Telephone service is available Telephone service is available Installation Guide Modem Fiber Optic Content Modem Fiber Optic Adaptor Cable Installation Guide Set up telephone Attention the fiber optic cable that connects your device is very delicate. to pull it hard to avoid broken. We advise you not This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This product has been tested and complies with the If this device does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
i. Reorient or relocate the receiving antenna ii. Increase the separation between the equipment or devices iii. Connect the equipment to an outlet other than the receiver's iiii. Consult a dealer or an experienced radio/TV technician for assistance Installation explantion Connect the Fiber Optic cable to the Fiber Optic port of the device (1) and then the other end to the Optical fiber socket of your home. Use a telephone cable to connect the device's Telf port (2) with a telephone socket in your home (if you only use a landline, you can plug it directly into the device's Telf port instead of using the jack). Plug the power adapter into the mains and the connector of the DC port equipment while the update is taking place, as it could damage the system:12V-2A (3). Power on Optical Fiber Optic To turn on the Modem you must press the ON OFF switch located on the back of the device. status blue blue blue Telephone service is available Wi-Fi interface function correctly Connect with internet Movistar modem provides optimize internet configuration Movistar can automatically perform at some time, especially at the first installation, a remote update of the software of your device to offer you a better service and operation. During this process the LEDs will flash and after a few minutes the Installation and connection of the indicator lights will remain as in the previous table if everything worked correctly. If a red light comes on, it means that there is abnormal operation of the equipment. If so, we recommend that you turn off and on the device
(quiet because you will not lose your network configuration). If the problem persists you can perform a factory reset or contact the Movistar service lines. Attention: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must be at least 20 cm from the user and must not be co-located or operating in conjunction with any other antenna or transmitter. Connect your devices You can connect your devices via Data Cable (Ethernet) and also through wireless network (WiFi). At times when you require a higher connection speed, we recommend connecting through the data cable. Remember that this must be Category 5e or higher. Connection via wireless network (WiFi) To be able to use the wireless connection, activate the WiFi of your device. Then it searches the available WiFi networks. Select the one whose Name is on the label below your modem and carefully enter the WiFi Key (composed of numbers and letters). Connection via cable Ethernet Connect an Ethernet cable and turn on your device or computer. The Ethernet port light will light green indicating that the connection is correct and will flash if there is activity. Congratulations, you can now navigate with your Movistar Optical Fiber!
Advanced configuration options 1 - Enter the router's Web portal, accessing with the browser the address associated to the equipment http://192.168.1.1:8000. To access this website you must enter the password that you will find in the label below your modem called "Modem access data"
Connection by scanning the QR tag:
If your Smartphone or Tablet has a QR code reader, you can scan the code labeled "WiFi". In this way you can quickly obtain the information of your wireless WiFi network, and if your device allows it, it will automatically connect you. Note: This code is only valid to synchronize the parameters of the network with the factory configuration of your Movistar Modem. Quick connection via WPS Restore to factory values If your device supports WPS you can establish the WiFi connection using this method. Make a short press (1 second is enough) of the WiFi / WPS button on the back of the Medem. Then activate the WPS on your device within the next 2 minutes. 1. With the modem on, press the reset button on the modem with a pen tip for at least 10 seconds, and then release it. 2. After approximately 90 seconds, your modem will have factory values again
(the Wifi and Password data will be the ones that appear on the labels)