ADD-ON DEVICE Quickstart Guide Alarm Keypad Model No. KYP1300 What's inside:
1x Alarm Keypad 2x Double-Sided Tapes Mounting Accessories Broadband internet connection, iOS or Android phone and home router required. Get to Know Your Device E n g l i s h 1 2 3 4 1 . Green LED Normal On :
Power on 2. Blue LED Flashes Once :
Arm / Stay or Disarm 3. Red LED 5 6 7 8 9 10 11 12 13 14 Flashes Once :
Wrong programming Flashes Once Every 3 Seconds :
Low battery indication, please replace the batteries. 4. Wake Up Key 5. Arm 6. Arm in Stay Mode 7 . Disarm 8. SOS Key 9 . Battery Slot 10. Wired Cables Interface 11 . Tamper Switch The tamper switch will be activated if case is opened 12. Screw Hole 13. Rear Cover 14. Wired Cables Interface Step 1: Assemble your device and accessories 1 . Unpack your device and accessories. 2. Pair the device with the Security Shuttle within 1-10 feet to make sure the connection is working well. 3. Pull and remove the plastic strip to initiate battery contact. E n g l i s h 1-10 ft 1-10 ft Step 2: Add a device 1 . Open the app, tap on the menu button "
" and select "Device Management". 2. Press the add button " + " next to Sensor List. 3. Follow the app instructions to scan the QR code located on the device. Note: If the scan is incomplete, you will be asked to enter the serial number
(SN) of the device. E n g l i s h Step 3: Mount your device Before you mount your device, see if it's within Security Shuttles range. 1 . Take your device to the room you want to use it in. 2. Press "
" then " SOS " for 3 seconds, if you receive an notification saying " Emergency ", you are within range. Installation 1 2 Open the keypad case, fix the rear cover at the suitable mouting location. Fasten the front cover on the rear cover. 3 E n g l i s h Screw the bottom on. Operation Press "
user password # before operating.
" to activate keypad then enter admin password # or
+
admin password / user password
+
#
Admin password is 123456 as default User password is 1234 as default Note: If there is no operations within 5 seconds after pressing "
will exit setup state automatically.
", keypad Function Arm Arm in Stay Disarm Press Button
+
+
+
1234 1234 1234
+
+
+
Press Press Press E n g l i s h Function Mute Press Button button, then press Press within 1 second to enter Siren Delay - "No Siren - Exclude Emergency Events" mode. Unmute Press cancel Siren Delay mode. button, then press within 1 second to SOS Emergency Call Press SOS for 3 seconds to activate an immidate alarm. Note: It is recommended to enable function of "Emergency Call with Password" to avoid false operation. See Settings. Settings Press "
state. Blue LED will light up. Then insert your command.
" then enter admin password # 9 to enter setting
+
admin password
+
#
+
9 Admin password is 123456 as default. Keypad will be programmed successfully after one beep is heard. Note: No operation within 30 seconds, keypad will automatically exit setup state. E n g l i s h Function Press Button Mark Quick Arm On Quick Arm Off Touch Tone On Touch Tone Off Emergency Call with Password Emergency Call without Password Change Admin Password Change User Password Once enabled, users can press
"
+ " to arm the system without password. 1
#
1 2
#
2 Once enabled, the green LED will flash when a button is pressed. 4
#
4 new password
#
6 digits new password
#
4 digits Arm Delay 0-99s
#
(0-99s) Troubleshooting Tips Are your devices listed in your app?
If youre having trouble installing your devices, see if theyre listed in your app:
Navigate to
> Device Management to see if all your devices are listed. Tap + next to the device category and follow the on-screen instructions to add any missing devices. Are your devices communicating with Security Shuttle?
If your devices dont connect to Security Shuttle, they might be too far away. Take them to a location thats closer to Security Shuttle and try again. If they do connect, youll know the range of your device and where to install a range extender. Alternatively, you can move Security Shuttle closer to your device. If your devices still dont communicate with Security Shuttle, even when theyre in the same room, navigate to Management > + on the app to add your devices again.
> Device Reset to Default Settings Press the Tamper Switch 5 times in a row, then you will heard one long beep. FCC STATEMENT 1 . This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. 99200307MIG V1.0