Parking sensor installation instructions
/Product Summary
External dimensions
quality
Parking sensor
Power supply
Built-in primary battery
Place of use
Set location
Waterproof performance
Operating temperature limit
Notes
Do not use on iron plate, Above ground, outdoors, underground, asphalt, concrete
In parking frame
Please note that it cannot be detected correctly under the following conditions
seawater, under snow, environment where organic solvent may splash,
iron plate on top of sensor
Material name
Shipping material
Materials prepared by the customer
ANCHOR BOLT SCREW BOLT 1
Parking sensor installation instructions
/Mounting method
Content
/parking frame
Set location
Please install the parking sensor in the center of the parking frame
Set face Drilling
Align the mark engraved on the HOUSHING in the direction of vehicle parking
(Photo A Red circle)
At this time, the ANCHOR BOLT hole position of HOUSING is misaligned with the installation direction.
(Photo B ,Blue circle 6 places
HOUSING fixed
After making holes on the installation surface, attach in the following order.
ANCHOR BOLT embedded
HOUSING hole matching installation
Conclude HOUSING at SCREW BOLT
A Photo A
Vehicle receiving direction
B Photo B SCREW BOLT HOUSING ANCHOR BOLT 2
Parking sensor installation instructions
/Mounting method
Content Photo C
C
C2 Photo C2
Operation check
Looking inside the TOP COVER ASSY, look so that the mounting guide convex (*) is on the left
(*) (Photo C2)
Slide the magnet downward from the position indicated by the yellow circle in Photo C. Refer to Photo D1 Photo D2 for the slide procedure.
The magnet is slid from top to bottom twice one way, and if the LED flashes twice after the operation, the operation mode is entered
(LED position: Photo E).
If you accidentally slide the magnet twice or more, wait 5 seconds or more and repeat steps 2 and 3 above.
The sensing function will be activated 5 minutes after the operation mode (operation confirmation is completed). Please perform the following work within 5 minutes to complete the installation.
D1 Photo D1
D2 Photo D2
E Photo E LED2
Check the LED blinks twice 3
Parking sensor installation instructions
/Mounting method
Content
Wearing the TOP COVER ASSY
Check the HOUSING and TOP COVER installation guides and install the TOP COVER ASSY
SCREW
Apply the prescribed SCREW locking adhesive to the SCREW (pictured)
Fasten the adhesive-applied SCREW to the six SCREW holes on the TOP COVER.
SCREW tightening torque is Please set at 2.10N m (210cN m)
Installation completed
Parking sensor installation instructions
FCC Notation related to FCC specifications FCC ID2AWRLNDPM003US Product Parking Sensor Model NDPM003 US This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. q p Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. g
, Contact for US area
-NMB Technologies Corporation Address :9730 Independence Ave, Chatsworth, CA 91311 Tel:805-657-2578 Email: info@nmbtc.com