FCC ID: OYE-MTF10 RF Link

AW12-RF/MRF-01 INSTALLATION INSTRUCTIONS Preliminary 1- PARTS LIST PART NUMBERS

-AW12-RF Single Channel Transmitter/Air Wave Switch Assembly

-MRF-01 Single Channel Receiver

-P/N=? Battery, CR2032

-(4) #6-20x3/4, Screw, Self-Drilling 2- INSTALL TRANSMITTER/AIR WAVESWITCH ASSY

-Open box, unpack battery and remove lid from the AW12-RF.

-Install CR2032 battery as shown with the + side up. Notice that the Red LED blinks once upon insertion.

-Now position & attach, with provided screws, your AW12-RF to your bottom angle or end stile of your door. Replace lid.

-Now, dependent upon your kit, make the necessary airline connections. 3- INSTALL RECEIVER

-Open box, remove lid from the MRF-01 receiver.

-Position receiver on operator, so that its wiring will reach the operator terminal strip. Keep in mind that the Green antenna wire must be exposed to the AW12-RF Transmitter/Air Wave Switch. It cannot be behind any type of metal.

-Connect the Red (+) & Black (-) to your 24VAC/DC source. The White wire connects to a low voltage COMMON terminal. The Yellow wire connects to your EDGE/SAFETY terminal. 4- PROGRAMMING

-Apply power to the receiver.

-Green Power LED stays on; Channel 1 Red LED will be blinking.

-To enter Learn mode simply press your fingertip onto CH1 (in the LEARN BUTTON section of the PCB). The Red LED remains on and the Amber Learn LED will begin to blink.

-Activate the edge & note the Red &

Amber LEDs will blink alternately rapidly. Then the Red LED will go out &

the Amber LED remains on.

-Channel 1 is now programmed.

-To start-over/erase programming, press and hold CH1 again for 3 seconds, LEDs will blink for 5 seconds & then go into fault mode. 5- TEST SAFETY EDGE

-Ensure that your door stops/reverses when safety edge is activated during close cycle. LED INDICATORS LED Color Green Yellow Power Status Function Description Red

(per channel) Relay State Learn Mode Always On Usually On Off if right out of the box, no transmitter associated. Wink Off once per TX message received. Blinks rapidly during Learn Mode. Off when Relay is Clear. On when Relay is in Fault. Blink very slowly for Low Battery. Blink slowly if no TX has been associated. On when this channel is in Learn Mode

(Yellow blinking). Blinks rapidly when Learn Mode is complete. 5- Specifications and Controls: Transmitter Unit Frequency: 915 MHz. FSK Modulation. Indicator Lights: Red LED: Tx Data Power Source: Batteries: CR2032 Coincell. 3.0VDC Lithium. Dimensions:

Antenna: Integral PCB loop. Response Time: Nominal 70 msec; Safety Edge Input to Receiver Relay Contact Output. 6-Specifications and Controls: Receiver Unit Indicator Lights: Green LED: Power on; Red LED: Relay energized, indicates safety edge activation;

Yellow LED: Status Power Source: 10 to 40 VDC, 10-30 VAC (RMS) Power Consumption: 16 mA (Idle) with Relay Off; 53 mA (avg.) with Relay On Dimensions: 4.9w x 3.75h x 1.2d Cable Connections: Integral 18 wiring with #8 spade lugs. Maximum Operating Distance: 100 Feet 7- FCC Compliance FCC ID: OYE-MTF10 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. 1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1- Re-orient or relocate the receiver antenna 2- Increase the separation between the equipment and the receiver 3- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4- Consult the dealer or an experienced radio/TVtechnician for help. Changes or Modifications Not Expressly Approved By The Party Responsible For Compliance Could Void The Users Authority To Operate The Equipment. P.O. Box 159 West Grove, PA 19390 800-220-3343 610-869-4422 Fax: 610-869-4423 www.milleredge.com 6809 South Harl Ave., Suite A Tempe, AZ 85283 800-887-3343 480-755-3565 Fax: 480-755-3558

DRAFT INSTALLATION INSTRUCTIONS Model # AW14-RF Pending IMPORTANT:

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. The AW14-RF switch offers installation time savings and improved visual aesthetics as there is no need to hard wire a coil cord or retracting reel. The AW14-RF switch kit includes a MRF-01 receiver which is wired to the motor controls. Kits may be installed on a doors up to18 feet wide. 1-

Parts List PART NUMBER Tools Required:

1. AW14-RF Transmitter/Air Wave Switch Assembly 2. Battery, CR2032 1. 1/8 Phillips Head Screwdriver 2. Mounting Screws (not supplied) 2- Install Transmitter / Air Switch Assembly 2-1. Open and unpack the battery and remove lid from the AW14-RF. 2-2. Install the CR2032 battery as shown with the + side up. Notice that the RED LED blinks once upon insertion. Replace the lid of the AW14-RF 2-3 Position and attach the AW14-RF to the bottom angle or end stile of the door. 2-4 Depending on the configuration, make the necessary airline connections. 2-1 2-2 3- Adjust The Switch Sensitivity 3-1 The AW14 is factory set and should rarely need to be adjusted. If you determine that the switch sensitivity is not correct, to make the switch more sensitive, turn the adjustment screw clock-wise. This will move the screw closer to the diaphragm inside the switch, thus less air movement is required to activate the switch (LED will Blink). Longer edges will require more sensitivity. Too sensitive will cause unwanted activations caused from door vibration. 2-3 2-4 3-1 P.O. Box 159 West Grove, PA 19390 800-220-3343 610-869-4422 Fax: 610-869-4423 www.milleredge.com 6809 South Harl Ave., Suite A Tempe, AZ 85283 800-887-3343 480-755-3565 Fax: 480-755-3558 4- Test Safety Edge 3-1 Ensure that the door stops/reverses when the sensing edge is activated during the close cycle. 5- Transmitter Specifications Frequency: 915 MHz. FSK Modulation Indicator Light: Red LED. Blinks when data is sent. Power Source: CR2032 Coincell Battery 3.0VDC Lithium Antenna: Integral PCB loop Response Time: Nominal 100 msec, Safety Edge Input to Receiver Relay Contact Output Operating Distance: 50 feet minimum, Up to 100 feet depending on conditions Operating Temperature: 14oF - 140oF (-10oC - + 60oC) (Battery Limit) 6- FCC Compliance Transmitter Model: AW14-RF FCC ID: OYE-MTF10 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules.These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1- Re-orient or relocate the receiver antenna 2- Increase the separation between the equipment and the receiver 3- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4- Consult the dealer or an experienced radio/TV technician for help Changes or Modifications Not Expressly Approved By The Party Responsible For Compliance Could Void The User Authority To Operate The Equipment. P.O. Box 159 West Grove, PA 19390 800-220-3343 610-869-4422 Fax: 610-869-4423 www.milleredge.com 6809 South Harl Ave., Suite A Tempe, AZ 85283 800-887-3343 480-755-3565 Fax: 480-755-3558

INSTALLATION INSTRUCTIONS Model # PS20-RF DRAFT Pending IMPORTANT:

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. The PS20RF switch offers installation time savings and improved visual aesthetics as there is no need to hard wire a coil cord or retracting reel. PS20RF switch includes a receiver which is wired to the motor controls. PS20 kits are available as either hard-wired (PS20A) or wireless (PS20RF) complete with receiver. Kits may be installed on a doors up to 18 feet wide. 1-

Parts List PART NUMBER 1. PS20-RF Transmitter/Air Switch Combination 2. HRH-375, Hard Hose, 4 3. Battery, CR2032 Tools Required:

1. 1/8 Phillips Head Screwdriver 2. Mounting Screws (not supplied) 2- Install Transmitter / Air Switch Assembly 2-1. Open and unpack the battery and remove lid from the PS20-RF. 2-2. Install the CR2032 battery as shown with the + side up. Notice that the RED LED blinks once upon insertion. 2-3. Replace the lid of the PS20-RF. 2-4. Insert the PS20-RF nipple into either end of the Hard Hose. 2-5. Insert remaining Hard Hose end into the Gum Rubber Hose located inside the bottom astragal. 2-6. Position and attach the PS20-RF to the bottom angle or end stile of the door, taking care not to pinch close the Hard Rubber or Gum Rubber Hose. 2-1 2-2 2-3 2-4 2-4 2-5 2-6 2-6 P.O. Box 159 West Grove, PA 19390 800-220-3343 610-869-4422 Fax: 610-869-4423 www.milleredge.com 6809 South Harl Ave., Suite A Tempe, AZ 85283 800-887-3343 480-755-3565 Fax: 480-755-3558 3- Test Safety Edge 3-1 Ensure that the door stops/reverses when the sensing edge is activated during the close cycle. 4- Transmitter Specifications Frequency: 915 MHz. FSK Modulation Indicator Light: Red LED. Blinks when data is sent. Power Source: CR2032 Coincell Battery 3.0VDC Lithium Antenna: Integral PCB loop Response Time: Nominal 100 msec, Safety Edge Input to Receiver Relay Contact Output Operating Distance: 50 feet minimum, Up to 100 feet depending on conditions Operating Temperature: 14oF - 140oF (-10oC - + 60oC) 5- FCC Compliance Transmitter Model: PS20-RF FCC ID: OYE-MTF10 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules.These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1- Re-orient or relocate the receiver antenna 2- Increase the separation between the equipment and the receiver 3- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4- Consult the dealer or an experienced radio/TV technician for help Changes or Modifications Not Expressly Approved By The Party Responsible For Compliance Could Void The User Authority To Operate The Equipment. P.O. Box 159 West Grove, PA 19390 800-220-3343 610-869-4422 Fax: 610-869-4423 www.milleredge.com 6809 South Harl Ave., Suite A Tempe, AZ 85283 800-887-3343 480-755-3565 Fax: 480-755-3558