FCC ID: 2AVCWMWC415 IEEE802.11ad 60GHz

MWC415 User Manual MWC415 User Manual 60GHz RF/BB Module with USB3.0 interface Rev. 1.0 2020-06-17 Miliwave 1 / 7 MWC415 User Manual Revision History Date Written by Rev. Description 20.006.17 Ken. Jung 1.0 MWC415 User manual .1.0 Release Address: 423 R&DB Center, 105 YoungTong-Gu, SuWon-Si, GyeongGi-Do, 16229 Korea http://www.miliwave.co.kr/

Tel. 070-8825-0630 Fax. Email: sales@miliwave.co.kr without notice at any time. Miliwave Copyright Miliwave Inc. 2020. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Miliwave Co., Ltd. All specification supplied herein are subject to change 2 / 7 MWC415 User Manual 1.Introduction 1.1 Overview Miliwaves MWC415 module operates in the 60GHz unlicensed frequency band, IEEE802.11ad compliant, and is designed for only using for Smart Factory IoT Applications(ex. AMR(Autonounous Moving Robot, Machine Vision Camera) with , Point to Multi-Pont (PTMP) or Point to Point (PTP) bridge wireless communication, primarily for Line-of Sight (LOS) operation. The MWC415 module connects to a Linux based Host Communication Processor board via an available USB 3.0 port . All required drivers and firmware is pre-installed on the MWC415 module as a self-contained device . However, the MWC415 module would not be operational unless it is connected to the Linux-

based Host Communication Processor board for PTP or PTMP bridge wireless communication.

< Figure 1. MWC415 Use Case for Smart Factory(ex. AMR, Machine Vision Camera)>

For more information, please contact your Miliwave (sales@miliwave.co.kr) 3 / 7 Miliwave MWC415 User Manual 1.2 Abbreviations and Acronym Definitions Acronym Gbps GHz IEEE LED LoS Mbps MCS MHz PTMP QAM Institute of Electrical and Electronics Engineers Definition Giga bits per second Giga Hertz Light Emitting Diode line-of-sight Mega bits per second Modulation and Coding Scheme Mega Hertz Point-to-multipoint Communication Quadrature amplitude modulation

<Figure 2. MWC415>

1.3 MWC415 Module Description The Miliwave's MWC415 module in conjunction with the Host Communication Processor board can function as a PTP or PTMP wireless bridge communication . Main chracteristics of the MWC415 module

- Adaptive Modulation and Link Adaptation: Up to 16QAM and MCS1-12 support

- Integrated Phased Array Planar Antena: EIRP 16dBm, 120 degree beam sweep range

- Advanced Security: AES-128

- Compact Form Factor: 37 x14 x 72mm 4 / 7 include:

Miliwave MWC415 User Manual

- Connectivity: USB 3.0 type A, 60GHz wireless 2. Technical Specifications

- Aggregate capacity: 1.0Gbps uni-directional, 2.0 Gbps bi-directional

- Latency : less than 1 millisecond round-trip

- Security: AES-128

- I/O interface: USB 3.0(Type Micro-A)

- Other Interface: LEDs indicators for connection status 3.0 Radio Specifications

- Modulation : Single Carrier(SC)

- Time Division Duplex

- Frequencies: 59.40 ~ 61.56GHz(Ch.2)

- Channel Bandwidth: 2.16 GHz azimuth

- EIRP: 16 dBm 4.0 Mechanical, Power and Environmental Specification

- Dimension(L x W x H): 37 x 14 x 72mm

- Weight: 27g

- Power Consumption: 4W(Max)

- Operating Temperature: -40C ~ +85C

- Humidity: 5%~95%

Miliwave

- Antenna: Double Side Dipoles(DSD) 2 or 4 elements Phased Arrays to Scan over 240 degrees in 5 / 7 MWC415 User Manual 5.0 Module Throughput

- MCS Index : 0~12,

- Modulation: BPSK, QPSK, 16QAM

- Data Rate : Max PHY rate 4620 Mbit/s 6.0 Installation The MWC415 could only be installed with Host Communication Processor board at the factory level. There is no user serviceable parts in the MWC415 module 7.0 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. Miliwave 6 / 7 MWC415 User Manual This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Miliwave 7 / 7

Miliwave Co., Ltd. Model# MWC415 FCC ID : 2AVCWMWC415 [<

sw | HIMTI ON I/NVM TMT TT Mwc41500001 Made in KOREA Miliwave Co., Ltd. Model# MWC415 FCC ID : 2AVCWMWC415 [<

sw | HIMTI ON I/NVM TMT TT Mwc41500001 Made in KOREA Miliwave Co., Ltd. Model# MWC415 FCC ID : 2AVCWMWC415 [<

sw | HIMTI ON I/NVM TMT TT Mwc41500001 Made in KOREA

423, 105, Gwanggyo-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, South Korea Miliwave Co., Ltd. Date: June.15. 2020 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA RE: Request of Confidentiality for FCC ID: 2AVCWMWC415 To Whom It may Concern:

Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Miliwave Co., Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Miliwave Co., Ltd. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows:

Exhibit Description PERMANENT & SHORT-TERM CONFIDENTIAL LIST PERMANENT SHORT-TERM 1 2 3 4 5 6 7 8 9 Block Diagram Schematics Part Lists Operation Description NA Internal Photos External Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Sean Rha VP of Business Development

423, 105, Gwanggyo-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, South Korea Miliwave Co., Ltd. Date: Jun 15, 2020 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA Sean Rha VP of Business Development Letter of Authorization We, the undersigned, hereby authorize Guenki Son of DT&C Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: 2AVCWMWC415 including signing of all documents relating to these matters. Any and all acts carried out by Guenki Son of DT&C Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Miliwave Co., Ltd. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Sincerely,