FCC ID: 2AAOY-Y-HSB-X Bluetooth Speaker

INSTALLATION INSTRUCTIONS ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720 THANK YOU FOR CHOOSING KURYAKYN!

Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation, use, and care of this product. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN MINOR OR MODERATE POTENTIAL INJURY. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN MAY NEGATIVELY AFFECT PRODUCT PERFORMANCE AND FUNCTIONALITY OR DAMAGE THE PRODUCT ITSELF OR THE PRODUCT TO WHICH IT IS BEING ATTACHED. ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:

1 2 2 2 2 2 1 1 Road Thunder Sound Bar Plus with Wire Harness Sound Bar Mounting Clamps 7/8 Clamps 1 Clamps 1-1/8 Clamps 1-1/4 Clamps USB Rubber Plug Seal Transparent Film ROAD THUNDER SOUND BAR PLUS 1 Hardware Kit, containing:

2 M6-1.0 X 35MM Button Head Hex Screws 2 M6-1.0 Lock Nut w/Washers 2 M6-1.0 X 11MM Cap Screw Hex Drive 2 M6 Split Washers 2 M4-0.7 X 10MM Set Screws 1 1 1 4 2MM Allen Wrench 10 Amp Mini Fuse T-Tap Quick Connect Female Cable Ties 2MM ALLEN WRENCH SOUND BAR MOUNTING CLAMPS TRASNPARENT FILM WIRE HARNESS USB RUBBER PLUG SEAL CABLE TIES 10 AMP FUSE M6-1 X 35MM BHHS M6-1 LOCK NUT M6-1 X 11MM CSHD SPLIT WASHERS SET SCREWS T-TAP QUICK CONNECTS 7/8 CLAMP 1 CLAMP 1-1/8 CLAMP 1-1/4 CLAMP YOU WILL ALSO NEED:

Metric Hex, Allen wrenches, pliers CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. THESE INSTALLATION INSTRUCTIONS CONTAIN IMPORTANT INFORMATION. ENSURE THE END USER RECEIVES THIS COPY AND IS AWARE OF ITS IMPORTANCE FOR FUTURE USE. WHEN CONNECTING POWER AND GROUND WIRES ENSURE THAT THE RED POWER WIRE IS FUSED AT THE POINT WHERE IT IS CONNECTED TO THE VEHICLES BATTERY. FAILURE TO DO SO CAN RESULT IN DAMAGE TO THE VEHICLE IF A SHORT CIRCUIT DEVELOPS BETWEEN THE VEHICLE CONNECTION POINT AND THE PRODUCT. PAGE 1 302720 DPF-MRK-003 REV B 8/10/18 KURYA KYN.C OM 866 277 9598 | INFO@KURYAKYN.COM 454 COUNTY ROAD VV SOMERSET, WI 54025

-CONTINUED-

INTRODUCTION FEATURES Thank you for purchasing this Kuryakyn Road Thunder Sound Bar Plus by MTX that is designed to work with most Bluetooth enabled devices including iPhone and Android smartphones and tablets. This easy to install and use, all in one unit is capable of transforming your Bluetooth enabled mobile device into the center of your vehicles audio system. It is designed to mount on a variety of bars between 78 and 1-14. Congratulations and enjoy the ultimate audio experience!

Universal mounting clamps fit bars between 78 and 1-14 Power, ground, ignition wire, and 12v trigger output included for easy installation Automated Bluetooth pairing via NFC 1.0 Amp USB charging port Two 2 x 3 full range speakers and four 1 high frequency tweeters All-weather construction for use in almost any environment Integrated Bluetooth receiver Auxiliary input for connecting devices via 3.5mm cable Auxiliary output for connecting an external amplifier or additional sound bar via 3.5mm cable INSTALLATION The Road Thunder Sound Bar Plus can be used with any 12-volt battery and can be mounted to a variety of bars using the included hardware. The unit has four wires in its wiring pigtail. The red wire, hot, should be directly connected to the vehicles positive battery terminal. The black wire, ground, should be connected directly to the vehicles chassis where paint has been removed or the negative terminal on the battery. Use the included T-Tap Quick Connect Female connector and install directly onto the ACC/Key ignition wire on the motorcycle using a pair of pliers. Connect the Quick Con-

nect Male connector, located on the orange wire, and the T-Tap Quick Connect Female together. The blue wire, optional output, can be used to turn on additional amplifiers. Choose the correct size strap clamp for the handlebars. SCENARIO 1 - MOUNT CLAMPS TO HANDLEBAR FIRST, THEN INSTALL SOUND BAR. The unit features fully adjustable clamps for mounting to bars between 78 and 1-14. The clamps can be used to mount to many styles of handlebar and roll bar systems. The included brackets are versatile, so mounting to angled bars is possible. Note: placing the transparent film between the strap clamp and handlebar will reduce the possibility of scratching the handlebars during installation. Assemble mid-section to bottom bracket using included 5mm Allen screw and 10mm hex nut. Ensure that the spacing between the brackets is between 3 and 6.75. Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them. Rotate the sound bar so the speakers are directed at the riders head. Tighten the 5mm Allen screws to lock the sound bar in place. Tighten the 2mm set screws. Connect wires to power, ground, and ignition. PAGE 2 302720 DPF-MRK-003 REV B 8/10/18ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK2720866 277 9598 | INFO@KURYAKYN.COM454 COUNTY ROAD VV SOMERSET, WI 54025KURYAKYN.COMINSTALLATION INSTRUCTIONS-CONTINUED-

INSTALLATION SCENARIO 2 - INSTALL SOUND BAR, THEN MOUNTS CLAMPS TO HANDLEBAR. Choose the correct size strap clamp for the handlebars. Note: Placing the transparent film between the strap clamp and handlebar will reduce the possibility of scratching the handlebars during installation. Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them. Ensure that the spacing between the brackets is between 3 and 6.75. Assemble mid-section to bottom bracket using included 5mm Allen Screw and 10mm Hex Nut. Rotate the sound bar so the speakers are directed at the riders head. Tighten the 5mm Allen Screws to lock the sound bar in place. Tighten the 2mm Set Screws. Connect wires to power, ground, and ignition. ORIENTATION EXAMPLES PAGE 3 302720 DPF-MRK-003 REV B 8/10/18ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK2720866 277 9598 | INFO@KURYAKYN.COM454 COUNTY ROAD VV SOMERSET, WI 54025KURYAKYN.COMINSTALLATION INSTRUCTIONS-CONTINUED-

ELECTRICAL OPERATION STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 Tap the Power button to turn the unit on. (Power, Ground, and Ignition wire need to be connected to a 12V power source.) Tap the Power button to switch modes between Bluetooth and AUX. Hold the Power button for 2 seconds to turn the unit Off. The integrated fuse and ring terminals allow for easy wire connection to a 12V power source. The remote turn on (blue wire) only operates when the unit is powered on. Note: The indicator light will illuminate Blue when in Bluetooth mode and Green when in AUX mode. OPERATION FOLLOW THESE STEPS TO UTILIZE THE BLUETOOTH FUNCTIONALITY USING A BLUETOOTH ENABLED DEVICE:

Power the unit On by tapping the Power button once. Select Bluetooth by tapping the Power button until it blinks Blue. Select MTX Sound Bar from the menu on your Bluetooth enabled device. The unit will power on in Bluetooth mode first when it is turned on by tapping. If the Ignition wire is disconnected, (vehicle is turned off and then turned on) the unit will revert back to the previous Bluetooth or AUX setting. Choose Pair when prompted. Once Paired the unit will be able to play audio from your Bluetooth device. The front panel control buttons will control track forward/back and volume up/

down in this mode. The Play/Pause button will mute the output and the LED indicator will blink Blue when in Mute mode. FOLLOW THESE STEPS TO UTILIZE BLUETOOTH IN A NFC (NEAR FIELD COMMUNICATION) ENABLED DEVICE:

Power the unit On by tapping the Power button once. Select Bluetooth by tapping the Power button until it blinks Blue. Tap the NFC enabled device on the (left) side of the enclosure (marked by NFC label). Choose Pair when prompted. Once Paired the unit will be able to play audio from your NFC device. FOLLOW THESE STEPS TO UTILIZE AN AUXILIARY INPUT DEVICE:

Power the unit On by tapping the Power button once. Select Auxiliary by tapping the Power button until it blinks Green. Connect an audio device to the AUX input using the Green 3.5mm input on the side of the unit. The LED will illuminate Green, and will blink Green when in mute mode. The front panel control buttons will adjust the Volume up/down in this mode. The Play/Pause button will mute the audio output and the LED indicator will blink Green when in Mute mode. USING THE AUXILIARY OUTPUT. OUTPUT MARKED ON (LEFT) SIDE OF ENCLOSURE. Auxiliary out is a variable output that allows connection to a secondary audio device, whether it is an external amplifier connected to speakers or subwoofer. STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 1 STEP 2 STEP 3 STEP 1 PAGE 4 302720 DPF-MRK-003 REV B 8/10/18ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK2720866 277 9598 | INFO@KURYAKYN.COM454 COUNTY ROAD VV SOMERSET, WI 54025KURYAKYN.COMINSTALLATION INSTRUCTIONS-CONTINUED-

STEP 2 STEP 3 STEP 1 STEP 2 The Road Thunder Sound Bar Plus can be used with a second Road Thunder Sound Bar Plus unit. For the best audio performance, the second unit connected via Auxiliary should have the volume set to the max. The blue wire on the wire harness can be used as a remote turn on for the second audio device. CONTROLLING THE VOLUME The LED indicator light will blink in both Bluetooth and AUX modes at max volume. USB CHARGING PORT Place USB rubber plug seal onto desired USB cord. Plug USB cord into USB port located on the side of the Road Thunder Sound Bar Plus. This is a charging port only, it is NOT an audio input. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. LIMITED WARRANTY Kuryakyn warrants that any Kuryakyn products sold hereunder, shall be free of defects in materials & workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions:

1. Kuryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s). 2. The product must be properly installed, maintained & operated under normal conditions. 3. Kuryakyn shall not be liable for any consequential & incidental damages, including labor & paint, resulting from failure of a Kuryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breach of contract or duty between Kuryakyn & a customer. 4. Kuryakyn products are often intended for use in specific applications. Kuryakyn makes no warranty if a Kuryakyn product is used in applications other than intended. 5. Kuryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.s contained in components of Kuryakyn products will be warranted for defects in materials & workmanship for 3 years from the date of purchase whereas all other components shall be warranted for one (1) year. 6. All warranty claims must be directed to the place of purchase. Merchandise sold through internet auction sites or any other unauthorized reseller shall not carry a Kuryakyn warranty. If unsure, please contact the place of purchase to verify they are an authorized Kuryakyn reseller. RETURN POLICY Merchandise determined to be defective may be returned up to one year from the date of purchase. Returns must be processed through original seller. Returned merchandise for any other reason other than warranty claims must be in like new condition & subject to a 20% restocking fee. All returns are subject to inspection for determination of full or partial credit. Any returned part that shows evidence of being used or installed contrary to manufacturers instructions, &/or subjected to improper handling, packaging or return shipping by the customer, will not be eligible for exchange, refund or warranty consideration. All returned electrical items will be inspected & tested. If electrical item is deemed functional, no credit will be issued & item will be returned. All sales are final on discontinued or closeout merchandise. 2015 KURYAKYN HOLDINGS, LLC ALL RIGHTS RESERVED KURYAKYN, KURYAKYN K logo and the marks appearing on this instruction sheet are registered and common law trademarks of Kuryakyn Holdings except noted third-party trademarks. A full listing of trademarks and trademark registrations owned by Kuryakyn Holdings can be found at www.kuryakyn.com/legal-notice. Emissions Notice: The California Air Resources Board (CARB) does not permit the use of aftermarket emission-related parts(s) that alter the performance of OEM emission-related devices unless CARB has issued an Executive Order, other than on racing vehicles on closed courses. Check your local laws and manufacturers information. Listed Manufacturers and product model names are for reference only. All product and company names are trademarks or registered trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them. All specifications are subject to change without notice. For additional information on third-party product and company names, please consult our Web page at www.kuryakyn.com/legal-notice PAGE 5 302720 DPF-MRK-003 REV B 8/10/18ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK2720866 277 9598 | INFO@KURYAKYN.COM454 COUNTY ROAD VV SOMERSET, WI 54025KURYAKYN.COMINSTALLATION INSTRUCTIONS

THANK YOU FOR CHOOSING KURYAKYN!

Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation, use, and care of this product. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN MINOR OR MODERATE POTENTIAL INJURY. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN MAY NEGATIVELY AFFECT PRODUCT PERFORMANCE AND FUNCTIONALITY OR DAMAGE THE PRODUCT ITSELF OR THE PRODUCT TO WHICH IT IS BEING ATTACHED. ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:

Road Thunder Sound Bar Plus with Wire Harness 1 1 2 2 2 2 2 2 1 1 Sound Bar Mounting Clamps 7/8 Clamps 1 Clamps 1-1/8 Clamps 1-1/4 Clamps 1-1/2 Clamps USB Rubber Plug Seal Transparent Film ROAD THUNDER SOUND BAR PLUS Hardware Kit, containing:

2 M6-1.0 X 35MM Button Head Hex Screws 2 M6-1.0 Lock Nut w/Washers 2 M6-1.0 X 11MM Cap Screw Hex Drive 2 M6 Split Washers 2 M4-0.7 X 10MM Set Screws 1 2MM Allen Wrench 1 7.5 Amp Mini Fuse (Red Power Wire) 1 2 Amp Mini Fuse (Orange ACC/Key Wire) 1 T-Tap Quick Connect Female 4 Cable Ties 2MM ALLEN WRENCH SOUND BAR MOUNTING CLAMPS TRASNPARENT FILM WIRE HARNESS CABLE TIES USB RUBBER PLUG SEAL 7.5 AMP FUSE 2 AMP FUSE M6-1 X 35MM BHHS M6-1 LOCK NUT M6-1 X 11MM CSHD SPLIT SET WASHERS SCREWS T-TAP QUICK CONNECTS YOU WILL ALSO NEED:

Metric Hex, Allen wrenches, pliers CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. THESE INSTALLATION INSTRUCTIONS CONTAIN IMPORTANT INFORMATION. ENSURE THE END USER RECEIVES THIS COPY AND IS AWARE OF ITS IMPORTANCE FOR FUTURE USE. WHEN CONNECTING POWER AND GROUND WIRES ENSURE THAT THE RED POWER WIRE IS FUSED AT THE POINT WHERE IT IS CONNECTED TO THE VEHICLES BATTERY. FAILURE TO DO SO CAN RESULT IN DAMAGE TO THE VEHICLE IF A SHORT CIRCUIT DEVELOPS BETWEEN THE VEHICLE CONNECTION POINT AND THE PRODUCT. 7/8 CLAMP 1 CLAMP 1-1/8 CLAMP 1-1/4 CLAMP 1-1/2 CLAMP PAGE 1 302720 DPF-MRK-003 REV D 03/12/20 INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D BA R P LU S B Y M T X, SAT I N B L A C K 2720 KURYAKYN.COM 866 277 9598 | INFO@KURYAKYN.COM 454 COUNTY ROAD VV SOMERSET, WI 54025

-CONTINUED-

INTRODUCTION Thank you for purchasing this Kuryakyn Road Thunder Sound Bar Plus by MTX that is designed to work with most Bluetooth enabled devices including iPhone and Android smartphones and tablets. This easy to install and use, all in one unit is capable of transforming your Bluetooth enabled mobile device into the center of your vehicles audio system. It is designed to mount on a variety of bars between 7 8 and 1-1 2. Congratulations and enjoy the ultimate audio experience!

FEATURES Two 2 x 3 full range speakers and four 1 high frequency tweeters All-weather construction for use in almost any environment Integrated Bluetooth receiver Auxiliary input for connecting devices via 3.5mm cable Auxiliary output for connecting an external amplifier or additional sound bar via 3.5mm cable INSTALLATION Universal mounting clamps fit bars between 7 8 and 1-1 2 Power, ground, ignition wire, and 12v trigger output included for easy installation Automated Bluetooth pairing via NFC 1.0 Amp USB charging port The Road Thunder Sound Bar Plus can be used with any 12-volt battery and can be mounted to a variety of bars using the included hardware. The unit has four wires in its wiring pigtail. The red wire, hot, should be directly connected to the vehicles positive battery terminal. The black wire, ground, should be connected directly to the vehicles chassis where paint has been removed or the negative terminal on the battery. Use the included T-Tap Quick Connect Female connector and install directly onto the ACC/Key ignition wire on the motorcycle using a pair of pliers. Connect the Quick Connect Male connector, located on the orange wire, and the T-Tap Quick Connect Female together. The blue wire, optional output, can be used to turn on additional amplifiers. The unit features fully adjustable clamps for mounting to bars between 7 8 and 1-1 2. The clamps can be used to mount to many styles of handlebar and roll bar systems. The included brackets are versatile, so mounting to angled bars is possible. SCENARIO 1 - MOUNT CLAMPS TO HANDLEBAR FIRST, THEN INSTALL SOUND BAR. Choose the correct size strap clamp for the handlebars. Note: placing the transparent film between the strap clamp and handlebar will reduce the possibility of scratching the handlebars during installation. Assemble mid-section to bottom bracket using included 5mm Allen screw and 10mm hex nut. Ensure that the spacing between the brackets is between 3 and 6.75. Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them. Rotate the sound bar so the speakers are directed at the riders head. Tighten the 5mm Allen screws to lock the sound bar in place. Tighten the 2mm set screws. Connect wires to power, ground, and ignition. INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D BA R P LU S B Y M T X, SAT I N B L A C K 2720 PAGE 2 302720 DPF-MRK-003 REV D 03/12/20 KURYAKYN.COM 866 277 9598 | INFO@KURYAKYN.COM 454 COUNTY ROAD VV SOMERSET, WI 54025

-CONTINUED-

INSTALLATION SCENARIO 2 - INSTALL SOUND BAR, THEN MOUNTS CLAMPS TO HANDLEBAR. Choose the correct size strap clamp for the handlebars. Note: Placing the transparent film between the strap clamp and handlebar will reduce the possibility of scratching the handlebars during installation. Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them. Ensure that the spacing between the brackets is between 3 and 6.75. Assemble mid-section to bottom bracket using included 5mm Allen Screw and 10mm Hex Nut. Rotate the sound bar so the speakers are directed at the riders head. Tighten the 5mm Allen Screws to lock the sound bar in place. Tighten the 2mm Set Screws. Connect wires to power, ground, and ignition. ORIENTATION EXAMPLES PAGE 3 302720 DPF-MRK-003 REV D 03/12/20 INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D BA R P LU S B Y M T X, SAT I N B L A C K 2720 KURYAKYN.COM 866 277 9598 | INFO@KURYAKYN.COM 454 COUNTY ROAD VV SOMERSET, WI 54025 STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 1 STEP 2 STEP 3

-CONTINUED-

ELECTRICAL OPERATION Tap the Power button to turn the unit on. (Power, Ground, and Ignition wire need to be connected to a 12V power source.) Tap the Power button to switch modes between Bluetooth and AUX. Hold the Power button for 2 seconds to turn the unit Off. The integrated fuse and ring terminals allow for easy wire connection to a 12V power source. The remote turn on (blue wire) only operates when the unit is powered on. Note: The indicator light will illuminate Blue when in Bluetooth mode and Green when in AUX mode. OPERATION FOLLOW THESE STEPS TO UTILIZE THE BLUETOOTH FUNCTIONALITY USING A BLUETOOTH ENABLED DEVICE:

Power the unit On by tapping the Power button once. Select Bluetooth by tapping the Power button until it blinks Blue. Select MTX Sound Bar from the menu on your Bluetooth enabled device. The unit will power on in Bluetooth mode first when it is turned on by tapping. If the Ignition wire is disconnected, (vehicle is turned off and then turned on) the unit will revert back to the previous Bluetooth or AUX setting. Choose Pair when prompted. Once Paired the unit will be able to play audio from your Bluetooth device. The front panel control buttons will control track forward/back and volume up/down in this mode. The Play/Pause button will mute the output and the LED indicator will blink Blue when in Mute mode. FOLLOW THESE STEPS TO UTILIZE BLUETOOTH IN A NFC (NEAR FIELD COMMUNICATION) ENABLED DEVICE:

Power the unit On by tapping the Power button once. Select Bluetooth by tapping the Power button until it blinks Blue. Tap the NFC enabled device on the (left) side of the enclosure (marked by NFC label). Choose Pair when prompted. Once Paired the unit will be able to play audio from your NFC device. FOLLOW THESE STEPS TO UTILIZE AN AUXILIARY INPUT DEVICE:

Power the unit On by tapping the Power button once. Select Auxiliary by tapping the Power button until it blinks Green. Connect an audio device to the AUX input using the Green 3.5mm input on the side of the unit. The LED will illuminate Green, and will blink Green when in mute mode. The front panel control buttons will adjust the Volume up/down in this mode. The Play/Pause button will mute the audio output and the LED indicator will blink Green when in Mute mode. PPAGE 4 302720 DPF-MRK-003 REV D 03/12/20 INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D BA R P LU S B Y M T X, SAT I N B L A C K 2720 KURYAKYN.COM 866 277 9598 | INFO@KURYAKYN.COM 454 COUNTY ROAD VV SOMERSET, WI 54025 USING THE AUXILIARY OUTPUT. OUTPUT MARKED ON (LEFT) SIDE OF ENCLOSURE.

-CONTINUED-

STEP 1 STEP 2 Auxiliary out is a variable output that allows connection to a secondary audio device, whether it is an external amplifier connected to speakers or subwoofer. The Road Thunder Sound Bar Plus can be used with a second Road Thunder Sound Bar Plus unit. For the best audio performance, the second unit connected via Auxiliary should have the volume set to the max. STEP 3 The blue wire on the wire harness can be used as a remote turn on for the second audio device. CONTROLLING THE VOLUME The LED indicator light will blink in both Bluetooth and AUX modes at max volume. STEP 1 STEP 2 USB CHARGING PORT Place USB rubber plug seal onto desired USB cord. Plug USB cord into USB port located on the side of the Road Thunder Sound Bar Plus. This is a charging port only, it is NOT an audio input. PAGE 5 302720 DPF-MRK-003 REV D 03/12/20 INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D BA R P LU S B Y M T X, SAT I N B L A C K 2720 KURYAKYN.COM 866 277 9598 | INFO@KURYAKYN.COM 454 COUNTY ROAD VV SOMERSET, WI 54025

-CONTINUED-

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. LIMITED WARRANTY Kuryakyn warrants that any Kuryakyn products sold hereunder, shall be free of defects in materials & workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions:

1. Kuryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s). 2. The product must be properly installed, maintained & operated under normal conditions. 3. Kuryakyn shall not be liable for any consequential & incidental damages, including labor & paint, resulting from failure of a Kuryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breach of contract or duty between Kuryakyn & a customer. 4. Kuryakyn products are often intended for use in specific applications. Kuryakyn makes no warranty if a Kuryakyn product is used in applications other than intended. 5. Kuryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.s contained in components of Kuryakyn products will be warranted for defects in materials & workmanship for 3 years from the date of purchase whereas all other components shall be warranted for one (1) year. 6. All warranty claims must be directed to the place of purchase. Merchandise sold through internet auction sites or any other unauthorized reseller shall not carry a Kuryakyn warranty. If unsure, please contact the place of purchase to verify they are an authorized Kuryakyn reseller. RETURN POLICY Merchandise determined to be defective may be returned up to one year from the date of purchase. Returns must be processed through original seller. Returned merchandise for any other reason other than warranty claims must be in like new condition & subject to a 20% restocking fee. All returns are subject to inspection for determination of full or partial credit. Any returned part that shows evidence of being used or installed contrary to manufacturers instructions, &/or subjected to improper handling, packaging or return shipping by the customer, will not be eligible for exchange, refund or warranty consideration. All returned electrical items will be inspected & tested. If electrical item is deemed functional, no credit will be issued & item will be returned. All sales are final on discontinued or closeout merchandise. 2015 KURYAKYN HOLDINGS, LLC ALL RIGHTS RESERVED KURYAKYN, KURYAKYN K logo and the marks appearing on this instruction sheet are registered and common law trademarks of Kuryakyn Holdings except noted third-party trademarks. A full listing of trademarks and trademark registrations owned by Kuryakyn Holdings can be found at www.kuryakyn.com/legal-notice. Emissions Notice: The California Air Resources Board (CARB) does not permit the use of aftermarket emission-related parts(s) that alter the performance of OEM emission-related devices unless CARB has issued an Executive Order, other than on racing vehicles on closed courses. Check your local laws and manufacturers information. Listed Manufacturers and product model names are for reference only. All product and company names are trademarks or registered trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them. All specifications are subject to change without notice. For additional information on third-party product and company names, please consult our Web page at www.kuryakyn.com/legal-notice PAGE 6 302720 DPF-MRK-003 REV D 03/12/20 INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D BA R P LU S B Y M T X, SAT I N B L A C K 2720 KURYAKYN.COM 866 277 9598 | INFO@KURYAKYN.COM 454 COUNTY ROAD VV SOMERSET, WI 54025

Mitek Corp Agent Authorization Company: Mitek Corp Address: 1 Mitek Plaza, Winslow, IL. 61089 Product Name: Bluetooth Speaker Model Number(s): K-HSB-SG2, K-HSB-BG2, K-HSB-CG2, Y-HSB-X (Y means customer, X means color or finish) Product Description: Bluetooth Speaker We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: 2019/11/21 Company: Mitek Co

Mitek Corp Daciaration oat aqitrereanca ee OE ee Nata: 9N410_141.94 _ wes wee SS a T tan... tenn... Mm... 2.2. 1O VVNOM H May UONCeI. i atol viwuen v sy cieatianteweninx ma a W atin mma me Biniah\ all aca ace ca bie: hava tha NAP ANS END TIGA Ne EEN were A o flier = NEUTER FN TE IRCAL ID WIE ME OTE Te pengs an same Antenna snape, circuit diagram and RF module, Dut only aimerence on NT Wastin mintwiaenhis SO SISAE OD NEE ENON E NEY 0}

oignatlory

| Name | 1} Simon Broadley LVOonipany Name | MIMeK VOID eee |

| Address | 4 Mitek Plaza Winslow IL 61089 fQOal\ 227 SNnAKN | CAO po Aceany SEG IEP FIV VEO EVE

| &-Mall | simon.broadiey@mitekusa.com

Mitek Corp March 23, 2020 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: 2AAOY-Y-HSB-X Applicant: Mitek Corp Dear Examiner, This is to request a Class II Permissive change for FCC ID: 2AAOY-Y-HSB-X originally granted on 2018/08/15 (date). The change under this application is to Power Amplifier IC of speaker. I attest that the certified device will not be capable of ad-hoc mode operation outside of the grant conditions. Sincerely, Name: Simon Broadley Date: 2020.03.20 Title: Director of Engineering Signature of applicant FCC Class II PC request letter Rev1.1.docx

a cae I cc a tes a el i NTN WE Ey Pe Ivyy redaerai Lommunications Commission 7435 Oakland Mills Road Cahimhia MM 910448 ~

or MEOEN Date: 2019-11-21 Subiect' Request for Confidentiality Se MMC ey MS ENTS MEE OMe mae Tet Se eT aTe ME A TEngR SRNODE TUT AeSIENE = Wot Rew aa Lon SDN ece wm. DAANY yY wep v ee eae ae ee es eee to Whom It May Concer. Pursuant to the nrovicinne nf thea Cammiecinnc nilac Title AT Carctinne 9 ALEZ anA ff ALO we ea fama nR niiw 174: ar SlIANAAA 16 4ANnII eam cilrine Otek: SEE EE we eee Gas MS eee EAMES ORIN SUIS MENTS SITE WO WHTTIOIG Te TOUOWING adacCnment(s) as Connacntal eases eocuMents rom pubic aisciosure indefinitely. Theen Ansrimante ARRO im FAER EEA Ric @ee crewed cence amd leeches conten: ewes enone oxen ee ee ae ee ae a ee, Se SEES a amet: NENT: ene fo aint SERZEENT IIA ao gue cieeon: ps eae each a 7 Tia:

PRES GLTY PUNT auOr itl OPeravon OF Ne EQuIDMeNL | he pubic aisciosure oF nese cocumenis mignt be narmful to our company and would give competitors an unfair advantaae in the market. I-71) @ckiiwesersk Pinnenon NE ESE EGR RENS RAGO gE Caste ee ck:

sa RE tie tm oe Ib DIOCcK Viagram L_| Parts List WS Onerational Deecrintion en ee a ee ae c+. a a an Ly MS MY PE In additional to above mentioned documents. in order to comply with the marketing requlations in Title: 47 CER 29 RNS and tha innnatiAn Wilke feo THe AT OOCD A DAONA ScHIK RRR Bc ee ree See:

Dike pace wAcaicek: watcecen teen: Bie Wrcceniite Re eek nik een gta ee ED Rh ne ee eee es ee ee es NE IS SOONG BNET ESTING GMTIME eal GNU Ue a@CiUal Mlarkedng OF Newly eee ae auuronzed Gevices, we request onort !erm Confidentiality of the following attachment(s);

NS Evteamal Dranine a |

TT s+rAnt nk Mens. aN fae well PS C a aaa WwW intemal Fnotos User Manual ee a a ae a a ee ee es Lu) Mt SY Mayo, PUPOUGII WY PUM INUULS UA US lio.

(<1 For 180 davs pursuant to KDB 726920 D001. BN al ce cn a ter aE erence: Beicall, wee Helo UU GMS Olay Glial aul Hea oUreinlenit loot PeVOrts, FUL IL label formal and correspondence auring the certification review process cannot be granted as confidential]

documents and this information will be available for nublic review ance the arant af aniinmart ab Sea aaicea is a le ieeriasl NS ee ee a a ee ee Nee ee eee Oe ees Sincerely, Name: Simon Broadley if oO eS NG BF (CMVea (MoE INY