PWR-LINE AP kit The PWR-LINE series devices allow Ethernet like connectivity between supported devices over regular electrical power lines. When plugged into the same electrical circuit, the PWR devices will establish Ethernet connectivity by using the HomePlug AV standard. The PWR-LINE AP is a wireless access point with a single Ethernet port, a built-in 802.11b/g/n WiFi Access Point and integrated PWR-LINE support. This particular kit allows you to plug one of the devices directly to your ISP cable or modem, and another supported device somewhere further in your premises, allowing to extend wireless network coverage without needing to install any LAN cables. You can install more PWR-LINE devices to further build your network. Connecting 1. Plug one PWR-LINE AP device into a power socket. 2. Connect your Internet cable to the ethernet port. 3. From your PC or smartphone, connect to the wireless network name which starts with MikroTik. 4. Once connected, open http://192.168.88.1 in your web browser to start configuration. Since there is no password by default, you will be logged in automatically. Set up your password in the screen that loads. Please also specify your country, to make sure local regulations are observed.
(Optional) to add more devices that will connect over the electrical lines, add compatible devices somewhere in the same electrical circuit. Devices sold in kits are already paired, and your local network will automatically be extended. See section Buttons and Jumpers on how to pair individual PWR-LINE devices. 5. RouterOS includes many configuration options in addition to what is described in this document. We suggest to start here to get yourself accustomed to the possibilities: http://mt.lv/help In case IP connection is not available, the Winbox tool (http://mt.lv/winbox) can be used to connect to the MAC address of the device from the LAN side (all access is blocked from the internet port by default). For recovery purposes, it is possible to boot the device from network, see section Buttons and Jumpers. Powering The device accepts powering directly from 110-240 V wall socket it is plugged into. The power consumption under maximum load can reach 5 W. Extension Slots and Ports One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables for connecting to other network devices. Integrated Wireless 2.4 GHz 802.11b/g/n with onboard PIF antennas, max gain 1.5 dBi. See https://mikrotik.com for more information. Contact support@mikrotik.com for help. Document #40812, Modified on 05/30/18 Buttons and Jumpers The PWR-LINE AP has the following buttons:
Reset button Hold the button before powering on the device, and at power up, the button will force load the backup boot loader. Continue holding the button for the other two functions of this button. Release the button when green LED starts flashing, to reset RouterOS configuration. To not load backup boot loader, you can start holding the button after power is already applied. Release the button after LED is no longer flashing (~20 seconds) to cause device to look for Netinstall servers (required for reinstalling RouterOS over network). Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. Useful for RouterBOOT debugging and recovery. PWR connection button (lock icon) Hold 0.5 3 seconds. For 120 seconds will try to communicate with another PWR-LINE device. A blinking orange LED light indicates that it is in search mode. You have to also do the same on the other PWR device, so they can synchronize. Press button again to cancel the search. You can also manually set the security keys in RouterOS settings. Hold 5 8 seconds. A new security key is generated. This is needed to remove a PWR-LINE device from an existing PWR network. Hold 10 15 seconds. Resets all PWR related settings. Mode button This button can be configured from RouterOS software to execute any user supplied RouterOS script. You can also disable this button. Operating system support The device supports RouterOS software with the version number at or above what is indicated in the RouterOS menu /system resource. Other operating systems have not been tested. See https://mikrotik.com for more information. Contact support@mikrotik.com for help. Document #40812, Modified on 05/30/18 Federal Communication Commission Interference Statement FCC ID: TV7PL64112ND This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT: Exposure to Radio Frequency Radiation. 20cm minimum distance has to be maintained between the antenna and user. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. Industry Canada IC: 7442A-PL64112ND This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. See https://mikrotik.com for more information. Contact support@mikrotik.com for help. Document #40812, Modified on 05/30/18 CE Declaration of Conformity Full Declaration of Conformity (DoC) may be obtained by visiting our product page on https://mikrotik.com Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039. Maximum Output Power (EIRP) in the frequency range 2412-2472 MHz is 20 dBm and in 5150-5250, 5250-
5350 and 5470-5725 MHz ranges it is 23/20/27 dBm (only for applicable models). 2014/53/ec. stetele. 2014/53/
2014/53/ce. EN Hereby, Mikrotkls SIA declares that this routerboard is in compliance with the essential requirements and other relevant provisions of directive 2014/53/ec. BG , Mikrotkls SIA , routerboard CZ Mikrotkls SIA tmto prohlauje, e routerboard spluje zkladn poadavky a vechna pslun ustanoveni smrnice 2014/53/es. DK Undertegnede Mikrotkls SIA erklrer herved, at flgende udstyr routerboard overholder de vsentlige krav og vrige relevante krav i direktiv 2014/53/ef. DE Hiermit erklrt Mikrotkls SIA dass sich das gert routerboard in bereinstimmung mit den grundlegenden anforderungen und den brigen einschlgigen bestimmungen der richtlinie 2014/53/eg befindet. EE Kesolevaga kinnitab Mikrotkls SIA seadme routerboard vastavust direktiivi 2014/53/e phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele GR Mikrotkls SIA routerboard ES Por la presente, Mikrotkls SIA declara que este routerboard cumple con los requisitos esenciales y otras exigencias relevantes de la directiva 2014/53/ec. IT Con la presente Mikrotkls SIA dichiara che questo routerboard conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva LV Ar o Mikrotkls SIA deklar, ka routerboard atbilst direktvas 2014/53/ek btiskajm prasbm un citiem ar to saisttajiem noteikumiem. LT iuo Mikrotkls SIA deklaruoja, kad is routerboard atitinka esminius reikalavimus ir kitas 2014/53/eb direktyvos nuostatas HU A Mikrotkls SIA ezzennel kijelenti, hogy a routerboard tpus beren-dezs teljesti az alapvet kvetelmnyeket s ms 2014/53/ek irnyelvben meghatrozott vonatkoz rendelkezseket. 2014/53/eg. NL Hierbij verklaart Mikrotkls SIA dat het toestel l routerboard in overeenstemming is met de essentile eisen en de andere relevante bepalin-gen van richtlijn PL Niniejszym Mikrotkls SIA deklaruje e routerboard jest zgodny z zasadniczymi wymaganiami i innymi waciwymi postanowieniami dyrektywy 2014/53/ec. PT Eu, Mikrotkls SIA declaro que o routerboard cumpre os requisitos essenciais e outras provises relevantes da directiva 2014/53/ec. RO Prin prezenta, Mikrotkls SIA declar c aparatul routerboard este n conformitate cu cerinele eseniale i cu alte prevederi pertinente ale directivei 2014/53/ce. SL Mikrotkls SIA tmto vyhlasuje, e routerboard spa zkladn poiadavky a vetky prslun ustanovenia smernice 2014/53/es. SI Mikrotkls SIA izjavlja, da je ta routerboard v skladu z bistvenimi zahtevami in drugimi relevantnimi doloili direktive 2014/53/es. FI Mikrotkls SIA vakuuttaa tten ett routerboard tyyppinen laite on direktiivin 2014/53/ey oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen SE Hrmed intygar Mikrotkls SIA att denna routerboard r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr mukainen. av direktiv 2014/53/eg. NO Mikrotkls SIA erklrer herved at routerboard er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/ef. DK. Instruktionsbog: Tilslut strmadapteren for at tnde for enheden. bn 192.168.88.1 i en IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unit. Aprire 192.168.88.1 in un BG. : , . 192.168.88.1 , CZ. Nvod k pouit: Pipojte napjec adaptr k zapnut pstroje. Otevete 192.168.88.1 ve webovm prohlei EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More information on http://mt.lv/help
. http://mt.lv/help pro konfiguraci produktu. Vce informac najdete v http://mt.lv/help webbrowser til at konfigurere produktet. Mere information i http://mt.lv/help FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. DE. Bedienungsanleitung: Verbinden Sie das Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://mt.lv/help Netzteil, um das Gert einzuschalten. ffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im http://mt.lv/help EE. Kasutusjuhend: hendage toiteadapter seadme sissellitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://mt.lv/help ES. Manual de instrucciones: Conecte el adaptador de alimentacin para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Ms informacin en http://mt.lv/help LV. Lietoanas instrukcija: Pievienojiet Strvas adapteri, lai ieslgtu ierci. Atvrt browser Web per configurare il prodotto. Maggiori informazioni in http://mt.lv/help LT. Naudojimosi instrukcija: Prijunkite maitinimo adapter junkite 192.168.88.1 ar interneta prlku, lai konfigurtu produktu. Plaka informcija http://mt.lv/help rengin. interneto narykl 192.168.88.1 Atidarykite galite konfigruoti gamin. Daugiau informacijos rasite http://mt.lv/help Csatlakoztassa a hlzati adaptert a kszlk bekapcsolshoz. Megnyitsa 192.168.88.1 egy webbngszben belltani a termket. Tbb informci NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser om het product te http://mt.lv/help configureren. Meer informatie in http://mt.lv/help internetowej, aby skonfigurowa urzdzenie. Wicej informacji w http://mt.lv/help aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informaes em http://mt.lv/help RO. Instruciuni de utilizare: Conectai SK. adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 ntr-un browser web pentru a configura produsul. Mai multe informaii n http://mt.lv/help Nvod na pouitie: Pripojte napjac adaptr k zapnutiu prstroja. Otvorte 192.168.88.1 vo webovom prehliadai pre konfigurciu produktu. Viac informci njdete SI. Navodila: Prikljuite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Ve informacij v http://mt.lv/help v http://mt.lv/help FI. Kyttohje: Kytke virtalhde plle laitteen. Avaa 192.168.88.1 in selaimen mritt tuotteen. Lis tietoa http://mt.lv/help ntadaptern fr att sl p enheten. ppna 192.168.88.1 i en webblsare fr att konfigurera produkten. Mer information p http://mt.lv/help GR. Koble strmadapteren for sl p enheten. pne 192.168.88.1 i en nettleser for konfigurere produktet. Mer informasjon p http://mt.lv/help
: . 192.168.88.1 Web
. http://mt.lv/help
. 192.168.88.1 - . : http://mt.lv/hel p PL. Instrukcja obsugi: Podcz adapter zasilania, aby wczy urzdzenie. Otwrz 192.168.88.1 w przegldarce RU. :
PT. Manual de instrues: Conecte o adaptador de alimentao para ligar o SE. Instruktionsmanual: Anslut NO. Bruksanvisningen:
HU. Hasznlati utasts:
EAC mark See https://mikrotik.com for more information. Contact support@mikrotik.com for help. Document #40812, Modified on 05/30/18