Sports 7000 Series ST702 User manual Register your product and get support at www.philips.com/support Contents 1 Important safety instructions 2 2 Hearing Safety General information 2 2 Your Bluetooth wireless earpieces What's in the box Other devices Overview of your Bluetooth wireless earpieces 3 3 3 4 3 Get started 5 5 Charge the battery Pair the earpieces with your Bluetooth device at the rst time Pair the earpieces with another Bluetooth device 6 6 4 Use your headphones Reconnect the earpieces to your Bluetooth device Power on/o Manage your calls and music LED indicator status How to wear 5 Factory reset the earpieces 6 Technical data 7 Notice Declaration of conformity Disposal of your old product and battery Compliance with EMF Environmental information Notice of compliance 7 7 7 7 8 8 9 10 11 11 11 12 12 12 7 Frequently asked questions 13 General information To avoid damage or malfunction:
Caution Do not expose headphones to excessive heat Do not drop your headphones. Headphones shall not be exposed to dripping or splashing. Do not allow your headphones to be submerged in water. Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. About operating and storage temperatures and humidity Operate or store in a place where temperature is between -10C
(14F) and 50C (122 F) (up to 90%
relative humidity. Battery life may be shorter in high or low temperature conditions. 1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guide-
lines when using your earpieces. Listen at reasonable volumes for reasonable periods of time. Be careful not to adjust the volume continuously upwards as your hearing adapts. Do not turn up the volume so high that you can't hear what's around you. You should use caution or tempo-
rarily discontinue use in potentially hazardous situations. Excessive sound pressure from earphones and headphones can cause hearing loss. Using headphones with both ears covered while driving is not recom-
mended and may be illegal in some areas while driving. For your safety, avoid distractions from music or phone calls while in trac or other potentially dangerous environments. USB charging cable (for charging only) Quick start guide Other devices A mobile phone or device (e.g. note-
book, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the earpieces
(see 'Technical data' on page 10). 2 Your Bluetooth wireless earpieces Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/welcome. With this Philips wireless earpieces, you can:
enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music. What's in the box Philips True Wireless earpiec-
es Philips ST702 Replaceable rubber ear caps x 2 pairs Charging case Overview of your Bluetooth wireless earpieces Ear Cap Microphone Multi-function Button LED indicator (charging case) Micro USB charging slot 3 Get started Charging process is veried by white LED light on the earpiecess. When the earpieces is fully charged, the white light goes o. Charge the battery Note Before you use your earpieces for the rst time, place the earpiecess in the charging case and charge the battery for 3 hours for optimum battery capacity and lifetime. Use only the original USB charging cable to avoid any damage. Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces o. Charging case Connect one end of the USB cable into the charging case, and another end into the power source. The charging case starts charging. Charging process is veried by the blue LED light next to the USB socket on the case. When the charging case is fully charged, the blue light goes on. Tip The charging case serves as a portable backup battery for charging the earpieces. When the charging case is fully charged, it supports 3 full recharge cycle for the earpieces. Earpieces Place the earpieces in the charging case. The earpieces start charging. Tip Normally, a full charge takes 2 hours (for the earpieces or charging case). Pair the earpieces with your Bluetooth device at the st time Auto Power on: Open the charging capsule, the earpiecess discharged and the blue LED indicator ash with power on voice prompt. Manual Power on: On both earpiecess press and hold the multi-function buttons for approxinmately 2 seconds. 1 second 02 The LED on both earpiecess ashes in blue for 3 times, and then it
ashes in white. Both earpiecess are now power on and are paired with each other. The earpiecess are now in pairing mode and is ready to pair with a Bluetooth device
(e.g. a mobile phone) Turn on the Bluetooth function of your Bluetooth device. Pair the earpiecess with your Bluetooth device. Refer to the user manual of your Bluetooth device. Note After powering on, if the earpieces cannot nd any previously connected Bluetooth device, it will automatically switch to pairing mode. The following example shows you how to pair the earpieces with your Bluetooth device. Turn on the Bluetooth function of your Bluetooth device, select Philips ST702. Enter the earpieces password 0000 (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password. Philips ST702 UV sterilization function Put the earpieces into the charging case and close the charging case, the white LED on 20 seconds for earpieces UV sterilization function. UV sterilization 20 Pair the earpieces with another Bluetooth device If you have another Bluetooth device that you want to pair with the earpieces, make sure the Bluetooth function in any other previously paired or coonected devices are turned o. Then follow the steps in Pair the earpieces with your Bluetooth device at the rst time. Note The earpieces stores 1 device in the memory. If you try to pair more than 2 devices, the earliest paired device is replaced by the new one. 4 Use your earpieces Connect the earpieces to your Bluetooth device Turn on the Bluetooth function of your Bluetooth device. Take both earpiecess from the charging case, the earpieces will power on and reconnect automati-
cally. If no device is connected, the earpieces will automatically turn o after 3 mins. Both earpiecess are now powered on and are paired with each other automatically. The earpieces will search the last connected Bluetooth device and reconnect to it automatical-
ly. If the last connected one is not available, the earpieces will search and reconnect to the second last connected device. Tip The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect. If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manully. Note If the earpieces fails to connect to any Bluetooth device within 3 minutes, it will turn o automatically to save the battery life. In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually. Power on/o Task Turn the earpieces on. Turn the earpieces o. Multi-
function button Right/Left earpieces Right/Left earpieces Operation Press and hold for 2 seconds. Place both earpiecess in charging case. Press and hold for 4 seconds. The white LED
ashes 3 times. Manage your calls and music Music control Task Multi-
function button Right/Left earpieces Play or pause music Skip forward Right earpieces Skip backward Left earpieces Operation Press twice Press and hold for 2 seconds Press and hold for 2 seconds Call control Task Pick up/hang up call Reject an incomging call Multi-
function button Right/Left earpieces Right/Left earpieces Operation Press twice Press and hold for 2 seconds Voice control Task Siri/Google Multi-
function button Right/Left earpieces Operation Press three times LED indicator status Earpieces status The earpieces is connected to a Bluetooth device. Indicator The blue LED light
ashes for every 5 seconds. The earpieces is powered on. The earpieces is pairing mode. The earpieces is on but not connected to a Bluetooth device. The white LED
ashes 3 times. The blue LED
ashes. The blue LED will
ashes. If no connection can be made, the earpieces will turn itself o within 15 minutes. Low battery level
(earpieces). Low battery level
(charging case). Battery is fully charged (earpiec-
es). Battery is fully charged (charging case). You will hear battery low on the earpieces. The blue LED on the charging case
ashes every 1 second. The white LED light on the earpieces is o. The white LED light on the charging case is o. Battery LED indicator on Bluetooth device It will show a battery indicator on Bluetooth device after connected to earpieces. How to wear 5 Factory reset the earpieces In Power o status, press and hold the multi-function button of the earphone for around 8 seconds until the LED indicator ashing red and blue alternately (or take the earphone out of the charging capsule and wait for the LED indicator ofthe earphone
ashing red and blue alternate-
ly.),doubleclick the touch control button and the LED indicator will
ash red and blue once at the same time,reset the factory setting and the earphone will power o after the operation. Remark: if the Master and Slaver clear the paring list at the same time, you have to pairing as st time use then both earbuds can pairing as TWS. In order to operation easier we recommended clear the earbuds pairing list one by one. 6 Technical data Earpieces Music time: 6 hours (additional 6 hrs with charging case) Talk time: 6 hours (additional 6 hrs with charging case) Standby time: 200 hours Charging time: 2 hours Rechargeable lithium ion battery:
105 mAh on each earpieces Bluetooth version: 5.0 Compatible Bluetooth proles:
HSP (Hands-Free Prole-HFP) A2DP (Advanced Audio Distri-
bution Prole) AVRCP (Audio Video Remote Control Prole) Supported audio codec: SBC Frequency range: 2.402 -2.480GHz Transmitter power: < 4 dBm Operating range: Up to 10 meters (33 feet) Charging case Charging time: 2 hrs Rechargeable Li-ion battery: 450mAh Note Specications are subject to change without notice. 7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compli-
ance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can nd the Declaration of Conformity on www.p4c.philips.com. Disposal of your old product and battery Your product is designed and manufac-
tured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an ocial collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environ-
ment and human health. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones. Make sure the earpieces is discon-
nected from the charging case before removing the battery. Make sure the charging case is disconnected from the USB charging cable before removing the battery. 1 2 3 Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassem-
bled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between equipment and receiver Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Notice of compliance The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Develop-
ment Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage; (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CAN ICES-3(B)/NMB-3(B) IC Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 8 Frequently asked questions My Bluetooth earpieces does not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. Put both earpiecess into charging case. Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices. On your Bluetooth device, delete Philips ST702 from the Bluetooth list. Pair your earpieces (see Pair the earpieces with your Bluetooth device at the rst time on page 6). How to reset pairing. Take both earpiecess out of the charging case. Press twice on both earpiecess Multi-function buttons until the LED indicator turns white, wait for about 10 seconds. You will hear Connected, Left Channel, Right Channel, as pairing successful. The Bluetooth device cannot nd the earpieces. The earpieces may be connected to a previously paired device. Turn o the connected device or move it out of range. Pairing may have been reset or the earpieces has been previously paired with another device. Pair the earpieces with the Bluetoot device again as described in the user manual.
(see Pair the earpieces with your Bluetooth device at the st time on page 6). My Bluetooth earpieces is connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the earpieces. The audio quality is poor and crackling noise can be heard. The Bluetooth device is out of range. Reduce the distance between your earpieces and Bluetooth device, or remove obstacles between them. Charge your earpieces. The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all. Make sure your mobile phone not only supports (mono) HSP/HFP but alos supports A2DP and is BT4.0x (or higher) compatible (see Technical data on page 10). I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward). Make sure the Bluetooth audio source supports AVRCP (see Technical data on page 10). The volume level of the earpieces is toot low. Some Bluetooth devices cannot link the volume level with the earpieces through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level. I cannot connect the earpieces to another device, what do I do?
make sure the Bluetooth function of the previous paired device is turned o. Repeat the pairing procedure on your second device (see Pair the earpieces with your Bluetooth device at the
rst time on page 6). I hear sound from only one earpieces. If you are in a call, it is normal that sound comes from the right and left earpieces. If you are listening to music but sound only comes from one earpieces:
The other earpieces may be out of battery. For optimal performance, charge both earpieces fully. The right and left earpiecess are disconnected from each other, Turn o both earpieces rst. Then put both earpiecess back to charging case for 5 seconds and take them out. This will turn the earpiecess on and connect the two earpiecess. Reconnect the earpieces to your Bluetooth device. The earpieces is connected to more than one Bluetooth device. Switch o the Bluetooth function of all connected devices. Turn o both earpiecess. Put both earpiecess back to charging case for 5 seconds and take them out. Reconnect the earpieces to your Bluetooth device. Note that the earpieces is desighed for connecting to only one Bluetooth device ath a time. When you reconnect the earpieces to your Bluetooth device, make sure the Bluetooth function of any other Previously paired/connected devices are o. If the above solutions do not help, factory reset the earpieces (see Factory reset the earpieces on page 9). For further support, visit www.philips.com/support. Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Este produto est homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resoluo 242/2000, e atende aos requisitos tcnicas aplicados. Para maiores informaes, consulte a site da ANATEL: www.anatel.gov.br Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its aliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAST702_00_EN_v0.1