FCC ID: 2AWTM-RTLS-OEM001 Ultra-Wideband Transceiver Module

Mirion Technologies Ultra-Wideband OEM Module User Manual Version 4 - September 2020 1 Table of Contents Version History Overview Product Specifications Main System Components Mechanical RF Characteristics United States (FCC) Regulatory Information Canada (ISED) Regulatory Information 3 4 5 5 5 5 6 8 Page 2 of 10 Version History Version 1 August 2020: Initial Release Version 2 September 2020: Including additional required information Version 3 September 2020: Including additional required information Version 4 September 2020: Including additional required information Page 3 of 10 Overview The OEM module is a part of the Mirion Technologies Orion RTLS system. The module utilizes ultra-wideband (UWB) pulses to communicate data and timestamp information to other UWB devices in the system. This information is used to calculate the position and movement of the OEM module. Page 4 of 10 Product Specifications Main System Components Microcontroller:

RF Transceiver:

Sensors:

Indicators:

Operating Voltage:

Operating Temperature:

Storage Temperature:

Nordic nRF52840 MCU BLE Transceiver Decawave DW1000 Ultra-Wideband (UWB) IEEE802.15.4-2011 Accelerometer LED 3.0 - 3.6V (3.3V nom.)

-20C to 65C

-40C to 65C Mechanical Length: 40 mm Width: 20 mm Height: 7.8 mm Weight: 3.4 g RF Characteristics UWB IEEE802.15.4-2011 Channel: 5, PRF 16 MHz Bandwidth (Values in MHz):

Data Rate: 6.81 Mbps Channel: 5, PRF 64 MHz Bandwidth (Values in GHz):

Data Rate: 6.81 Mbps Antenna fM Bandwidth The highest emission peak 10 dB Bandwidth 6544.5 613.3 fM Bandwidth The highest emission peak 10 dB Bandwidth 6644.4 520.5 Manufacturer Model Type Peak Gain (dBi) Mirion Technologies N/A [Embedded]

Planar PCB 1.4 Page 5 of 10 United States (FCC) Regulatory Information FCC ID: 2AWTM-RTLS-OEM001 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The OEM integrator is responsible for compliance testing to Part 15 Subpart B with the module installed and for compliance to any other FCC rules that apply to the host not covered by the module grant of certification. Page 6 of 10 To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following regulations: 1. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:

IMPORTANT: Contains FCC ID: 2AWTM-RTLS-OEM001. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (FCC 15.19). Applicable rules: FCC 15.250 Page 7 of 10 Canada (ISED) Regulatory Information IC: 21847-RTLSOEM001 CAN ICES-3 (B)/NMB-3(B) This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). This Module is labelled with its own IC ID. If the IC ID Certification Number is not visible while installed inside another device, then the device should display the label on it referring to the enclosed module. In that case, the final end product must be labelled in a visible area with the following:

Contains Transmitter Module IC: 21847-RTLSOEM001 OR Contains IC: 21847-RTLSOEM001 Ce module est tiquet avec son propre ID IC. Si le numro de certification IC ID nest pas visible lorsquil est install lintrieur dun autre appareil, lappareil doit afficher ltiquette sur le module de rfrence ci-joint. Dans ce cas, le produit final doit tre tiquet dans un endroit visible par le texte suivant:

Contains Transmitter Module IC: 21847-RTLSOEM001 OR Contains IC: 21847-RTLSOEM001 Page 8 of 10 This radio transmitter (IC:21847-RTLSOEM001) has been approved by ISED Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC:21847-RTLSOEM001) a t approuv par ISED Canada pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal. Let types dantenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. Manufacturer Model Type Peak Gain (dBi) Mirion Technologies Embedded PCB Trace Omnidirectional 1.4 Radiation Exposure Statement:

The device has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091 and ISED Canada RSS-102 for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration dexposition aux radiations:

Le dispositif a t jug conforme aux exigences nonces dans les articles 47 CFR 2.1091 et ISED Canada RSS-102 pour un environnement non contrle. Lantenne(s) utilise pour ce transmetteur doit etre install pour fournir une distance de sparation dau moins 12 mm de toutes les personnes et ne doit pas tre co-localiss ou fonctionner en conjunction avec une autre antenne ou transmetteur. This device is intended only for OEM integrators under the following conditions:

The transmitter module may not be co-located with any other transmitter or antenna. As long as the condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Page 9 of 10 Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:

Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur lmetteur ne seront pas ncessaires. Toutefois, lintgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. Important Note:

configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate Canada authorization. Applicable rules: RSS-210 In the event that these conditions can not be met (for example certain laptop Page 10 of 10

MIRION PROPRIETARY INFORMATION Each manufactured Orion OEM UWB Module will have the following label affixed to the back of the unit:

LETTER OF SIGNATURE AUTHORIZATION July 2, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 2l046 Gentlemen:

This letter authorizes Stan Mushyakov, 5945 Cabot Parkway, Suite 100, Alpharetta, GA 30005, to sign documents before the FCC and ISED on my behalf and Mirion Technologies Inc. This authorization is inclusive of our product currently in review by your office:

Orion OEM UWB Module (FCC ID: 2AWTM-RTLS-OEM001) Under FCC Docket Number 20780 and General Docket Number 80-284 pursuant to Part l5 of FCC Rules and Regulations. Sincerely, Anthony Fallu-Labruyere Director, R&D DMD E&A 13113 Lamanon FRANCE

770-432-2744 770-432-9179 Tel. Fax www.mirion.com Mirion Technologies (MGPI), Inc. 1218A Menlo Drive Atlanta, Georgia 300318 9 September 2020 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request FCC ID: 2AWTM-RTLS-OEM001 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, Mirion Technologies hereby requests permanent confidential treatment of information accompanying this application as outlined below:

Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, David Jarrow Sr. Director of Strategic Programs DJ/dj

Modular Approval Request Date: July 2, 2020 Federal Communications Commission Authorization and Evaluation Division RE: FCC ID:

2AWTM-RTLS-OEM001 The following attestation addresses the requirements to support modular approval:

Yes YES YES YES YES Modular Approval Requirement The radio elements must have the radio frequency circuitry shielded. Physical/discrete and tuning capacitors may be located external to the shield but must be on the module assembly. The module must have buffered modulation/data inputs to ensure that the device will comply with the Part 15 requirements with any type of input signal. The module must contain power supply regulation on the module. The module must contain a permanently-attached antenna, or contain a unique antenna connector, and be marketed or operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). The module must demonstrate compliance in a stand-alone configuration. YES The module must be labelled with its permanently fixed YES No FCC ID label, or use an electronic display. Modular Approval Requirement The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements. Yes YES The module must comply with RF Exposure requirements YES Sincerely, ____________________________ Signature ____________________________ Name No __________________________ Date __________________________ Title David Jarrow Director of Operaitons 7 October 2020