mANTBox series The mANTBox is a solid and waterproof outdoor device based on the RB911 wireless router series. It has high power 802.11b/g/n wireless, and one Gigabit Ethernet connector, which supports MDI-X auto detection. The device has a built in Sectoral antenna. The device is packaged with a 24V power adapter, a PoE injector and a mounting kit. First use 1. Unscrew the lid screw by hand, or with a hex screwdriver. 2. 3. The device accepts 10-28V Passive PoE from a PoE injector (please compensate voltage for loss due to cable length) or from the power jack The default IP address from Ether1 is 192.168.88.1 for configuration Username is admin and there is no password Powering The device comes included with a 24V 0.8A power adapter. It can be used with the included PoE injector, or the power jack. Device accepts 8-30V for both methods. Maximum power consumption of the device is 11W at 24V. Please use the PoE injector with the DATA+POWER end connected to the mANTBox unit, and DATA end to your switch or PC. Booting process Connect to wireless SSID MikroTik and open 192.168.88.1 in your web browser. Username is admin and there is no password. In case IP connection is not available, Winbox can be used to connect to the MAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when starting it until the LED light turns off, and the device will start to look for Netinstall servers. Mounting The mANTbox 12s comes with a QuickMount adapter that can be attached to a wall using the included screws, or attached to a pole, using the included metal mounting ring. The QuickMount allows the device to be adjusted horizontally and vertically. The mANTbox 12s comes with metal pole brackets, that clamp around metal poles. More detailed instructions for assembly are available on http://routerboard.com Please avoid connecting a loose Ethernet cable to the Ethernet port - secure the cable to a wall or the pole, so that the cable weight is not pulling the port. It is recommended to secure the Ethernet cable less than 2m from the device. This is to ensure that the cable doesn't damage the port by its weight, or doesn't fall out. It is possible to connect a grounding wire to the device, by opening the lid, a grounding screw is provided there. Expansion Slots and Ports Built in 2,4GHz, 802.11b/g/n wireless, 2x2 MIMO, AP/staton/bridge modes supported One 10/100/1000 Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or crossover cable for connecting to other network devices. The Ethernet port accepts 10-28V DC powering from a passive PoE injector. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 19-Jun-18 Buttons and Jumpers The reset button is located behind the case door, to the left of the ETH port. It has following functions:
Loading the backup RouterBOOT loader: Hold this button before applying power, release after three seconds since powering, to load backup Boot loader. This might be necessary if the device is not operation because of a failed RouterBOOT upgrade. When you have started the device with the backup loader, you can either set RouterOS to force backup loader in the RouterBOARD settings, or have a chance to reinstall the failed RouterBOOT from a fwf file
(total 3 seconds) Resetting the RouterOS configuration: If you keep holding this button for 2 more seconds until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds) Enabling CAPs mode: To connect this device to a wireless network managed by CAPsMAN, keep holding the button for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds) Starting the RouterBOARD in Netinstall mode: Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD look for Netinstall servers. You can also simply keep the button pressed until the device shows up in the Netinstall program on Windows (total 15 seconds) Operating System Support Currently tested operating system is MikroTik RouterOS (starting from version v6.24). Copyright and Warranty information Copyright MikroTikls SIA. This document contains information protected by copyright law. No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this document are the property of their respective holders. Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from the shipping date to be free of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature. To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. 1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik in Latvia. 2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for: CCR1016-12G, CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200, RB600, RB600A and RB800 as a paid service (fees apply). Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the sender at 3. sender's cost. If the customer has not organized return of such rejected devices within 12 months from the day of arrival, MikroTik has the right to discard them. RMA Instructions are located on our webpage here: http://rma.mikrotik.com This document is provided as is without a warranty of any kind, expressed or implied, including, but not limited to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the contents of this document, however, it is possible that it may contain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 19-Jun-18 Federal Communication Commission Interference Statement FCC ID: TV7RB911G-2HPND This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT: Exposure to Radio Frequency Radiation. 20 cm minimum distance has to be maintained between the antenna and the occupational user and 20 cm to general public. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. List of additional approved antennas:
Sectoral 120 degree antenna, 12dBi Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. Industry Canada (IC:7442A-911G2HPND) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 19-Jun-18 CE Declaration of Conformity Full Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/
Manufacturer: Mikrotikls SIA, Pernavas street 46, Riga, Latvia, LV1009. Maximum Output Power (EIRP) in the frequency range 2412-2472 MHz is 20 dBm.
[EN] English
[BG] Bulgarian
[CZ] Czech
[DK] Danish
[DE] German
[EE] Estonian
[GR] Greek
[ES] Spanish
[IT] Italian Hereby, MIKROTKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/eu.
, MIKROTKLS SIA , ROUTERBOARD 2014/53/eu. MIKROTKLS SIA tmto prohlauje, e ROUTERBOARD spluje zkladn poadavky a vechna pslun ustanoveni Smrnice 2014/53/eu. Undertegnede MIKROTKLS SIA erklrer herved, at flgende udstyr ROUTERBOARD overholder de vsentlige krav og vrige relevante krav i direktiv 2014/53/eu. Hiermit erklrt MIKROTKLS SIA dass sich das Gert ROUTERBOARD in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 2014/53/EG befindet. Kesolevaga kinnitab MIKROTKLS SIA seadme ROUTERBOARD vastavust direktiivi 2014/53/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. MIKROTKLS SIA ROUTERBOARD 2014/53/
Por la presente, MIKROTKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 2014/53/EC. Con la presente MIKROTKLS SIA dichiara che questo ROUTERBOARD conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva2014/53 /CE. Ar o MIKROTKLS SIA deklar, ka ROUTERBOARD atbilst Direktvas2014/53 /EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo MIKROTKLS SIA deklaruoja, kad is ROUTERBOARD atitinka esminius reikalavimus ir kitas 2014/53/EB Direktyvos nuostatas
[LV] Latvian
[LT] Lithuanian
[HU] Hungarian A MIKROTKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD tpus beren-dezs teljesti az alapvet kvetelmnyeket s ms 2014/53/EK
[NL] Dutch
[PL] Polish irnyelvben meghatrozott vonatkoz rendelkezseket. Hierbij verklaart MIKROTKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentile eisen en de andere relevante bepalin-gen van richtlijn2014/53 /EG. Niniejszym MIKROTKLS SIA deklaruje e ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi waciwymi postanowieniami Dyrektywy 2014/53/EC.
[PT] Portuguese Eu, MIKROTKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provises relevantes da Directiva 2014/53/EC.
[RO] Romanian Prin prezenta, MIKROTKLS SIA declar c aparatul ROUTERBOARD este n conformitate cu cerinele eseniale i cu alte prevederi pertinente ale Directivei 2014/53/CE..
[SK] Slovak MIKROTKLS SIA tmto vyhlasuje, e ROUTERBOARD spa zkladn poiadavky a vetky prslun ustanovenia Smernice 2014/53/ES.
[SI] Slovenian MIKROTKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi doloili direktive 2014/53/ES.
[FI] Finish MIKROTKLS SIA vakuuttaa tten ett ROUTERBOARD tyyppinen laite on direktiivin 2014/53/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hrmed intygar MIKROTKLS SIA att denna RouterBOARD r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 2014/53/EG.
[SE] Swedish
[NO] Norwegian MIKROTKLS SIA Erklrer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/EF. DK. Instruktionsbog: Tilslut strmadapteren for at tnde for enheden. bn 192.168.88.1 i en webbrowser til at konfigurere produktet. Mere DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gert einzuschalten. ffnen Sie 192.168.88.1 EE. Kasutusjuhend: hendage toiteadapter seadme sissellitamiseks. EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More information on http://wiki.mikrotik.com BG. : , . 192.168.88.1 , . CZ. Nvod k pouit: Pipojte napjec adaptr k zapnut pstroje. Otevete 192.168.88.1 ve webovm prohlei pro konfiguraci produktu. Vce informac http://wiki.mikrotik.com najdete v http://wiki.mikrotik.com information i http://wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://wiki.mikrotik.com in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Ms informacin en http://wiki.mikrotik.com l'adattatore di alimentazione per accendere l'unit. Aprire 192.168.88.1 in un browser Web per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com Lietoanas instrukcija: Pievienojiet Strvas adapteri, lai ieslgtu ierci. Atvrt 192.168.88.1 ar interneta prlku, lai konfigurtu produktu. Plaka informcija http://wiki.mikrotik.com Daugiau informacijos rasite http://wiki.mikrotik.com webbngszben belltani a termket. Tbb informci http://wiki.mikrotik.com in een webbrowser om het product te configureren. Meer informatie in http://wiki.mikrotik.com 192.168.88.1 w przegldarce internetowej, aby skonfigurowa urzdzenie. Wicej informacji w http://wiki.mikrotik.com alimentao para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informaes em http://wiki.mikrotik.com RO. Instruciuni de utilizare : Conectai adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 ntr-un browser web pentru a configura produsul. Mai multe informaii n http://wiki.mikrotik.com informci njdete v http://wiki.mikrotik.com http://wiki.mikrotik.com Instruktionsmanual: Anslut ntadaptern fr att sl p enheten. ppna 192.168.88.1 i en webblsare fr att konfigurera produkten. Mer information p http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strmadapteren for sl p enheten. pne 192.168.88.1 i en nettleser for konfigurere produktet. Mer informasjon p http://wiki.mikrotik.com
: . 192.168.88.1 Web
. http://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapter junkite rengin. interneto narykl 192.168.88.1 Atidarykite galite konfigruoti gamin. HU. Hasznlati utasts: Csatlakoztassa a hlzati adaptert a kszlk bekapcsolshoz. Megnyitsa 192.168.88.1 egy ES. Manual de instrucciones: Conecte el adaptador de alimentacin para IT. Manuale di istruzioni: Collegare LV. NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 PL. Instrukcja obsugi: Podcz adapter zasilania, aby wczy urzdzenie. Otwrz SK. Nvod na pouitie: Pripojte napjac adaptr k zapnutiu prstroja. Otvorte 192.168.88.1 vo webovom prehliadai pre konfigurciu produktu. Viac FI. Kyttohje: Kytke virtalhde plle laitteen. Avaa 192.168.88.1 in selaimen mritt tuotteen. Lis tietoa http://wiki.mikrotik.com SI. Navodila: Prikljuite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Ve informacij v PT. Manual de instrues: Conecte o adaptador de GR. SE. See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 19-Jun-18