FCC ID: 2A29L-360001C Electronic Kit Keyless System

ELECTRONIC KIT-KEY LESS SYSTEMS MANUAL Introduction Smart Key System employs sophisticated technology provide convenience and peace of mind, coupled with maximum protection, and reliability to your vehicle. The system incorporates two major components; control unit and key FOB. A microprocessor controlled, solid unit connected with in the vehicle. In addition it has a vehicle locater LOCK / UNLOCK operation of the steering lock, fuel cap and seat opener and engine function development with authorization, necessary changes corresponding to the requirements of the particular vehicle model. It is proposed to develop a system CONTROL UNIT suitable for two wheelers for the smart key system. finder Features 1. IGN (Ignition) ON (Engine Start) from the unlocking operation of handle lock Output engine start permission to Engine ECU by IGN ON. In case of detecting the FOB at communication range when PUSH SW of knob is detected. 2. The locking operation of the handle lock from IGN OFF. 3. The locking operation of the handle lock from KNOB SW Press. 4. Detect and notify when the FOB dropped. 5. Detect and notify when the FOB dropped after 50M. 6. Notice of FOB battery voltage reduction. 7. Vehicle Finder. 8. Vehicle Seat function by Key FOB. 9. Vehicle Seat function by seat switch. 10. IGN ON at the emergency (In passive mode). System Diagram UHF LF KEY FOB IP67 level sealing of FOB FOB sensing distance of 1.50.3m Layered Architecture with Modular HW and Software development Answerback function Seat opening FCC ID: 2A29L-365001C IC : 23641-365001C SUPERVISORY CONTROL UNIT IP67 protection level for SCU Layered Architecture with Modular HW and Software development Withstand automotive harsh environment Ultra low quiescent current KEY FOB drop indication FCC ID: 2A29L-360001C IC : 23641-360001C UHF LF SMART IGNITION SWITCH Knob operated function no key required Solenoid based system to lock &

unlock steering User authorization (smart key) check by Electronic control unit Micro-switch based wake-up of Smart ignition switch SCU MOUNTING: Select a mounting location behind the dash, and secure using cable ties and bracket. Be certain that the chosen location will not the vehicle. Avoid mounting the interfere with the proper operation of module to or routing the wiring around the steering column, as the module or wiring could wrap around or block the steering wheel preventing proper control of the vehicle. Specification - SUPERVISORY CONTROL UNIT Model No. Rated Voltage Rated Current Operating Current During Ignition ON Condition Operating Temperature IP Rating Protection Short Circuit Protection Over Voltage Protection in Vehicle Operating Frequency

: EC-360001C

: 12VDC

: 5.5A

: Less than 750mA

: -30C - +80C

: IP67

: Yes

: Yes

: Yes (Fuse Provided)

: 315MHz (UHF)

: 125KHz (LF) Note: SCU mounting at vehicle is rusticated, user can not access the SCU. Specification - KEY FOB Model No. Key FOB Type Rated Voltage Battery Type Recommended Make Operating Temperature Operating Frequency Battery Life IP Rating Symbol Description

: ER-365001C

: Radio Frequency

: 3VDC

: Lithium (#CR2032)

: Panasonic

: -20C - +55C

: 315MHz (UHF)

: 125KHz (LF)

: 1 Year (Typical)

: IP67

Vehicle Finder Seat function Specification - Sticker Caution Marking :

KEY FOB product consists of Coin battery and product is accessible to children due to that product shall consists of caution symbol. FCC ID: 2A29L-365001C IC : 23641-365001C FCC Regulatory Information ( FCC ID is 2A29L-360001C ) :

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received including interference that may cause undesired operation of this device. Any changes or modifications not expressly approved by the party responsible for Compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and , if not Specification - FCC Regulatory Information Specification - IC Regulatory Information IC Statement:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.

"This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. Cet quipement est conforme l'exposition aux rayonnements Industry Canada limites tablies pour un environnement non contrl."

Specification - IC Regulatory Information IC Statement:

Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Minimum separation distance used for NS Measurement 10CM. Distance de sparation minimale utilise pour la mesure NS 10CM.

FCC/IC ID and HVIN shall be permanently indicated on the exterior of the product The name and address, and telephone number, or internet contact information of the responsible Identification of the product, e.g., trade name, model, etc Label must contain, party A statement that the product complies with the rules as mentioned below, This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation SUPERVISORY CONTROL UNIT ( EC-360001C) Label Details :

ATVRheinland TCB Authority to Act as Agent MS-0045317 Number:

Revision:

Effective date: Oct 8, 2021 0 The following is a sample Agency Request letter, which needs to be completed on company letterhead, signed by an authorized Applicant/Agent, and submitted to TUV Rheinland. Authority to Act as Agent Date: 06 June 2022 TUV Rheinland of North America, Inc. 1279 Quarry Lane., Suite. A Pleasanton, CA 94566 To Whom It May Concern:

appoint Mr. Raghavendra Kulkarni to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canada's regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with Hariit Singh, Minda Corporation Limited, D-6-11. Sector-59, Noida, Uttar Pradesh- 201301, India. For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (6), to the application is subject to denial of federal benefits, Thank you, Agency Agreement Date Agreement is valid for 12 months from the above date. By that includes FCC benefits. 06 June 2022 Harit Singh_

(Print name)

+91-9818127076

(Telephone)

(Signature) Head-Engg. Electronics

(Title) On behalf of Minda Corporation Limited

(Company Name) Page 1 of 1

SP RK MINDA

- Powered by Passion MINDA CORPORATION LIMITED

(SECURITY SYSTEM DIVISION) Date: 06 Jun 2022 Subject: Confidentiality Request for FCC ID: 2A29L-06000HC Confidentiality Letter Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term oShort Term OShort Term O Short Term Short Term Term Short OPermanent O Permanent Permanent Permanent Permanent Permanent O Permanent o Permanent Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation INIl software security attestation Part List/Tune-Up Procedure Schematics Test Setup Photos User's Manual Minda Corporation Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently witheld from public review due to materials that coniain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 90 days from the date of the Grant of Equipment Authorization and prior to maketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely By:

Harjit Singh/ Head-Engg. Electronics

(Signature)

(Print name//Title) MINDA CORPORATION LIMITED (SECURITY SYSTEM DIViSION) CIN: L74899DL1985PLCo20401 Office Address: D-6-11, Sector-59, Noida, Uttar Pradesh-201301, India. Tel.: +91-120-4787100; Fax: +91-120-4787201 Registered Office: A-15, Ashok Vihar, Phase -

Website: www.sparkminda.com I, Delhi - 110052.