MWC-708 11AX MU-MIMO OFDMA Dual Band Embedded Board Features Quad-core ARM 64bit A53@1.8GHz Processor 1GB DDRL3L System Memory 8MB NOR Flash, 256MB NAND Flash Supports Dynamic Frequency Selection (DFS) 2x2 On-board 2.4GHz radio, up to 573Mbps physical Data Rate 2x2 On-board 5GHz radio, up to 1201Mbps physical Data Rate Applications 802.11ax MU-MIMO OFDMA Access Point Smart AP TWT Industrial environment data transmission Product Description MWC-708 based on Quad-core ARM 64bit A53@1.8GHz chipset is an enterprise wireless module integrated with 2x2 5G high power Radio module and 2x2 2.4G high power Radio module designed specifically to provide users with mobile access to high-bandwidth video streaming, voice, and data transmission for office and challenging RF environment in factories, warehouses establishment. Absolute Maximum Rating Parameter Supply Voltage Operating Temperature Range Storage Temperature Range Operating Humidity Range Storage Humidity Range Rating 24V~48V(DC Jack)
-40 to +70
-45 to +105 5 to +95 (non-condensing) 0 to +90 (non-condensing) Unit V
http://www.miliwave.net/
1 Hardware Specifications Symbol CPU Qualcomm-Atheros IPQ6010 Parameter CPU Frequency Quad-core ARM 64 bit A53 @1.8 GHz processor System Memory 1GB (2x 512MB) DDR3L 16-bit interface with 32-bit memory bus design Ethernet Port 1 x 2.5Gbps Ethernet Ports & POE USB PoE DC Jack LED Serial Port Wireless Antenna Nor Flash Nand Flash DDR Dimension 1x USB 3.0 Type-C Port 24V~56V passive PoE 48V~56V passive/Active PoE(Suport 802.3bt) 24V~48V power supply 2 x LEDs 1x Serial Port 4 Pin Connector On-board 2x2, 2.4GHz MU-MIMO OFDMA 802.11b/g/n/ax,support DSSS, OFDM, OFDMA On-board 2x2 , 5GHz MU-MIMO OFDMA 802.11a/n/ac/ax,max 20dBm per chain,support OFDM, OFDMA 4x MMCX Connectors 2.4G, 5G Wi-Fi rod antenna-1: ALX19X-221050-00 2.4G, 5G Wi-Fi rod antenna-2: DRA2G5GD002 5G Wi-Fi patch antenna-1: OLX23P-097100-A 5G Wi-Fi patch antenna-2: OLX23P-097100-B 2.4G Wi-Fi PCB antenna: ALX19P-051AA2-02 8MB 256MB 2 x 512MB 120mm x 105mm x 20mm http://www.miliwave.net/
2 2.4G WIFI Maximum Output Power:
Operating Band/Frequency:
Channel Number:
5G WIFI Maximum Output Power:
Operating Frequency Channel Number Channel Separation 802.11b: 22.92 dBm 802.11g: 21.42 dBm 802.11n20: 22.34 dBm 802.11n40: 18.72 dBm 802.11ax20: 22.65 dBm 802.11ax40: 18.35 dBm 2412~2462 MHz(802.11b/g/n20/ax20), 2422~2452 MHz(802.11n40/ax40) 11(802.11b/g/n20/ax20), 7(802.11n40/ax40) 5G Wi-Fi B1:
802.11a:16.82 dBm 802.11ac20:18.39 dBm 802.11n-HT20:18.39 dBm 802.11ac40:20.33 dBm 802.11n-HT40:20.33 dBm 802.11ac80:10.06 dBm 802.11ax20:18.08 dBm 802.11ax40:19.80 dBm 802.11ax80:9.52 dBm 5G Wi-Fi B4:
21.39 dBm 23.84 dBm 23.85 dBm 24.80 dBm 24.81 dBm 22.10 dBm 23.59 dBm 24.24 dBm 22.10 dBm 5G Wi-Fi B1: 5180-5240 MHz, B4: 5745-5825 MHz 5G Wi-Fi B1: 7, B4: 8 5G Wi-Fi: a/ac20/n20/ax20: 20 MHz, ac40/n40/ax40: 40 MHz, ac80/ax80: 80 MHz http://www.miliwave.net/
3 Interface MAP Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the int interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. CoConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. For 5150-5250MHz used indoor only http://www.miliwave.net/
4