Wireless Wire The Wireless Wire is a set of two wAP 60G devices that work in the 60GHz wireless spectrum, the operating temperature of these devices is from 0C up to +50C. Each device has one gigabit ethernet port, and can be powered from a power jack or from ethernet. Devices can be securely mounted on a wall, ceiling or on a pole/mast. Powering Each device accepts power from passive and active (802.3af/at) power sources. A passive PoE injector is included in the box:
Direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 12-57V DC. The first ethernet port accepts passive PoE input 12-57V DC. Configuration Full RouterOS documentation is located here: http://mt.lv/help. Devices included in the Wireless Wire kit have been preconfigured with 60GHz and ethernet interfaces in bridge mode. Other configuration has to be applied according to the documentation manual linked above. Connect each of Wireless Wire devices to your network using an ethernet cable. To be able to communicate between these networks, devices have to be pointed at each other and be in direct line of sight. Once connected the devices will automatically bridge both networks. Access devices by ethernet cable, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.2 for the master device and 192.168.88.3 for the slave device. Username for login is admin and password is printed on the label that can be found on device packaging. For recovery purposes, it is possible boot the device from network, see section Buttons and jumpers. In case IP connection is not available, the Winbox utility can also be used to connect to the MAC address of the device. Buttons and jumpers RouterBOOT reset button has the following functions:
Hold the button before powering on the device, and at power up, the button will force load the backup boot loader. Continue holding the button for the other two functions of this button. Release the button when green LED starts flashing, to reset RouterOS configuration. To not load backup boot loader, you can start holding the button after power is already applied. Release the button after LED is no longer flashing (~20 seconds) to cause device to look for Netinstall servers (required for reinstalling RouterOS over network). Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. Useful for RouterBOOT debugging and recovery. Operating system support The device only supports RouterOS software with the version number at or above what is indicated in the RouterOS menu /system resource. Other operating systems have not been tested. mikrotik See www. com for more information. Contact support@mikrotik.com for support questions. 11-Aug-17 Federal Communication Commission interference statement FCC ID: TV7WAPG60AD This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT: Exposure to Radio Frequency Radiation. 20 cm minimum distance has to be maintained between the antenna and the occupational user and 20 cm to general public. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Antenna Installation. WARNING: It is the installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. Industry Canada IC: 7442A-WAPG60AD This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. MPORTANT NOTE: IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet equipement est conforme aux limites d'exposition aux rayonnements IC etablies pour un environnement non contrle. Cet equipement doit etre installe et utilise avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. See www. mikrotik
.com for more information. Contact support@mikrotik.com for support questions. 11-Aug-17 CE declaration of conformity Full Declaration of Conformity (DoC) may be obtained by visiting our product page on https://mikrotik.com
[EN] English
[BG] Bulgarian
[CZ] Czech
[DK] Danish
[DE] German
[EE] Estonian
[GR] Greek
[ES] Spanish
[IT] Italian
[LV] Latvian
[LT] Lithuanian
[HU] Hungarian
[NL] Dutch
[PL] Polish
[PT] Portuguese
[RO] Romanian
[SK] Slovak
[SI] Slovenian
[FI] Finish
[SE] Swedish
[NO] Norwegian Hereby, MIKROTKLS SIA declares that the radio equipment RBwAPG-60ad is in compliance with Directive 2014/53/EU
, MIKROTKLS SIA , RBwAPG-60ad 2014/53/EC. MIKROTKLS SIA tmto prohlauje, e RBwAPG-60ad spluje zkladn poadavky a vechna pslun ustanoveni Smrnice 2014/53/ES. Undertegnede MIKROTKLS SIA erklrer herved, at flgende udstyr RBwAPG-60ad overholder de vsentlige krav og vrige relevante krav i direktiv 2014/53/EF. Hiermit erklrt MIKROTKLS SIA dass sich das Gert RBwAPG-60ad in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 2014/53/EG befindet. Kesolevaga kinnitab MIKROTKLS SIA seadme RBwAPG-60ad vastavust direktiivi 2014/53/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. MIKROTKLS SIA RBwAPG-60ad 2014/53/
Por la presente, MIKROTKLS SIA declara que este RBwAPG-60ad cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 2014/53/EC. Con la presente MIKROTKLS SIA dichiara che questo RBwAPG-60ad conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/CE. Ar o MIKROTKLS SIA deklar, ka RBwAPG-60ad atbilst Direktvas 2014/53/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo MIKROTKLS SIA deklaruoja, kad is RBwAPG-60ad atitinka esminius reikalavimus ir kitas 2014/53/EB Direktyvos nuostatas A MIKROTKLS SIA ezzennel kijelenti, hogy a RBwAPG-60ad tpus beren-dezes teljesti az alapvet kvetelmenyeket es ms 2014/53/EK irnyelvben meghatrozott vonatkoz rendelkezeseket. Hierbij verklaart MIKROTKLS SIA dat het toestel l RBwAPG-60ad in overeenstemming is met de essentile eisen en de andere relevante bepalin-
gen van richtlijn 2014/53/EG. Niniejszym MIKROTKLS SIA deklaruje e RBwAPG-60ad jest zgodny z zasadniczymi wymaganiami i innymi waciwymi postanowieniami Dyrektywy 2014/53/EC. Eu, MIKROTKLS SIA declaro que o RBwAPG-60ad cumpre os requisitos essenciais e outras provises relevantes da Directiva 2014/53/EC. Prin prezenta, MIKROTKLS SIA declar c aparatul RBwAPG-60ad este n conformitate cu cerinele eseniale i cu alte prevederi pertinente ale Directivei 2014/53/CE. MIKROTKLS SIA tmto vyhlasuje, e RBwAPG-60ad spa zkladne poiadavky a vetky prslune ustanovenia Smernice 2014/53/ES. MIKROTKLS SIA izjavlja, da je ta RBwAPG-60ad v skladu z bistvenimi zahtevami in drugimi relevantnimi doloili direktive 2014/53/ES. MIKROTKLS SIA vakuuttaa tten ett RBwAPG-60ad tyyppinen laite on direktiivin 2014/53/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hrmed intygar MIKROTKLS SIA att denna RBwAPG-60ad r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 2014/53/EG. MIKROTKLS SIA Erklrer herved at RBwAPG-60ad er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/EF. DK. Instruktionsbog: Tilslut strmadapteren EE. Kasutusjuhend: hendage toiteadapter seadme CZ. Nvod k pouit: Pipojte napjec adapter k zapnut pstroje. Otevete DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gert einzuschalten. ffnen Sie 192.168.88.2/192.168.88.3 in IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unit. Aprire 192.168.88.2/192.168.88.3 in un browser Web per EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.2/192.168.88.3 in your web browser, to configure it. More information BG. : , . 192.168.88.2/192.168.88.3 , on http://mt.lv/help
. http://mt.lv/help 192.168.88.2/192.168.88.3 ve webovem prohlei pro konfiguraci produktu. Vce informac najdete v http://mt.lv/help for at tnde for enheden. bn 192.168.88.2/192.168.88.3 i en webbrowser til at konfigurere produktet. Mere information i http://mt.lv/help FR. Mode d'emploi:
Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.2/192.168.88.3 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://mt.lv/help einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im http://mt.lv/help sissellitamiseks. Avatud 192.168.88.2/192.168.88.3 in veebilehitseja seadistada toodet. Rohkem teavet http://mt.lv/help adaptador de alimentacin para encender la unidad. Abra 192.168.88.2/192.168.88.3 en un navegador web para configurar el producto. Ms informacin en http://mt.lv/help configurare il prodotto. Maggiori informazioni in http://mt.lv/help 192.168.88.2/192.168.88.3 ar interneta prlku, lai konfigurtu produktu. Plaka informcija http://mt.lv/help adapter junkite rengin. interneto narykl 192.168.88.2/192.168.88.3 Atidarykite galite konfigruoti gamin. Daugiau informacijos rasite http://mt.lv/help Hasznlati utasts: Csatlakoztassa a hlzati adaptert a keszlek bekapcsolshoz. Megnyitsa 192.168.88.2/192.168.88.3 egy webbngeszben belltani a NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.2/192.168.88.3 in een termeket. Tbb informci http://mt.lv/help webbrowser om het product te configureren. Meer informatie in http://mt.lv/help 192.168.88.2/192.168.88.3 w przegldarce internetowej, aby skonfigurowa urzdzenie. Wicej informacji w http://mt.lv/help adaptador de alimentao para ligar o aparelho. Abra 192.168.88.2/192.168.88.3 em um navegador da web para configurar o produto. Mais informaes em http://mt.lv/help RO. Instruc iuni de utilizare pentru a configura produsul. Mai multe informa ii n http://mt.lv/help 192.168.88.2/192.168.88.3 vo webovom prehliadai pre konfigurciu produktu. Viac informci njdete v http://mt.lv/help naprave. Odprite 192.168.88.2/192.168.88.3 v spletnem brskalniku nastaviti izdelek. Ve informacij v http://mt.lv/help Avaa 192.168.88.2/192.168.88.3 in selaimen mritt tuotteen. Lis tietoa http://mt.lv/help NO. Bruksanvisningen: Koble ppna 192.168.88.2/192.168.88.3 i en webblsare fr att konfigurera produkten. Mer information p http://mt.lv/help GR. strmadapteren for sl p enheten. pne 192.168.88.2/192.168.88.3 i en nettleser for konfigurere produktet. Mer informasjon p http://mt.lv/help
: . 192.168.88.2/192.168.88.3 Web
. http://mt.lv/help PL. Instrukcja obsugi: Podcz adapter zasilania, aby wczy urzdzenie. Otwrz PT. Manual de instrues: Conecte o
: Conecta i adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.2/192.168.88.3 ntr-un browser web SI. Navodila: Prikljuite napajalnik za vklop FI. Kyttohje: Kytke virtalhde plle laitteen. LV. Lietoanas instrukcija: Pievienojiet Strvas adapteri, lai ieslgtu ierci. Atvrt SK. Nvod na pouitie: Pripojte napjac adapter k zapnutiu prstroja. Otvorte SE. Instruktionsmanual: Anslut ntadaptern fr att sl p enheten. LT. Naudojimosi instrukcija: Prijunkite maitinimo ES. Manual de instrucciones: Conecte el HU. CE Statement. For MPE Statement Mobile device This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Operational mode: 60GHz: 58.32GHz, 60.48GHz, 62.64GHz The frequency and the maximum transmitted power in EU are listed below:
60GHz: 30.58 dBm Manufacturer: Mikrotikls SIA, Pernavas street 46, Riga, Latvia, LV1009 mikrotik See www. com for more information. Contact support@mikrotik.com for support questions. 11-Aug-17