Document Rev 0.2 DRAFT
<MODULE PHOTO GOES HERE>
MMB Networks LKT00 ZigBee Module based on the NCS36510 LKT00 The MMB Networks LKT00 ZigBee module is a drop-in ZigBee/802.15.4 module for use in wireless mesh networking applications. The module is based on ON Semiconductors NCS36510 SoC. The NCS36510 is a low power, fully integrated, System on Chip that integrates a 2.4 GHz IEEE 802.15.42006 compliant transceiver, ARM CortexM3 microprocessor, RAM and FLASH memory, a true random number generator, and multiple peripherals to support design of a complete and secure wireless network with minimal external components. The NCS36510 incorporates an industry leading 32 bit ARM CortexM3 for high performance, low power and low cost processing. The NCS36510 includes 640 kB of embedded FLASH memory for program storage along with 48 kB of RAM for data storage. NCS36510 uses a hardware accelerated MAC to minimize processor overhead while maximizing available processor power for running application software. Peripherals include DMA, UART(2), SPI(2), I2C(2), PWM, RTC, three programmable timers, WDT, 18 GPIO, 10 bit ADC with four external inputs and integrated temperature and voltage sensors. Table of Contents 1 General Information ................................................................................................................. 1 2 Memory .................................................................................................................................... 1 3 Module Pinout .......................................................................................................................... 1 3.1 Debug and Programming Interface ................................................................................................ 1 4 Electrical Specifications ............................................................................................................ 2 4.1 Absolute Maximum Ratings ........................................................................................................... 2 4.2 Recommended Operating Conditions ............................................................................................ 2 4.3 DC Electrical Characteristics ........................................................................................................... 2 4.3.1 Core Power Consumption ....................................................................................................... 2 4.4 TX Power Setting ............................................................................................................................ 3 5 RF Specifications ....................................................................................................................... 3 5.1 Receive Specifications .................................................................................................................... 3 5.2 Transmit Specifications .................................................................................................................. 3 6 Mechanical Specifications ........................................................................................................ 3 6.1 Physical Dimensions ....................................................................................................................... 3 6.2 Recommended Land Pattern (Surface Mount) .............................................................................. 4 Labeling .......................................................................................................................................... 4 6.3 7 Soldering Temperature Time Profile for Reflow Soldering (Lead-Free Solder) ........................ 4 8 Regulatory Approvals ............................................................................................................... 5 8.1 Approved Antennae ....................................................................................................................... 5 8.2 Federal Communications Commission (FCC - US) .......................................................................... 5 8.2.1 RF Output Power Settings ....................................................................................................... 5 8.2.2 FCC Notice ............................................................................................................................... 5 8.2.3 Modular Approval ................................................................................................................... 5 Labeling Requirements ............................................................................................................ 5 8.2.4 Industry Canada (IC) ....................................................................................................................... 6 8.3.1 RF Output Power Settings ....................................................................................................... 6 IC Notice .................................................................................................................................. 6 8.3.2 8.3.3 Labeling Requirements ............................................................................................................ 6 8.4 ETSI (EU) ......................................................................................................................................... 6 8.4.1 RF Output Power Settings ....................................................................................................... 6 8.4.2 ETSI Approval .......................................................................................................................... 6 9 Ordering Information ............................................................................................................... 7 8.3 1 General Information Note that some of the specifications refer to either NCS36510 or Module. Please note specifications cited as NCS36510 are taken from the NCS36510 datasheet (this should also be noted where referred to). Module means measurements taken with the MMB Networks production module. 2 Memory RAM (kB) 48 On-Chip Flash (kB) 640 3 Module Pinout Module Pad NCS36510 GPIO (NCS36510 Pin Number) Test (35) DIO17 (40) DIO10 (1) DIO16 (4) VDDIO (5) GND DIO8 (3) DIO7 (7) DIO6 (8) DIO5 (9) DIO4 (10) DIO3 (11) DIO2 (12) DIO1 (13) DIO0 (14) nReset (36) DIO9 (2) VDD (22, 34) GND A0 (23) DIO13 (37) DIO12 (38) DIO11 (39) GND A1 (24) DIO15 (6) DIO14 (15) A2 (29) A3 (30) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 3.1 Debug and Programming Interface DRAFT TBD Rev 0.2 DRAFT Page 1 of 7 LKT00 Module Datasheet DRAFT 3.9 Units Minimum Maximum
-0.3
-0.3
-0.3
-40 VDDIO+0.3, <=3.9 VDD+0.3, <=3.9 4 Electrical Specifications 4.1 Absolute Maximum Ratings Parameter Supply Voltage (VDD, VDDIO) Voltage on any GPIO (DIO0:DIO17, nReset, Test) Analog pin voltage (A0:A3) Storage Temperature Range 4.2 Recommended Operating Conditions Parameter Supply Voltage (VDD) 3V Mode Supply Voltage (VDDIO) Ambient Temperature Range 4.3 DC Electrical Characteristics For typical values TA = 27C, for min/max values TA = 40C to 85C; unless otherwise noted. Power supplies VDD = 3.3 V, VDDIO = 3.3 V, unless otherwise noted. Parameter Coma Mode Sleep Current1 Test Condition 3.3 3.3 27 3.6 3.6 85 TBD TBD
-40 V V C Maximum Maximum Minimum Minimum V V V C Typical Units
+125 Typical 0.65 4.96 Units A A 3 V Mode, Switching Regulator 3 V Mode, Linear Regulator2 10k 10 2.3 5 3 cycles mA mA mA years Test Condition Minimum
+7.6 dBm (Max. Power Setting) 0 dBm 16 dBm (Min. Power Setting)
+7.6 dBm (Max. Power Setting) 0 dBm 16 dBm (Min. Power Setting) Typical TBD TBD TBD TBD TBD TBD TBD Maximum Units mA mA mA mA mA mA mA 3V Mode Receive Current Switching Regulator4 3V Mode Receive Current Linear Regulator4 Notes:
1. Coma mode = CPU running on internal 32 kHz osc and waiting for interrupt, both retention RAMS disabled, all other functions powered down TBD mA Rev 0.2 DRAFT Page 2 of 7 LKT00 Module Datasheet DRAFT FLASH Erase Cycles Before Failure3 FLASH Read Current3 FLASH Erase Current3 FLASH Write Current3 Data Retention at 85C 4.3.1 Core Power Consumption Parameter 3V Mode Transmit Current Switching Regulator4 3V Mode Transmit Current Linear Regulator4 2. VDD = 2.0V 3. Guaranteed by design 4. Peripherals disabled, CPU halted, 32 MHz crystal oscillator, CW Mode, 2.44GHz, ON Semiconductor evaluation board, conducted measurement, 50 ohm system Please refer to the NCS36510 data sheet for DIO specifications including internal resistor values, switching voltages, thresholds, etc. 4.4 TX Power Setting The RF Output power of the Module can be adjusted via the SoCs TX Power settings. The Transmit Current will also vary according to the TX Power setting. The charts below show the relationship between the Transmit Current or Output Power vs the TX Power setting. CHART TBD 5 RF Specifications 5.1 Receive Specifications Parameter Frequency range Sensitivity RSSI range 5.2 Transmit Specifications Parameter Output Power Test Condition Minimum Typical Maximum 2400
-97 40 2485
-92 60 Units MHz dBm dB Maximum 10 35
-20
-30 Units dBm
%
dBc dBm Test Condition Minimum Max Power Setting 2 Typical 7.6 Error Vector Magnitude (EVM) Max Power Max power Spurious emissions, relative Spurious emissions, absolute Max power 6 Mechanical Specifications 6.1 Physical Dimensions Dimension Drawing TBD Symbol L W H A1 A2 Rev 0.2 DRAFT Length of the module Width of the module Height of the module Pitch Distance center of pad to PCB edge Description 10 Distance Page 3 of 7 LKT00 Module Datasheet DRAFT Description Distance center of pad to PCB edge Length of keep-out zone Width of keep-out zone Keep-out zone from corner of PCB Keep-out zone from corner of PCB Symbol A3 A B C D 6.2 Recommended Land Pattern (Surface Mount) Land Pattern TBD Symbol F1 F2 F3 F4 F5 F6 6.3 Labeling Description Distance pad edge to pad edge Distance pad edge to pad edge Distance pad edge to pad center Pitch Module silkscreen outline Module silkscreen outline Distance Distance 7 Soldering Temperature Time Profile for Reflow Soldering (Lead-Free Solder) Rev 0.2 DRAFT Page 4 of 7 LKT00 Module Datasheet DRAFT 8 Regulatory Approvals 8.1 Approved Antennae The LKT00 module has been certified with one onboard chip antenna. See the individual jurisdictions below for the detailed output power settings. 8.2 Federal Communications Commission (FCC - US) 8.2.1 RF Output Power Settings For the LKT00 module using the onboard chip antenna, the approved power level settings are 10 (max power) for channels 11- 25 and X for channel 26. 8.2.2 FCC Notice The LKT00 device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. To comply with FCC RF Exposure requirements, users of this device must ensure that the module be installed and/or configured to operate with a separation distance of 20cm or more from all persons. Usage of Channel 26 at full power will result in non-compliance to FCC standards. MMB recommends avoiding use of channel 26 and if necessary only use with a reduced power setting. For further details please contact MMB. 8.2.3 Modular Approval The LKT00LKT00 device meets the requirements for modular transmitter approval as detailed in the FCC public notice DA 00-1407. It should be noted that:
While the applicant for a device into which an authorized module is installed is not required to obtain a new authorization for the module, this does not preclude the possibility that some other form of authorization or testing may be required for the device (e.g., a WLAN into which an authorized module is installed must still be authorized as a PC peripheral, subject to the appropriate equipment authorization).
-- FCC Public Notice DA 00-1407 Caution:
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 8.2.4 Labeling Requirements The user of this device is responsible for meeting the FCC labeling requirements. A clearly visible label on the exterior enclosure of an incorporating device must list the MMB Research Inc. FCC ID XFF-LKT00 and the FCC Notice above
. The exterior label should use the wording Contains or Contains Transmitter Module. For example:
Contains FCC ID: XFF-LKT00 Rev 0.2 DRAFT Page 5 of 7 LKT00 Module Datasheet DRAFT or Contains Transmitter Module FCC ID: XFF-LKT00 Any similar wording that expresses the same meaning may be used. 8.3 Industry Canada (IC) IC Notice 8.3.1 RF Output Power Settings For the LKT00 module using the onboard chip antenna, the approved power level settings are 10 (max power) for channels 11- 25 and X for channel 26. 8.3.2 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 8.3.3 Labeling Requirements The host device shall be properly labeled to identify the modules within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words Contains transmitter module, or the word Contains, or similar wording expressing the same meaning, as follows:
Contains transmitter module IC: 8365A-LKT00 8.4 ETSI (EU) 8.4.1 RF Output Power Settings For the LKT00 module using the onboard chip antenna, the approved power level settings are 10 (max power for all channels). 8.4.2 ETSI Approval Provided that the above TX Power settings are used, the LKT00 module is compliant with the following EU standards:
ETSI EN 300 328 (v1.9.1), ETSI EN 301 489 1 (v1.9.2) and ETSI EN 301 489 17 (v2.2.1) Rev 0.2 DRAFT Page 6 of 7 LKT00 Module Datasheet DRAFT 9 Ordering Information SKU NCAT00LKT00082G4MNG Description Rev 0.2 DRAFT Page 7 of 7 LKT00 Module Datasheet DRAFT