wsAP ac lite The wsAP is a wall socket wireless access point. It is already configured, you can simply connect the Internet cable and start using wireless Internet. We recommend you to set up a password to secure your device. As with any MikroTik wireless access point, you can also manage it using the CAPsMAN wireless access point management server. In this case, all configuration will be done in CAPsMAN. See Buttons and jumpers on how to set this device as a managed CAP. Mounting The device should be mounted on standard electrical wall boxes, where ethernet cabling has already been installed. The included mounting plate fits most worldwide wall box standards. Orient the wall mounting plate on top of your wall box, and install the screws that fit your wall box screw holes the best. Once the plate is in place, plug the required cables into the wsAP unit, and mount the unit on the mounting plate by putting it on the mounting hooks and slightly pulling it downward, to secure in place. Powering The device only accepts powering at the E1 port with PoE, so you must either use the included passive PoE injector, or make sure your switch supports passive or 802.3af/at PoE output. The power consumption under maximum load can reach 8 W. Setup 1. Connect your Internet cable to the E1 port. 2. Set your computer IP configuration to automatic (DHCP). 3. From your computer, connect to the wireless network name which starts with MikroTik, or connect to the E2 ethernet port. 4. The E3 port supports PoE output, so you can power an IP phone from this port. The E3 automatically detects if the connected device supports PoE input, so you can also safely connect devices that do not support PoE powering. 5. Once connected to the wireless network, open http://
192.168.88.1 in your web browser to start configuration, since there is no password by default, you will be logged in automatically. Set up your password in the screen that loads. Configuration By default, the device is configured as a wireless access point, with the first ethernet port (E1) configured as a DHCP client, and the E2 / E3 interfaces are bridged together with the wireless interface. A DHCP server is configured on the bridge interface. The RJ11 phone port is passive passthrough only, to connect your line to the back of the unit, and to connect the RJ11 compatible phone on the front of the unit for better cable management. RouterOS includes many configuration options in addition to what is described in this document. We suggest to start here to get yourself accustomed to the possibilities: http://mt.lv/help. In case IP connection is not available, the Winbox tool (http://mt.lv/winbox) can be used to connect to the MAC address of the device from the LAN side (all access is blocked from the Internet port by default). For recovery purposes, it is possible boot the device from network, see section Buttons and jumpers. See www.mikrotik.com for more information or contact support@mikrotik.com 24-Aug-17 Extension slots and ports Three RJ45 ethernet ports that support automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables for connecting to other network devices. The E3 port is capable of powering another RouterBOARD device with passive and 802.3af/at PoE. The maximum output current is 500 mA when using less than 30 V to power this device and 420 mA when using more than 30 V. Two directly linked (passthrough) RJ11 ports. One Dedicated Charging Port (USB) with max 1.5 A output at 5 V. Only for charging mobile devices. Integrated wireless module which supports AP/CPE/P2P/Repeater modes. Buttons and jumpers Reset button Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds). Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10 seconds). Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds). Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. Useful for RouterBOOT debugging and recovery. Mode button The action of the mode button can be configured from RouterOS software to execute any user supplied RouterOS script. You can also disable this button. By default, the button will run a script, which will disable all LED lights. Useful after you have connected all devices, before mounting the unit on the wall. LED indicators There are eight LED lights on the unit, which can be controlled in RouterOS software, or disabled altogether. 5G and 2G indicate the wireless activity on the 5 GHz and 2 GHz wireless interfaces. E1, E2 and E3 indicate the port activity of the respective ethernet ports. Power LED is lit when the router is powered from the E1 port. The user LED can be configured from RouterOS. Operating system support The device supports RouterOS software with the version number at or above what is indicated in the RouterOS menu /system resource. Other operating systems have not been tested. ENVIRONMENTAL CONDITIONS
- Temperature: -20-55oC
- Temperature: -10-50C
- Humidity: 30-60 %
- Atmospheric pressure: 86-106 kPa See www.mikrotik.com for more information or contact support@mikrotik.com 24-Aug-17 Federal Communication Commission Interference Statement FCC ID: TV7WSAP5HAC2ND This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT: Exposure to Radio Frequency Radiation. 20 cm minimum distance has to be maintained between IMPORTANT: Exposure to Radio Frequency Radiation. 13 cm minimum distance has to be maintained between the antenna and user. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. per antenna type. Professional installation is required of equipment with connectors to ensure compliance with Industry Canada IC: 7442A-WSAP5HAC2ND This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency Exposure Statement for IC: The device has been evaluated to meet general RF exposure requirements. The device can be used in mobile exposure conditions. The min separation distance is 20cm. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Dclaration d'exposition la radiofrquence pour IC: L'appareil a t valu pour rpondre aux exigences gnrales d'exposition aux radiofrquences. L'appareil peut tre utilis dans des conditions d'exposition mobiles. La distance de sparation min est de 20 cm. See www.mikrotik.com for more information or contact support@mikrotik.com 24-Aug-17 CE Declaration of Conformity Full Declaration of Conformity (DoC) may be obtained by visiting our product page on https://mikrotik.com
[EN] English
[BG] Bulgarian
[CZ] Czech
[DK] Danish
[DE] German
[EE] Estonian
[GR] Greek
[ES] Spanish
[IT] Italian Hereby, MIKROTKLS SIA declares that this RouterBOARD is in compliance with the essental requirements and other relevant provisions of Directve 2014/53/EC.
, MIKROTKLS SIA , RouterBOARD 2014/53/EC. MIKROTKLS SIA tmto prohlauje, e RouterBOARD spluje zkladn poadavky a vechna pslun ustanoveni Smrnice 2014/53/ES. Undertegnede MIKROTKLS SIA erklrer herved, at flgende udstyr RouterBOARD overholder de vsentlige krav og vrige relevante krav i direktv 2014/53/EF. Hiermit erklrt MIKROTKLS SIA dass sich das Gert RouterBOARD in bereinstmmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestmmungen der Richtlinie 2014/53/EG befndet. Kesolevaga kinnitab MIKROTKLS SIA seadme RouterBOARD vastavust direktivi 2014/53/E phinuetele ja nimetatud direktivist tulenevatele teistele asjakohastele stetele. MIKROTKLS SIA RouterBOARD 2014/53/
Por la presente, MIKROTKLS SIA declara que este RouterBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la Directva 2014/53/EC. Con la presente MIKROTKLS SIA dichiara che questo RouterBOARD conforme ai requisit essenziali ed alle altre disposizioni pertnent stabilite dalla diretva 2014/53/CE. Ar o MIKROTKLS SIA deklar, ka RouterBOARD atbilst Direktvas 2014/53/EK btskajm prasbm un citem ar to saisttajiem noteikumiem. iuo MIKROTKLS SIA deklaruoja, kad is RouterBOARD attnka esminius reikalavimus ir kitas 2014/53/EB Direktyvos nuostatas
[LV] Latvian
[LT] Lithuanian
[HU] Hungarian A MIKROTKLS SIA ezzennel kijelent, hogy a RouterBOARD tpus beren-dezs teljest az alapvet kvetelmnyeket s ms 2014/53/EK
[NL] Dutch
[PL] Polish irnyelvben meghatrozot vonatkozz rendelkezseket. Hierbij verklaart MIKROTKLS SIA dat het toestel l RouterBOARD in overeenstemming is met de essentile eisen en de andere relevante bepalin-gen van richtlijn 2014/53/EG. Niniejszym MIKROTKLS SIA deklaruje e RouterBOARD jest zgodny z zasadniczymi wymaganiami i innymi waciwymi postanowieniami Dyrektywy 2014/53/EC.
[PT] Portuguese Eu, MIKROTKLS SIA declaro que o RouterBOARD cumpre os requisitos essenciais e outras provises relevantes da Directva 2014/53/EC.
[RO] Romanian Prin prezenta, MIKROTKLS SIA declar c aparatul RouterBOARD este n conformitate cu cerinele eseniale i cu alte prevederi pertnente ale Directvei 2014/53/CE. MIKROTKLS SIA tmto vyhlasuje, e RouterBOARD spa zkladn poiadavky a vetky prslun ustanovenia Smernice 2014/53/ES. MIKROTKLS SIA izjavlja, da je ta RouterBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi doloili direktve 2014/53/ES. MIKROTKLS SIA vakuutaa tten et RouterBOARD tyyppinen laite on direktivin 2014/53/EY oleellisten vaatmusten ja sit koskevien direktivin muiden ehtojen mukainen. Hrmed intygar MIKROTKLS SIA att denna RouterBOARD r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 2014/53/EG.
[SK] Slovak
[SI] Slovenian
[FI] Finish
[SE] Swedish
[NO] Norwegian MIKROTKLS SIA Erklrer herved at RouterBOARD er i samsvar med de grunnleggende krav og vrige relevante krav i direktv 2014/53/EF. EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More information on http://mt.lv/help BG. : , . 192.168.88.1
, . http://mt.lv/help CZ. Nvod k pouit: Pipojte napjec adaptr k zapnut pstroje. Otevete 192.168.88.1 ve webovm prohlei pro konfiguraci produktu. Vce informac najdete v http://mt.lv/help DK. Instruktionsbog: Tilslut strmadapteren for at tnde for enheden. bn 192.168.88.1 i en webbrowser til at konfigurere produktet. Mere information i http://mt.lv/help FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://mt.lv/help DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gert einzuschalten. ffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im http://mt.lv/help EE. Kasutusjuhend: hendage toiteadapter seadme sissellitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://mt.lv/help ES. Manual de instrucciones: Conecte el adaptador de alimentacin para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Ms informacin en http://mt.lv/help IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unit. Aprire 192.168.88.1 in un browser Web per configurare il prodotto. Maggiori informazioni in http://mt.lv/help LV. Lietoanas instrukcija: Pievienojiet Strvas adapteri, lai ieslgtu ierci. Atvrt 192.168.88.1 ar interneta prlku, lai konfigurtu produktu. Plaka informcija http://mt.lv/help LT. Naudojimosi instrukcija: Prijunkite maitinimo adapter junkite rengin. interneto narykl 192.168.88.1 Atidarykite galite konfigruoti gamin. Daugiau informacijos rasite http://mt.lv/help HU. Hasznlati utasts:
Csatlakoztassa a hlzati adaptert a kszlk bekapcsolshoz. Megnyitsa 192.168.88.1 egy webbngszben belltani a termket. Tbb informci http://mt.lv/help NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser om het product te configureren. Meer informatie in http://mt.lv/help PL. Instrukcja obsugi: Podcz adapter zasilania, aby wczy urzdzenie. Otwrz 192.168.88.1 w przegldarce internetowej, aby skonfigurowa urzdzenie. Wicej informacji w http://mt.lv/help PT. Manual de instrues: Conecte o adaptador de alimentao para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informaes em http://mt.lv/help RO. Instruc iuni de utilizare
: Conecta i adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 ntr-un browser web pentru a configura produsul. Mai multe informa ii n http://mt.lv/help SK. Nvod na pouitie:
Pripojte napjac adaptr k zapnutiu prstroja. Otvorte 192.168.88.1 vo webovom prehliadai pre konfigurciu produktu. Viac informci njdete v http://mt.lv/help SI. Navodila: Prikljuite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Ve informacij v http://mt.lv/help FI. Kyttohje: Kytke virtalhde plle laitteen. Avaa 192.168.88.1 in selaimen mritt tuotteen. Lis tietoa http://mt.lv/help SE. Instruktionsmanual: Anslut ntadaptern fr att sl p enheten. ppna 192.168.88.1 i en webblsare fr att konfigurera produkten. Mer information p http://mt.lv/help NO. Bruksanvisningen: Koble strmadapteren for sl p enheten. pne 192.168.88.1 i en nettleser for konfigurere produktet. Mer informasjon p http://mt.lv/help GR. :
. 192.168.88.1 Web . http://mt.lv/help/
See www.mikrotik.com for more information or contact support@mikrotik.com 24-Aug-17