FCC ID: 2AVCWMWC-713 IEEE802.11ad 60GHz Module

MWC-713 User Manual MWC-713 User Manual 60GHz RF/BB Module with USB3.0 interface Rev. 1.0 2020-11-26 Miliwave 1 / 5 Date Written by Rev. Description 20.11.26 Ken. Jung 1.0 MWC-713 User manual .1.0 Release MWC-713 User Manual Revision History Address: #423 , 105 YoungTong-Gu, SuWon-Si, GyeongGi-Do, 16229 Korea http://www.miliwave.co.kr/

Tel. 070-8825-0630 Fax. Email: sales@miliwave.co.kr Copyright Miliwave Inc. 2020. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Miliwave Co., Ltd. All specification supplied herein are subject to change without notice at any time. 2 / 5 Miliwave MWC-713 User Manual 1.Introduction 1.1 Overview Miliwaves MWC-713 module operates in 60GHz unlicensed frequency band, IEEE802.11ad compliant, and is designed for Point to Multi-Pont (PTMP) or Point to Point (PTP) bridge wireless communication, primarily for Line-of Sight (LOS) operation.The MWC-713 module connects to a Linux based Host Communication Processor board via an available USB 3.0 Type-c port . All required drivers and firmware is pre-installed on the MWC-713 module as a self-contained device . However, the MWC-713 module would not be operational unless it is connected to the Linux-based Host Communication Processor board for PTP or PTMP bridge wireless communication.

<Figure 1. MWC-713 Module>

For more information, please contact your Miliwave (sales@miliwave.co.kr) 1.2 Abbreviations and Acronym Definitions Institute of Electrical and Electronics Engineers Definition Giga bits per second Giga Hertz Light Emitting Diode line-of-sight Mega bits per second Modulation and Coding Scheme Mega Hertz Point-to-multipoint Communication Quadrature amplitude modulation Acronym Gbps GHz IEEE LED LoS Mbps MCS MHz PTMP QAM Miliwave 3 / 5 MWC-713 User Manual 1.3 MWC-713 Module Description The Miliwave's MWC-713 module in conjunction with the Host Communication Processor board can function as a PTP or PTMP bridge communication . Main chracteristics of the MWC-713 module include:

- Adaptive Modulation and Link Adaptation: Up to 16QAM and MCS1-12 support

- Air Gap Phased Array Planar Antena: EIRP 36dBm,

- Beam sweep range : Elevation 60, Azimuth 60

- Advanced Security: AES-128

- Compact Form Factor: 52mm x 55mm x14mm

- Connectivity: USB 3.0 Type-C, 60GHz wireless 2. Technical Specifications

- Aggregate capacity: Upto 1.4 Gbps uni-directional, Upto 2.8 Gbps bi-directional

- Latency : less than 1 millisecond round-trip

- Security: AES-128

- I/O interface: USB 3.0(Type-C)

- Other Interface: LEDs indicators for connection status 3.0 Radio Specifications

- Access Technlogy: Single Carrier beam-forming physical layer

- Time Division Duplex

- Frequencies: 59.40 ~ 65.88GHz

- Channel Bandwidth: 2.16 GHz

- Antenna:4x8 Air gap Phased Array Planar Antena beam-forming with 60 degree horizontal and 60 degree vertical

- EIRP: 36 dBm 4.0 Mechanical, Power and Environmental Specification

- Dimension: 52mm x 55mm x14m

- Weight: 96g

- Power Consumption: 4W(Max)

- Operating Temperature: -40C ~ +85C

- Humidity: 5%~95%

5.0 Module Throughput

- MCS Index : 1-12,

- Modulation: BPSK,QPSK,16QAM

- Data Rate : Max PHY rate 4620 Mbit/s 6.0 Installation The MWC-713 could only be installed with Host Communication Processor board at the factory level. There is no user serviceable parts in the MWC-713 module 4 / 5 Miliwave MWC-713 User Manual 7.0 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. 8.0 OEM Responsibilities to comply with FCC The OEM integrator is responsible for ensuring that the enduser has no manual instructions to remove or install module. The module is limited to installation in mobile or fixed applications. The transmitter module must not be colocated or operating in conjunction with any other antenna or transmitter except in accordance with FCC multitransmitter product procedures.

-Separate approval will be required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations other than supplied antennas. As long as the condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their endproduct for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Also, the OEM integrator is responsible to provide to the host manufacturer for compliance with the Part 15B requirements. 9.0 Host User Manual The host manual shall include the following regulatory statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. 10.0 Host Product labeling The module is labeled with its own FCC. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:

Contains FCC ID: 2AVCWMWC-713 Miliwave 5 / 5

423, 105, Gwanggyo-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, South Korea Miliwave Co., Ltd. Date: Dec 23,. 2020 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA RE: Request of Confidentiality for FCC ID: 2AVCWMWC-713 To Whom It may Concern:

Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Miliwave Co., Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Miliwave Co., Ltd. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows:

Exhibit Description PERMANENT & SHORT-TERM CONFIDENTIAL LIST PERMANENT SHORT-TERM 1 2 3 4 5 6 7 8 9 Block Diagram Schematics Part Lists Operation Description NA Internal Photos External Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Sean Rha VP of Business Development

Miliwave Co., Ltd. Room423, GwangGyo-Ro, YeongTong-Gu, Suwon-Si FCC ID: 2AVCWMWC-713 MODULAR APPROVAL LETTER Modular Approval Requirement Answers

(i) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements.

(ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation.

(iii) The modular transmitter must have its own power supply regulation.

(iv) The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section.

(v) The module must demonstrate compliance in a stand-alone configuration.

(vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization.

(viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Sincerely, Yes Yes Yes Yes Yes Yes Yes Yes Name: Sean Rha Title: VP of Business Development

423, 105, Gwanggyo-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, South Korea Miliwave Co., Ltd. Date: Dec 23, 2020 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA Sean Rha VP of Business Development Letter of Authorization We, the undersigned, hereby authorize Guenki Son of DT&C Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: 2AVCWMWC-713 including signing of all documents relating to these matters. Any and all acts carried out by Guenki Son of DT&C Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Miliwave Co., Ltd. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Sincerely,