adaptorul de configurar o produto. Mais informaes em http://wiki.mikrotik.com RO. Instruc iuni de utilizare alimentare pentru a porni aparatul. Deschide 192.168.88.1 ntr-un browser web pentru a configura produsul. Mai multe informa ii n http://wiki.mikrotik.com SK. Nvod na pouitie: Pripojte napjac adaptr k zapnutiu prstroja. Otvorte SI. 192.168.88.1 vo webovom prehliadai pre konfigurciu produktu. Viac informci njdete v http://wiki.mikrotik.com Navodila: Prikljuite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Ve FI. Kyttohje: Kytke virtalhde plle laitteen. Avaa 192.168.88.1 in selaimen informacij v http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut ntadaptern fr att sl p mritt tuotteen. Lis tietoa http://wiki.mikrotik.com enheten. ppna 192.168.88.1 i en webblsare fr att konfigurera produkten. Mer information p http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strmadapteren for sl p enheten. pne 192.168.88.1 i en nettleser for konfigurere GR. :
produktet. Mer informasjon p http://wiki.mikrotik.com
. 192.168.88.1 Web
. http://wiki.mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 3-Apr-14