FCC ID: P4Q-N693B Gemini SE

I. Product Overview Installation Guide N693 1 Cap sensor 2 MicroSD slot q Emergency recording indicator/button w WIFI/mobile broadband indicator e Infrared illuminator (x4) r Interior-facing camera t Speaker 3 SIM card slot 4 Reset button 5 Charging/data port 6 Rear camera connector y Mounting slot (x3) 7 NFC sensor 8 Camera locking screw u Front-facing camera i Antenna 05/2021

(x2) 9 Microphone (x2) C. Affix the fleet cam D. Adjust camera viewing angle Note:

l Cleaning the windshield with rubbing alcohol before mounting the fleet cam is highly recommended. l The double-sided adhesive tape can be replaced if it is no longer adhering to the windshield properly. l The fleet cam should be placed near the rear-view mirror to ensure the highest video quality, but never position the device where the drivers field of vision is blocked. 1. Peel the film off from the back of the rear plate and affix the rear plate securely onto the windshield. 2. Attach the fleet cam to the rear plate by matching the positions of the three mounting holes on the back of the camera with the hooks on the rear plate. Slide the fleet cam to the left to lock it in place. 3. Connect the main connector to the fleet cam. 4. Attach the top cover to the fleet cam and tighten the screw with an M2 hex key. 5. Cover exposed cable coming out the fleet cam with the cable cap. The rubber cap can be trimmed to desired length with a pair of scissors. Peel the 3M tape off from the back of the cable cap to adhere it to the windshield. 3M tape 1. Activate the fleet cam's hotspot function by pressing the emergency recording button for three seconds. 2. Use a portable device such as a smartphone or tablet to connect to the hotspot by scanning the QR code (containing network SSID and password info) inside the box. 3. Open the live view page on the portable device. 4. Loosen the camera locking screw with an M2 hex key and adjust the viewing angle using the live view displayed on the screen of the portable device. Note: When adjusting the fleet cams viewing angle, make sure the vehicle is parked on level ground and the cameras view is parallel to the ground. The ground to sky ratio should be close to a 50/50 split. 5. Tighten the locking screw to lock the camera position once the angle is set. 6. If your system also includes an interior-facing camera, repeat steps 4 and 5 to adjust its viewing angle. Buttons on the webpage can be used to switch to different camera views. E. Install rear recording camera (optional accessory) A rear recording camera can be purchased separately as an optional accessory. Before installing the rear recording camera, please wipe the surface clean with rubbing alcohol. Select a suitable location for mounting the rear recording camera so that the driver's field of vision is not obscured. 1 Camera lens 2 Mounting base 3 Micro-USB port II. Device Installation Precautions and notices This device has been tested and certified to meet the applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. For your own safety, do not operate the controls of the product while driving. Using this product does not exempt the driver from taking full responsibility for his/her driving behavior, which includes observing all traffic rules and safety regulations. Make sure the fleet cam is positioned in a way that does not obstruct the drivers view or airbag deployment. Make sure that no object is blocking the camera lens and no reflective material appears near the lens. Please keep the lens clean. Video quality may be degraded if the vehicles windshield is tinted. If the cars windshield is tinted with a reflective coating, its surface may be athermic and impact GPS reception. In this instance, please mount the device in a clear area. The device will automatically calibrate its G-sensor during start-up. Always turn on the device after it is mounted in place to avoid G-sensor malfunction. Installation procedure A. Insert memory/SIM card A MicroSD card (up to 256GB in capacity) and a Nano SIM card must be inserted prior to mounting the fleet cam on the windshield. It is very important to use a MicroSD card specifically designed to be used in fleet cameras. It ensures the card will be more reliable and last longer; the wrong type of card has a greater chance of failing, even after a short period of time. Plug the micro-USB connector of the rear recording camera cable into the rear cam and the mini-USB connector into the fleet cam (please note that you will have to remove the cable cap and top cover in order to access the fleet cam's mini-USB port located next to the charging/data port). Use the same method described in the previous section to adjust the camera's viewing angle. F. Complete the installation/using the device Before using the fleet cam to record videos, peel off the protective film covering the camera lens. The fleet cam will automatically turn on once the vehicle engine is started and the system will automatically begin continuous recording after a few seconds. During continuous recording, if a sudden event (such as running over a road bump, vehicle collision, high-speed driving, or making a sharp turn) has been detected, the G-sensor will prompt the fleet cam to record the event. You can also press the emergency recording button to record a video manually while continuous recording is in progress. To insert a card, hold each card by the edges and gently insert it into the slot as shown in the illustration. To remove a card, gently push the top edge of the card inwards to release it and pull it out of the slot. B. Route the main cable Route the main cable inside the vehicle, leaving the main connector exposed at where the fleet cam is to be installed on the windshield and the other end going toward the vehicle's power source. Plug the OBD-II connector into the vehicle's OBD-II port and use the table below to connect the color-coded wires:

Color Connection Red Orange Yellow Green Blue Purple Brown Grey Black White Accessory (ACC) Reverse Input RS232 TX Out (to vehicle) Speed pulse Input Input Output Ground RS232 TX In (to fleet cam) III. LED Indicators Recording/emergency recording LED:

Behavior Indication Red, always on Red, blinking slowly Red, blinking rapidly Normal recording in progress Emergency recording in progress Memory card error WIFI/mobile broadband LED:

Behavior Cyan Green, always on Blue, always on Blue, blinking Indication System initializing WIFI connected Mobile broadband connected Mobile broadband disconnected IV. Hardware Reset Occasionally you may need to perform a hardware reset when the fleet cam stops responding. The top cover must be removed in order to access the device's reset button. Use a sharp object

(such as a straightened paper clip) to press the reset button. V. Additional Information Caring for your device Taking good care of your device will ensure trouble-free operation and reduce the risk of damage. Keep your device away from excessive moisture and extreme temperatures. Avoid exposing your device to direct sunlight or strong ultraviolet light for extended periods of time. Do not place anything on top of your device or drop objects on your device. Do not drop your device or subject it to severe shock. Do not subject your device to sudden and severe temperature changes. This causes moisture condensation inside the unit which could damage your device. In the event of moisture condensation, allow the device to dry out completely before use. Never attempt to disassemble, repair, or modify your device. Disassembling, modifying or attempting to repair on your own may damage your device, inflict bodily harm or property damage and will void any warranty. Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your device, its parts or accessories. Overheating may damage the device. About GPS GPS (Freq=1575.42MHz) is operated by the United States government, who is solely responsible for the system's performance. Any change to the GPS system can affect the accuracy of all GPS equipment. GPS satellite signals cannot pass through solid materials

(except glass). GPS positioning is unavailable when you are inside a tunnel or building. Signal reception can be affected by conditions such as poor weather or dense overhead obstacles

(e.g. trees, tunnels, viaducts and tall buildings). GPS positioning data is for reference only. Regulatory Information For regulatory identification purposes, the device is assigned a model number of N693. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or a radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : 1) Lappareil ne doit pas produire de brouillage; 2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated with minimum distance 30 cm between the radiator and your body. Caution: Exposure to Radio Frequency Radiation 1. To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-

located or operating in conjunction with any other antenna or transmitter. 2. To comply with RSS 102 RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Attention: Exposition au rayonnement radiofrquence 1. Pour se conformer aux exigences de conformit RF canadienne lexposition, cet appareil et son antenne ne doivent pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. 2. Pour se conformer aux exigences de conformit CNR 102 RF exposition, une distance de sparation d'au moins 20cm doit tre maintenue entre lantenne de cet appareil et toutes les personnes. Declaration of conformity Hereby, MiTAC declares that the N693 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Maximum power for each band LTE-FDD: B1/ B2/ B3/ B4/ B5/ B7/ B8/ B20/ B28 (25dBm) LTE-TDD: B38/ B39/ B40/ B41 (25dBm) WCDMA: B1/ B2/ B4/ B5/ B8 (25dBm) GSM/EDGE: 850/900/1800/1900MHz (32dBm) About WIFI Frequency: 2412 2472MHZ Max. power = 18dbm About BT Max. power = 11dBm WEEE This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE 2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.

Rating label location cy

I Pantone Black C Model : N693 FCC ID:P4Q-N693B 1C:2420C-N693B yA lol SSSeleK) Model: N693 Input: 12/24V ==1A(MAX) FCC ID: P4Q-N693B Contains FCC ID: XMR2019SC600NA IC: 2420C-N693B Contains IC: 10224A-2019SC600NA P/N: 242N69300001 ROO Tecenery Caution: Only use the specified cable for the connection (see user's manual)

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name MiTAC Digital Technology Corporation 4F., No. 1, R&D Road 2, Hsinchu Science Park, Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Ruey-Yuan Chen P4Q N693B ruey-yuan.chen@mic.com.tw 886-3-396-1888 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date:2020/05/24 Print Name:

Title:

Ruey-Yuan Chen Director Applicant Declaration Rev:0.0

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Declaration Rev:0.0

<MiTAC Digital Technology Corporation>

To:

From: MiTAC Digital Technology Corporation SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States 4F., No. 1, R&D Road 2, Hsinchu Science Park, Confidentiality Request regarding application for FCC ID P4Q-N693B Hsinchu 30076, Taiwan, R.O.C. Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Printed Name (on file with the FCC associated with the Grantee Code) Ruey-Yuan Chen Title Director Company Name MiTAC Digital Technology Corporation

<MiTAC Digital Technology Corporation>

TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Date: May 24, 2021 Regarding: FCC ID: P4Q-N693B To whom it may concern:

We, the undersigned, hereby authorize SGS Taiwan Ltd. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Traxxas LP. This authorization is valid until further written notice from the applicant. Name (Printed): Ruey-Yuan Chen Title:Director Signature:

On behalf of Company: MiTAC Digital Technology Corporation Telephone: 886-3-396-1888