TM APRUS II Operation Manual Mixlinker Networks (Shenzhen) Inc. Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1)Reorient or relocate the receiving antenna. 2)Increase the separation between the equipment and receiver. 3)Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4)Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To comply with FCC RF exposure compliance requirements,this grant isapplicable to only mobile configurations. The antennas used for this transmittermust be installed to provide a separation distance of at least 20 cm from allpersons and must not be co-located or operating in conjunction with any otherantenna or transmitter. Contents I. Introduction ------------------------------------------------------------- 01 II. Nomenclature --------------------------------------------------------- 02 III. Packing List ------------------------------------------------------------ 03 IV. Specification ---------------------------------------------------------- 03 V. Interfaces ---------------------------------------------------------------- 04 VI. Indicators -------------------------------------------------------------- 08 VII. Connections ---------------------------------------------------------- 09 VIII. Installation ----------------------------------------------------------- 10 IX. FCC Warnning --------------------------------------------------------- 12 I. Introduction Welcome to use the Advanced Programmable Remote Utility Server (APRUS II) of Mixlinker Network (Shenzhen) Inc. (herafter referred to as Mixlinker). APRUS is an advanced programmable Internet of Things adaptor for industrial equipment developed by Mixlinker. APRUS II is the second generation product of Mixlinker, and will be referred to as APRUS II. APRUS II is an intermediate adapter developed to address theneeds of traditional equipment for IoT. Adaptors are used to establish data communication with equipment (controller) without making changes to equipment, by way of adapting, to send the operation status and data to IoT platform, so as to make the right judgement and take right action to reduce the malfunction of equipment, lowing operation cost. This manual briefly introduces APRUS II to customers, and provide help to customers for using the product. 01 II. Nomenclature A2 - 4207 - B Product Info Mixlinker Advanced Programmable Remote Utility Server (APRUS II) Power Input AC/DC 24V Input Communication Modules 4 2G Communication Module Interfaces 0 CAN,RS485-1,RS485-2 GPS Modules 2 Module with GPS 02 III. Packaging List APRUS II (1) GSM Antenna (1) Micro SIM Card (1) IV. Specification GPS Antenna (1) - optional Item Settings/Configurations GPRS Antenna Interface Wireless Network Standard SMA Interface
(Female Connector) GPRS 2G Network
(Not Supporting CDMA) Input Voltage AC/DC9~24V Maximum Power Dissipation Average Power Dissipation 3W 1W Operating Temperature
-20 C to +45C Storage Temperature
-40 C to +100C Operating Humidity Storage Humidity Weight Dimension 45%-80%
30%-90%
210g 146*97*49mm RS485 Interface Isolated USB Interface Mini USB Female Connector 03 V. Interfaces APRUS II (Interfaces on Top) GPS GSM ETH 1 2 3 No. Symbol Definition 1 2 3 GPS GSM ETH GPS Antenna Interface GSM Antenna Interface Ethernet Interface (Optional) APRUS II (Interface on Left Side) No. 1 Symbol EXT 1 Definition Extended Interface 04 V. Interfaces APRUS II (Interfaces on Right Side I S M 1 2 Symbol Definition I S M Micro SIM Card Slot USB Interface No. 1 2 APRUS II, when using Micro SIM card, please insert the cardchip down and notched edge facing outward 05 V. Interfaces APRUS II (Interfaces on the Bottom) Note When choosing adapters of one RS485 and one RS232, the default for 3 and 4 is RS232, and 6 and 7 is RS485 No. 1 2 3 4 5 6 7 8 9 10 11 Item CAN-L CAN-H TX/A-1 RX/B-1 GND TX/A-2 RX/B-2 GND SGND POW +
POW -
L
-
N A C H
-
N A C 1
-
A
/
X T 1
-
/
B X R D N G 2
-
A
/
X T 2
-
/
B X R D N G D N G S
+
W O P
-
W O P 1 3 5 7 9 11 2 4 6 8 10 Indicator CAN-L CAN-H RS232_TX1/RS485_A1 RS232_RX1/RS485_B1 Shared Ground RS485_A2 RS485_B2 Shared Ground Shell Ground Polarity - Positive Polarity - Negative 06 V. Interfaces APRUS II (Front) 5 6 RST SOS 4 3 GSM SVR GPS PWR 1 2 No. 1 2 3 4 5 6 Item GSM SVR GPS PWR RST SOS Indicator GSM Indicator Light SVR Indicator Light GPS Indicator Light Power Indicator Light Reset Button SOS Button Note:
Press SOS to trigger a short press event. Press and hold for 3 seconds to trigger a long press event. Event will be handled by FIDIS, and may be customized according to customers'needs. 07 VI. Indicators Note: During electrical initialization and self-testing on adaptors, the SVR, GPS and PWR indicators will simultaneously be on for 500ms and off for 500ms. Normal Abnormal 1. Upon successful logon of SIM card, indicator shall be on at the interval of 3000ms, for 64ms each time. 2. Upon the connection of GPRS and module is working normally, indicator will be on at the interval of 300ms, for 64ms each time. 1. When SIM card is not registered online, indicator shall be on at the interval of 800ms, for 64ms each time. 2. When module is not powered on, indicator shall be off. Status Indicator 1 GSM Status Indicator 2 SVR Status Indicator 1. When GARDS is correctly connected, indicator shall be on at the interval of 2s, for 60ms each time. 1. When there is no signal for SIM card, or not connected to antenna, indicator shall flash three times every 2s, for 60ms each flashing. 2. Failure of SIM card registration with vendor, indicator shall flash three times every 2s, for 60ms each flashing. 3. When SIM card is not activated, indicator shall flash three times every 2s, for 60ms each flashing. 4. When SIM card is not inserted securely, or the slot on adaptor becomes loose, or slot power source is not compatible with SIM card, indicator shall flash two times every 2s, for 60ms each flashing. 5. When adaptor is not connected to server, indicator shall flash four times every 2s, for 60ms each flashing. 3 GPS Status Indicator 1. When GPS signal is normal, indicator shall be on two times every 2s, for 60ms each time. 1. When GPS signal is not normal, indicator shall be off. 4 Power Status Indicator 1. When power is connected normally, indicator will be on constantly. 2. When MCU is being upgraded, indicator shall flash quickly at the interval of 2s. 1. When power is not connected normally, indicator will be off. 08 VII. Connections CAN Interfac CAN Interfac CAN-L CAN-H RS232 Interfac Rs232 Interfac RX/B-1 TX/A-1 GND PLC RS485 Interfac TX/A-2 RX/B-2 GND RS485 Interfac Power Interface Power Interface SGND POW +
POW -
CAN-L CAN-H TX/A-1 RX/B-1 GND TX/A-2 RX/B-2 GND SGND POW +
POW -
Note:
1.This wiring diagram demonstrates an adaptor with a grouping of RS485 and RS232. For adaptors with two groups of RS485, please refer to the above diagram for the wiring of RS485. Please follow the correct wiring. Otherwise data will not be collected from equipment. 2.Please connect the antennas of GPS and GSM correctly. Otherwise equipment shall not pick up signal and GPS will not locate the position. GPS Antenna Interface GSM Antenna Interface Ethernet Interface (Optional) CAN-L CAN-H TX/A-1 RX/B-1 GND TX/A-2 RX/B-2 GND SGND POW +
POW -
APRUS II G P S G S M E T H 09 VIII. Installation There are two methods for APRUS II installation: 1. With screws, screw size: M4.5, as shown below:
10 VIII. Installation 2. Installation with rails, the size of rail: 35mm, as shown below:
Install stopper 3 5 m m Rail Step 1 Raise the stopper on the adaptor. Step 2 Install the adaptor onto the rail. (Please secure the bottom rail groove onto the rail bottom first.) Note:
1. For the safety of you and the equipment and adaptor, please power off the equipment prior to performing the installation. 2. Prior to installation, please insert SIM card into slot and complete all the wiring correctly on adaptor. 11 Step 3 Push down the stopper. Mixlinker Networks (Shenzhen) Inc. 3/F Spring Tower, Meisheng Creative Valley, 10 Longchang Rd. Shenzhen 0755-23740592 www.mixlinker.com V1.0