FCC ID: P4Q-N664B Connected Digital Recorder

V. For more information Caring for your device l Taking good care of your device will ensure trouble-free operation and reduce the risk of damage. l Keep your device away from excessive moisture and extreme temperatures. l Avoid exposing your device to direct sunlight or strong ultraviolet light for extended periods of time. l Do not place anything on top of your device or drop objects on your device. l Do not drop your device or subject it to severe shock. l Do not subject your device to sudden and severe temperature changes. This could cause moisture condensation inside the unit, which could damage your device. In the event of moisture condensation, allow the device to dry out completely before use. l Never attempt to disassemble, repair or make any modifications to your device. Disassembling, modifying or any attempt to repair could cause damage to your device, may inflict bodily harm or damage to property and will void any warranty. l Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your device, its parts or accessories. l To discourage theft do not leave the device and accessories in plain view in an unattended vehicle. l Overheating may damage the device. About GPS l GPS (Freq=1575.42MHZ) is operated by the United States government, which is solely responsible for the performance of GPS. Any change to the GPS system can affect the accuracy of all GPS equipment. l GPS satellite signals cannot pass through solid materials

(except glass). When you are inside a tunnel or building, GPS positioning is not available. Signal reception can be affected by situations such as bad weather or dense overhead obstacles (e.g. trees, tunnels, viaducts and tall buildings). l The GPS positioning data is for reference only. Regulatory Information For regulatory identification purposes, the device is assigned a model number of N664 / Dashcam. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Connect the equipment into an outlet on a circuit different Increase the separation between the equipment and receiver. from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : 1) Lappareil ne doit pas produire de brouillage; 2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated with minimum distance 30 cm between the radiator and your body. USA Contact Information Magellan 279 E Arrow Highway San Dimas, CA 91773 USA

+1 909-394-5000 http://www.magellangps.com CE Products with the CE marking comply with Radio Equipment Directive (Directive 2014/53/EU) - issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Standards:

EN 301 489-1 V2.2.3 (2019-11) EN 301 489-3 V2.1.1 (2019-03) EN 301 489-17 V3.1.1 (2017-02) EN 301 489-19 V2.1.1 (2019-04) Draft EN 301 489-52 V1.1.0 (2016-11) EN 55032:2015+AC:2016, Class B EN 55035:2017 EN 50498:2010 ISO 7637-2:2004 EN 300 328 V2.2.2 EN 300 440 V2.1.1; 2017 IEC60950-1(ed.2); am1; am2 IEC62368-1:2014 (EN62368-1:2014/A11:2017) The manufacturer cannot be held responsible for modifications made by the User and the consequences thereof, which may alter the conformity of the product with the CE Marking. Declaration of conformity Hereby, MiTAC declares that this N664 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Maximum power for each band LTE-FDD: B1/ B2/ B3/ B4/ B5/ B7/ B8/ B20/ B28 (25dBm) LTE-TDD: B38/ B39/ B40/ B41 (25dBm) WCDMA: B1/ B2/ B4/ B5/ B8 (25dBm) GSM/EDGE: 850/900/1800/1900MHz (32dBm) About WIFI Frequency: 2412 2472MHZ Max. power = 18dbm About BT Max. power = 11dBm WEEE This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE 2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point. N664DashcamInstallation GuideI.What's in the BoxDash cam with front and interior-facing camerasRear mounting plate with adhesive tapeTop coverCable capY-cableOBD-II cable10-pin to open end cableRear recording camera with cable (selected models only)II.Product Overview1Reset button9Emergency recording indicator/button2SIM card slotqWIFI/mobile broadband indicator3MicroSD slotwInfrared illuminator (x4)4Rear camera connectoreInterior-facing camera5Charging/data portrSpeaker6NFC sensortMounting slot (x3)7Camera locking screw (x2)yFront-facing camera8Microphone (x2)III.Device InstallationPrecautions and noticesFor your own safety, do not operate the controls of the product while driving. Using this product does not exempt the driver from taking full responsibility for his/her driving behaviour, which includes observing all traffic rules and safety regulations.Make sure the dash cam is positioned in a way that does not obstruct the drivers view or airbag deployment.Make sure that no object is blocking the camera lens and no reflective material appears near the lens. Please keep the lens clean.Video quality may be degraded if the vehicles windscreen is tinted.If the cars windscreen is tinted with a reflective coating, its surface may be athermic and impact GPS reception. In this instance, please mount the device in a clear area.The device will automatically calibrate its G-sensor during start-up. Always turn on the device after it is mounted in place to avoid G-sensor malfunction.Mounting the dash camThe dash cam should be placed near the rear-view mirror to ensure the highest video quality, but never position the device where the drivers field of vision is blocked.When adjusting the dash cams viewing angle, make sure the vehicle is parked on level ground and the cameras view is parallel to the ground. The ground to sky ratio should be approximately 6 to 4.Note:lCleaning the windscreen with rubbing alcohol before mounting the dash cam is highly recommended.lThe double-sided adhesive tape can be replaced if it is no longer adhering to the windscreen properly.SIM and memory cardsA MicroSD card (up to 256GB in capacity) and a Nano SIM card must be inserted prior to mounting the dash cam on the windscreen.It is very important to use a MicroSD card specifically designed to be used in dash cameras. It ensures the card will be more reliable and last longer; the wrong type of card has a greater chance of failing, even after a short period of time.To insert a card, hold each card by the edges and gently insert it into the slot as shown in the illustration. To remove a card, gently push the top edge of the card inwards to release it and pull it out of the slot.1.Route the Y-cable inside the vehicle, leaving the main connector exposed at where the dash cam is to be installed on the windscreen and the other end going toward the vehicle's OBD-II port.2.Peel the film off from the back of the rear plate.3.Affix the rear plate securely onto the windscreen.4.Attach the dash cam to the rear plate by matching the positions of the three mounting holes on the back of the camera with the hooks on the rear plate. Slide the dash cam to the left to lock it in place.5.Connect the main connector to the dash cam. If your product includes a rear recording camera, connect the rear camera cable to the mini-USB port as shown.6.Attach the top cover to the dash cam and tighten the screw with an M2 hex key.7.Cover exposed cables coming out the dash cam with the cable cap. The rubber cap can be trimmed to desired length with a pair of scissors.8.Plug the OBD-II connector into the vehicle's OBD-II port and use the following table to connect the colour-coded open wires:ColourConnectionRedAccessory (ACC)OrangeReverseYellowInputGreenRS232 TX Out (to vehicle)BlueSpeed pulsePurpleInputBrownInputGreyOutputBlackGroundWhiteRS232 TX In (to dash cam)The following is a complete connection diagram:9.Adjust the viewing angle of the front and interior facing cameras by loosening the corresponding locking screw with an M2 hex key. Tighten the locking screws once the viewing angles are set.Rear recording cameraA rear recording camera is included with selected models. Before installing the rear recording camera, please wipe the surface clean with rubbing alcohol. Select a suitable location for mounting the rear recording camera so that the driver's field of vision is not obscured.1 Camera lens2 Mounting base3 Micro-USB portOne end of the rear camera cable should already be connected to the dash cam (see step No. 5 of the installation instructions). Once the rear camera is mounted in the appropriate location, connect the other end of the cable to the rear camera's micro-USB port.IV.LED IndicatorsRecording/emergency recording LED:BehaviourIndicationRed, always onNormal recording in progressRed, blinking slowlyEmergency recording in progressRed, blinking rapidlyMemory card errorWIFI/mobile broadband LED:BehaviourIndicationCyanSystem initializingGreen, always onWIFI connectedBlue, always onMobile broadband connectedBlue, blinkingMobile broadband disconnected

PA ICES-003 Model: N664 FCC ID: P4Q-N664B eae Ma aces

[emer elem or) Contains IC: 10224A-2019SC600NA ene PIN: 242N66400007 ROO one ete be Degree ana ey

| Ne eee

| E=| EROAD Cc eee ieted em or) gee aC Cerny else}

IC: 2420C-N664B He ere meen PIN: 242N66400005 ROO CAUTION: Only use cables shipped with this unit (see guide)

Mitac Digital Technology Corporation A4F., No. 1, R&D Road 2, Hsinchu Science Park, Hsinchu 30076, Taiwan Tel: 886-3-396-1888 ; Fax: +886-3-327-6323 Date: September 9, 2020 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for Confidentiality FCC ID: P4Q-N664B To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Part List Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Ruey-Yuai Chen Ruey-Yuan.Chen@mic.com.tw

Mitac Digital Technology Corporation 4F., No. 1, R&D Road 2, Hsinchu Science Park, Hsinchu 30076, Taiwan Tel: 886-3-396-1888 ; Fax: +886-3-327-6323 Date: September 9, 2020 To whom it may concern, Please be notified that |, Ruey-Yuan Chen, have designated Jones Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jones Tsai in Sporton International Inc. on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. This authorization is limited to the product of as following:

FCC ID: P4Q-N664B If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Sincerely yours, Ruey-Yuan Chen Ruey-Yuan.Chen@mic.com.tw